Epoxy Coatings

Adhesives & Sealants, Paints & Coatings, Materials & Material Processing

Epoxy Potting Compound resists thermal shock and cycling.

January 19, 2016

Passing Navy Hex Bar Test, MIL-I-16923C, which consists of 10 cycles from -55 to +155°C, two-part epoxy resin 20-3301 protects electronic assemblies from thermal cycling and shock. Low viscosity epoxy flows quickly around components, giving users working time of 4–6 hr. Product is typically cured at 80°C for 1–2 hr, but post cure of 150°C for 3 hr will optimize performance properties. Applications include electronic potting and encapsulating, casting, coating, and electrical varnishes. Read More

Paints & Coatings

Marine Epoxy Primer provides waterproof barrier coating.

May 22, 2015

Providing maximum resistance in both fresh and salt water, Pettit Protect® with Mica Shield Technology is suited for all exterior exposures. Heavy-duty, 2-component coating incorporates slate Mica into epoxy resin, which overlaps like shingles on roof, creating impenetrable structural barrier. In addition to osmotic blister prevention, product is formulated for tenacious adhesion making it suitable for new boats. High-solids formula also offers corrosion protection on all underwater metals. Read More

Paints & Coatings, Adhesives & Sealants

Epoxy Coating suits applications above or below water.

May 4, 2015

Based on blend of liquid epoxy polymer and aliphatic polyamine curing agents, KALCOAT™ 560 can displace water from wet surfaces to make permanent bond. High build 100% solids epoxy coating is solvent-free and incorporates Kevlar® microfibers for reinforcement and viscosity management for high application rates. KALCOAT 560 can be used as anti-corrosive coating, repair compound, fairing compound, and encapsulating coating for variety of applications. Read More

Adhesives & Sealants, Paints & Coatings

Two-Part Epoxy Paste has ultra low thermal resistance.

April 7, 2015

Master Bond EP48TC has thermal resistance of 5–7 x 10–6 K•m2/W, which enables thermal conductivity of 20–25 BTU•in/ft2•hr•°F. Applied in bond lines as thin as 10–15 microns, epoxy paste has tensile lap shear strength from 900–1,100 psi and bonds to metals, composites, glass, ceramic, and plastics. Working life for 100 gram batch at 75°F is 90–120 min. Curing at room temperature, it is serviceable over -100 to +300°F and available in ½ pint to 5 gallon containers. Read More

Paints & Coatings

Chemical-Resistant Coating protects concrete surfaces.

December 29, 2014

Protexior® Chemical Resistant Epoxy Top Coat & Primer Kit, combining Novolac epoxy protection integrated with silicone resin technology, protects insulated and un-insulated steel and concrete surfaces. Resistant to wet-dry thermal cycling, boiling water, and steam, this corrosion- and heat-resistant (up to 450°F), low-VOC coating meets ISO 20340 and ASTM B-117. Indoor/outdoor solution can be applied by roller or spray, and typical uses include piping, vessels, valves, ducts, and plenums. Read More

Paints & Coatings, Chemical Processing & Waste Management, Green & Clean, Materials & Material Processing

Silicone Curative optimizes epoxy polysiloxane topcoats.

July 8, 2014

Designed to optimize durable flexibility of epoxy polysiloxane protective topcoats in marine applications, without sacrificing weatherability, SiVance® C1008 Curative solves problems of brittleness and cracking that can develop over time as coating cures. Product is fully miscible with hydrogenated bisphenol-A epoxy resins. In addition to marine applications, C1008 is suited for coatings used on piping, bridges, wind turbines, offshore platforms, structural steel, and heavy equipment. Read More

Material Handling & Storage, Paints & Coatings

Epoxy Liner protects chemical transport tanks from corrosion.

