Cutters and Cutting Machinery

Fairfield, NJ – AZCO Corp. has designed a tubing cutter capable of making highly accurate cuts at a 45-° angle.  The unit has accuracy of +/- 2.5mm [0.1” at 100mm [3.9” lengths.  It can cut heavy and thin plastic or rubber non-wire reinforced tubing up to 25mm [1” in diameter. This system is offered as a stand alone table top unit, or it can be a slave to your process.  The...

Read More »
Droplet Splitting System creates nano and picoliter droplets.
Splitters

Droplet Splitting System creates nano and picoliter droplets.

Designed for generation of miniaturized droplet compartments, Mitos Dropix-® enables rapid production of droplets — typically between 50 nL and 1 µL — of up to 24 different samples, with precise control over droplet content and size, as well as frequency. Integrated Droplet Junction Chip enables subsequent splitting into monodisperse droplets from 500 to 2,000 pL. For maximum flexibility,...

Read More »
Droplet Splitting System creates nano and picoliter droplets.
Splitters

Droplet Splitting System creates nano and picoliter droplets.

Designed for generation of miniaturized droplet compartments, Mitos DropixÂ-® enables rapid production of droplets — typically between 50 nL and 1 µL — of up to 24 different samples, with precise control over droplet content and size, as well as frequency. Integrated Droplet Junction Chip enables subsequent splitting into monodisperse droplets from 500 to 2,000 pL. For maximum...

Read More »
Barcode Scanners / Readers

Modular Systems offer product traceability and code reading.

Designed for automated test lines, SCU-439 JOT Scanner Unit and FMM-440 JOT Fail Separation Unit can be used with process equipment that needs product identification data or to mark/separate faulty products after process. Identification occurs by reading codes such as 2D, 3D, and RFID. SCU-439 sends code data through RS232 or Ethernet to next process unit that needs identification, while FMM-440...

Read More »
Barcode Scanners / Readers

Modular Systems offer product traceability and code reading.

Designed for automated test lines, SCU-439 JOT Scanner Unit and FMM-440 JOT Fail Separation Unit can be used with process equipment that needs product identification data or to mark/separate faulty products after process. Identification occurs by reading codes such as 2D, 3D, and RFID. SCU-439 sends code data through RS232 or Ethernet to next process unit that needs identification, while FMM-440...

Read More »
BGA Socket Adapter accepts 724-pin BGA, 1 mm pitch IC.
Electronic Sockets

BGA Socket Adapter accepts 724-pin BGA, 1 mm pitch IC.

Consisting of female socket module and male adapter module, BGA Socket Adapter accommodates 724-pin, 1 mm pitch, 35 x 35 mm IC size. SF-BGA724A-B-42F female socket module can be soldered to motherboard using standard soldering methods without warping. Similarly, BGA device can be soldered to male adapter module. Both are constructed with high-temperature FR-4 substrate, assuring match with target...

Read More »
BGA Socket Adapter accepts 724-pin BGA, 1 mm pitch IC.
Electronic Sockets

BGA Socket Adapter accepts 724-pin BGA, 1 mm pitch IC.

Consisting of female socket module and male adapter module, BGA Socket Adapter accommodates 724-pin, 1 mm pitch, 35 x 35 mm IC size. SF-BGA724A-B-42F female socket module can be soldered to motherboard using standard soldering methods without warping. Similarly, BGA device can be soldered to male adapter module. Both are constructed with high-temperature FR-4 substrate, assuring match with target...

Read More »
Drill Bits

Bit Inserts carry shock loads of impact drivers.

Constructed using shock-resistant tool steel and induction heat treatment that allows differential hardening of shank body, Tensor-® Bits Series can withstand impact shock loads generated by tip interface, with screw head farther down shank and away from head. Shaped shank bit inserts leverage flexural properties of steel itself to transfer load from tip to shaft, minimizing risk of bit faces...

Read More »
Drill Bits

Bit Inserts carry shock loads of impact drivers.

Constructed using shock-resistant tool steel and induction heat treatment that allows differential hardening of shank body, TensorÂ-® Bits Series can withstand impact shock loads generated by tip interface, with screw head farther down shank and away from head. Shaped shank bit inserts leverage flexural properties of steel itself to transfer load from tip to shaft, minimizing risk of bit...

Read More »
EXSYS Highlights Flexible Tooling Systems at HOUSTEX 2015
Lathes

EXSYS Highlights Flexible Tooling Systems at HOUSTEX 2015

Modular adaptors and bases provide the industry’s shortest changeover times TAMPA, Fla.- – EXSYS Tool, Inc. will showcase its well-known, high quality and innovative EXSYS/EPPINGER tooling systems at the HOUSTEX show in Houston, Texas, taking place Feb. 24-26, 2015. Exhibition visitors will discover the speed, flexibility and cost-effectiveness of such systems as PRECI-FLEX®,...

Read More »

All Topics