Kennametal Inc.    Latrobe, PA 15650
Mar 22, 2013 Combining tungsten carbide-based materials with super alloy-based technologies, UltraFlex™ provides metallurgical-bonded, void-free cladding that extends service life of critical components in demanding environments. Treatments protect base materials such as carbon and alloy steels, stainless steels, and cobalt and nickel alloys against abrasion, erosion, corrosion, and galling. Applied in thicknesses from 0.010– 0.080 in., UltraFlex conforms to intricate shapes and small internal diameters.

NKE AUSTRIA GmbH    Steyr A - 4407  Austria
Aug 13, 2012 Suited for bearings and metal parts that are exposed directly to humid or corrosive environments, SQ171E Coating provides protection against water, condensation, and slightly alkaline or acidic cleaning agents. Coating is available with silicate-based sealing layer for even more effective protection. At thickness of 4 µm, coating reaches service life of at least 96 hours without coating corrosion (white rust) or base material corrosion (red rust), in accordance with DIN 58979:2008.

Aremco Products, Inc.    Valley Cottage, NY 10989
Apr 12, 2012 Consisting of single-part, odorless, water-dispersible formula, Pyro-Paint(TM) 634-BN protects metal and refractory surfaces from corrosion by molten glass, metals, plastics, and salts in applications to 1,560°F. Non-wetting, VOC-free product is formulated with solids content of 38.6% by weight, resulting in dry film greater than 95% boron nitride with coverage rate of 345 ft²/gal, assuming 1 mil thickness. Coating dries at room temperature in 1-2 hr and cures fully in 1-2 hr at 200°F.

Aremco Products, Inc.    Valley Cottage, NY 10989
Mar 09, 2012 Applied using pneumatic spray equipment, brush, or roller, orange-pigmented Corr-Paint(TM) CP4095 provides corrosion protection and color identification on large aluminum and steel structures found in power plant, oil refining, chemical processing, and steel industries. Single-part, silicone-based, water-dispersible formula adheres to sandblasted as well as marginally prepared metal surfaces. Drying rapidly at room temperature, coating resists oxidation, UV light, humidity, and salt spray.

Henkel Corporation    Rocky Hill, CT 06067
Jan 05, 2012 Packaged in 90 mL reusable dual-cartridge dispenser, Loctite® Nordbak® 7255(TM) protects metal surfaces on industrial equipment from wear, abrasion, and corrosion. Two-part, solvent-free, thixotropic epoxy creates smooth, low-friction surfaces and may be used in overhead applications. Suitable for large surfaces and complex or intricate areas, coating can protect tank linings, mixing vessels, pump housings, impellers, chutes, troughs, and centrifuge components.

Birchwood Casey    Eden Prairie, MN 55344 2138
Jul 27, 2011 Used to replace cold blackening on iron and steel components, MICROLOK® AO coating is 1.5 microns thick, silver/black in color, and adheres tightly to metal surface. Application for this non-toxic aluminum oxide conversion coating requires 5 steps and 18 min. In addition to corrosion protection, benefits include anti-galling protection, temperature stability to 1400°F, safe 120 to 140°F operation with no boiling or splattering, and no scale or sludge buildup in tanks.

Sto Corp.    Atlanta, GA 30331
Apr 25, 2011 StoCoat® Metallic includes StoTherm® NExT EIFS for continuous insulation and also incorporates mica, metallic particles, and pigments to create look of metal surface. Available in 10 colors, product is water-based and non-toxic. It can be used on most paintable, properly primed interior or exterior surfaces, including concrete, masonry, and gypsum wallboard.

DuPont Microcircuit Materials    Research Triangle Park, NC 27709
Feb 18, 2011 Employed as paste and p-contact metallization for back side tabbing interconnects, Solamet® PV701 is formulated to maximize efficiency for Metal Wrap Through (MWT) silicon solar cell designs. Composition enables manufacture of back contact cell designs delivering up to 0.4% greater solar cell conversion efficiency. paste exhibits properties that optimize electrical contact to front side silver grid structures, mechanical strength, and solderability.

Carboline Co.    St. Louis, MO 63144
Oct 14, 2010 Suited for galvanized steel and other non-ferrous metals, water-based Galoseal WB creates tenacious bond, which optimizes topcoat adhesion to galvanized metal surfaces. Low VOC formula accepts 2-component solvent-containing finishes such as epoxies and urethanes. Product contains no heavy metals or mineral acids and provides dry film thickness of 0.5-1.0 mils.

Linetec    Wausau, WI 54402
Aug 12, 2010 Using water-based TRINAR® Aqua air dry system, Linetec provides on-site repair and restoration of architectural aluminum products' finishes. Application of fluoropolymer finish meets weathering requirements of AAMA 2605, resisting humidity, color change, chalk, gloss loss, and natural weathering. Coating also meets interior specifications for Green Seal® Standard and U.S. Green Building Council's LEED® Green Building Rating System(TM), offering low VOC content.