March 26, 2014

Tested for severe chemical immersion environments, Series 391 Tank Armor consists of 100% solids epoxy liner for use in transport tanks containing chemical blends or acids used in hydraulic fracturing. Applied at 20–40 mils dry film thickness, coating contains no solvents, and is both VOC-compliant and abrasion-resistant. When spray applied in single, high-build coat by plural component equipment, it is possible to conduct high-voltage holiday testing within hours of application. Read More

Paints & Coatings, Chemical Processing & Waste Management

Autodeposition Coating suits iron castings and ferrous metals.

February 18, 2014

Formulated to deliver uniform, defect-free surface coating on both inside and outside of complex components, Bonderite® M-PP 930C™ provides corrosion and abrasion resistance, thermal stability, and edge protection. Water-based, epoxy-acrylic urethane coating will coat any surface it wets during immersion of parts with no limitation as to part size, shape, or density. Non-flammable, non-explosive, and RoHS-compliant, coating contains no toxic heavy metals, very low VOCs, and no APEs or HAPs. Read More

Adhesives & Sealants, Paints & Coatings, Chemical Processing & Waste Management, Materials & Material Processing, Services

Thermally Conductive Epoxy serves applications up to 572°F.

November 25, 2013

Used for bonding, potting, tooling, and molding, Aremco-Bond™ 805 adheres to high-temperature plastics, glass, ceramic, and high-expansion metals. This 2-component, 100% solids, aluminum-filled epoxy cures at room temperature in 24 hr with final cure at 200°F in 2 hr. Cured material exhibits thermal conductivity of 12.5 Btu-in/hr-ft²-°F and dielectric strength of 50 V/mil. Respective tensile shear and flexural strengths are 1,800 and 15,500 psi, and Shore D Hardness is 87. Read More

Adhesives & Sealants, Paints & Coatings

ESD Floor Finish enhances industrial environment safety.

August 28, 2013

Created for industrial areas and open area environments requiring static protection, EpoxyStyle ESD 2-part epoxy floor finish becomes dry to touch within 5–7 hr after application and is ready for traffic 10–12 hr after application. Chemical- and abrasion-resistant product complies with Ozone Transport Commission and California VOC regulations, may be installed over old VCT and concrete, and provides uniform matte finish; gloss can be attained when used with DuraShield ESD finish. Read More

Adhesives & Sealants, Paints & Coatings

Epoxy Adhesive/Sealant/Coating cures over 170-175°F range.

July 16, 2013

Able to cure in 20–30 min at 170 to 175°F or 10–15 min at 250°F, Supreme 3HT-80 does not require any mixing prior to use, has unlimited working life, and can be stored in conventional refrigerators. Single-component, 100% reactive system, offering optimal properties when cured at 250°F, bonds to various substrates — metals, composites, glass, ceramics, vulcanized rubbers, plastics — and does not contain any diluents or solvents. Cured system serves as electrical insulator. Read More

Paints & Coatings, Chemical Processing & Waste Management

Thermal Insulating Coatings provide safe-touch performance on hot pipes.

May 3, 2012

Formulated with Cabot's Enova® aerogel, Series 971 Aerolon Acrylic and Series 975 Aerolon Epoxy are fluid-applied, high-build coatings that respectively achieve 160 and 60 mils dry film thickness when spray-applied to piping, tanks, valves, or other steel substrates in industrial facilities. Hydrophobic formulations bond with high-performance primers for durable barrier that resists corrosion under insulation. Read More

Adhesives & Sealants, Paints & Coatings

Sprayable Ceramic Coating features reusable cartridge dispenser.

January 5, 2012

Packaged in 90 mL reusable dual-cartridge dispenser, Loctite® Nordbak® 7255(TM) protects metal surfaces on industrial equipment from wear, abrasion, and corrosion. Two-part, solvent-free, thixotropic epoxy creates smooth, low-friction surfaces and may be used in overhead applications. Suitable for large surfaces and complex or intricate areas, coating can protect tank linings, mixing vessels, pump housings, impellers, chutes, troughs, and centrifuge components. Read More

Adhesives & Sealants, Paints & Coatings

UV Curable Epoxy exhibits strength, chemical resistance.