Birchwood Casey    Eden Prairie, MN 55344 2138
Jul 07, 2010 Suitable for most metal surfaces, including iron, steel, copper, brass, and bronze, Presto Black® Gel clings to vertical surfaces and stays where applied without forming runs or drips or bleeding onto adjoining surfaces. Product is applied at room temperature and takes 5-10 min for reaction following normal surface cleaning. Color tone and depth is controlled by visual inspection and stopping process by rinsing off with wet sponge and allowing surface to dry.

Aremco Products, Inc.    Valley Cottage, NY 10989
Aug 11, 2009 Formulated using waterborne silicate binder system filled with blend of stainless steel and ceramic corrosion inhibiting pigments, Corr-Paint(TM) CP3015-SS is suited for coating carbon steel and cast iron heat exchangers, boiler components, and exhaust headers. Single part coating system is supplied in ready-to-use viscosity of 500-1,000 cP, is applied using conventional spray equipment, and dries to typical film thickness of 2-3 mils.

Deposition Sciences, Inc.    Santa Rosa, CA 95403
Jan 26, 2009 Applied onto thin stainless steel sheets via MicroDyn® sputtering technology, High Temperature Spectral Metal Coatings withstand temperatures up to 400°C. Coated sheets can be cut and formed to specific sizes and shapes, depending on customer requirements. Mounting features, such as slots, screw holes, and tabs can be formed into mirror after coating is applied, and sized mirrors can be formed into precise curves and cylinders with radii as small as 25 mm.

Birchwood Casey    Eden Prairie, MN 55344 2138
Dec 10, 2008 LUMICLAD(TM) black oxide process is in-house method for blackening aluminum forming satin black finish on all aluminum alloys. Non-dimensional, 1.5 micron, LUMICLAD finish is tightly adherent to aluminum substrate with no ruboff. Process utilizes dip-tank procedure, without requiring electrolytic chemicals to form coating. Utilizing tank setup that operates at 70-200°F, process line is designed to operate as self-contained, zero-discharge system.

Integran Technologies Inc.    Pittsburgh, PA 15241
Nov 17, 2008 Designed to provide low frequency magnetic shielding to polymer, composite, and metal parts, Nanovate(TM) EM coating can be applied selectively, allowing shielding performance to be focused where it is needed on part. Coating can be used to stiffen and strengthen shielded polymer, composite, and metal substrates. Product suits sensors, transducers, and other applications sensitive to low frequency magnetic interference.

Aremco Products, Inc.    Valley Cottage, NY 10989
Sep 02, 2008 With low expansion, ceramic-metallic formulation that bonds well to glass and quartz halogen lamps, Quartz-Coat(TM) 845-Silver suits automotive, dental, aircraft, stadium, and fire safety industries. Product is water-based, odorless inorganic system that is silver in appearance and can absorb and evenly diffuse light at high temperatures of up to 2,000°F. It features viscosity range of 400-700 cps, solids content by volume of 42.0%, and dry film thickness of less than 1.0 mil.

Deposition Sciences, Inc.    Santa Rosa, CA 95403
May 29, 2008 Designed to maximize curing wavelengths between 220-400 nm and minimize rest of visible and IR spectrum from 450-2200 nm, UV Spectral Metal features MicroDyn® sputtering technology and is used as reflector behind curing lamp. Stable over temperature/humidity changes, it is coated onto highly polished, standard size aluminum sheets. With ability to customize/fabricate products after coating, long trough reflectors for inline exposure systems can be created using multiple lengths of product.

Cortec Corp.    St. Paul, MN 55110
May 29, 2008 Designed to replace phosphatizing and chromating systems, VpCI(TM)-440 protects multi-metal substrates from corrosion while preparing metals for surface bonding and coating. Non-toxic, non-hazardous, water-based coating can be applied with conventional equipment such as sprayers, dipping tanks, steam cleaners, and power washers. Self-preserving product is environmentally safe and does not require use of biocides.

Epner Technology, Inc.    Greenpoint, NY 11222
Apr 10, 2008 Thermal Foil Gold Coating is copper foil that is .001 in. thick, coated with Laser Gold. Laser gold plating reaches reflectivity of greater than 99% at 10 microns and greater than 98% at 1 micron. Optical coating and plating is ISO 9001:2000 certified and suited for automotive, aerospace, medical, R&D, electronic, and IR optical markets.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Apr 03, 2008 Based on titanium electrodeposited oxides, Alodine® EC2(TM) ElectroCeramic Coating provides chemical, corrosion, temperature, and abrasion resistance, extending life of parts exposed to harsh operating conditions. Product readily coats aluminum, aluminum alloys, titanium, and titanium alloys, as well as aluminized, aluminum-plated, and IVD aluminum substrates. Despite hardness of 800 vickers, coating is flexible and offers suitable base for paints, adhesives, sealants, and thermal spray coatings.