November 22, 2011

Formulated for bonding, sealing, and coating, UV16 single-component, no-mix system cures in 1 min or less at room temperature with commercial UV light sources. This 100% reactive epoxy, uninhibited by oxygen, does not release any solvents or volatiles during cure. Cured in thicknesses up to 0.125 in. with 2%-3% shrinkage rate, solution delivers tensile strength exceeding 4,100 psi and Shore D hardness greater than 75. Product has viscosity of 200-400 cps and adheres to array of substrates. Read More

Paints & Coatings, Green & Clean

Epoxy Coating protects assets, food products, and environment.

June 13, 2011

Designed to prevent contamination when transporting and storing dry bulk food products, BPA-free CARFLEX(TM) HS meets FDA 175.300 for direct contact dry bulk storage. Polyamide-cured modified epoxy is formulated for lining rail hopper cars, storage tanks, marine vessels, and grain elevators. It offers corrosion protection and flexibility, and is impact and abrasion resistant. Applied as 1- or 2-coat system, CARFLEX HS is 100% solids, contains zero solvents, and has VOC content less than 100 g/L. Read More

Adhesives & Sealants, Paints & Coatings

Chemically Resistant Epoxy withstands one year in sulfuric acid.

March 3, 2011

Used for coating, lining, bonding, or sealing, EP21AR withstand acidic environments - including immersion in 96-98% sulfuric acid and 36% hydrochloric acid for over one year. This 2-component epoxy, with dielectric strength of 400 V/mil, also acts as electrical insulator and is serviceable from -60 to +275°F. It produces abrasion-resistant bonds with tensile strength over 10,000 psi, shear strength exceeding 2,700 psi, and compressive strength greater than 14,000 psi at 75°F. Read More

Adhesives & Sealants, Paints & Coatings

Two Component Epoxy resists fuel, acid, and agressive chemicals.

October 22, 2010

Developed for coating and lining storage tanks, piping, scrubbers, and processing equipment in chemical industry, Master Bond EP21ARHT produces bond strength greater than 2,200 psi once fully cured. Also used in electronic, electrical, and metalworking industries, product can withstand immersion in 96-98% sulfuric acid and 20% hydrochloric acid for more than 1 year. Epoxy features dielectric strength of 440 V/mil and can be thermally cycled over temperature range of -60 to +400°F. Read More

Adhesives & Sealants, Paints & Coatings

Clear Epoxy Encapsulant has pourable formulation.

November 20, 2009

Bio Clear 810(TM) is solvent free, clear epoxy used for object encapsulation (marine, electronic, and gift industries) as well as poured-on bar top and table top applications. Features include low exotherm kick, slow UV epoxy yellowing, and low viscosity, making it suited for poured applications between 1/4 and one inch thick. Bio Clear 810 has a 2:1 mix ratio. Read More

Paints & Coatings, Materials & Material Processing

Epoxy Coating checks mildew growth in damp, humid locations.

August 6, 2009

Supplied as 2-package industrial coating, Tile-Clad® High Solids Mildew Resistant epoxy protects against mildew growth on exterior surfaces where dampness and humidity are of concern. It features gloss finish and is offered in variety of safety colors. Applications include clean rooms, laboratories, institutional kitchens, and chemical processing equipment where mildew growth must be guarded against in order to maintain operations. Read More

Paints & Coatings

Epoxy Coating protects against mildew growth.

August 5, 2009

Suited for surfaces in damp, humid locations, Tile-Clad® High Solids Mildew Resistant Epoxy protects substrates such as steel, galvanizing, and concrete. Two-package coating features gloss finish and is available in variety of safety colors. Typical applications include clean rooms, laboratories, institutional kitchens, and chemical processing equipment, as well as water tank exteriors, structural and support steel, power plants, offshore structures, and fuel storage tanks. Read More