Henkel Corporation    Rocky Hill, CT 06067
Jan 05, 2012 Packaged in 90 mL reusable dual-cartridge dispenser, Loctite® Nordbak® 7255(TM) protects metal surfaces on industrial equipment from wear, abrasion, and corrosion. Two-part, solvent-free, thixotropic epoxy creates smooth, low-friction surfaces and may be used in overhead applications. Suitable for large surfaces and complex or intricate areas, coating can protect tank linings, mixing vessels, pump housings, impellers, chutes, troughs, and centrifuge components.

Aremco Products, Inc.    Valley Cottage, NY 10989
Dec 09, 2011 Consisting of single part, water-based, inorganic-ceramic coating system, Cerama-Dip(TM) 538N electrically isolates high-power ceramic resistors for applications up to 2,600°F. Odorless, VOC-free formula features volume resistivity of 109 W-cm and dielectric strength of 225 V/mil at room temperature. Applied by dipping or brushing, Cerama-Dip 538N cures by air-drying at room temperature for 1-2 hr, then step curing for 1-2 hr at 200°F and 350°F, respectively.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jun 08, 2010 Formulated for refractory and metal surfaces, jet-black, water-dispersed, HiE-Coat (TM)840-CM demonstrates emissivity greater than 0.90 at temperatures to 2,500°F. Coating is applied using sponge brush, roller, or conventional spray equipment, and offers coverage rate of 250 sq ft/gal with 2 mil dry film thickness. Curing is accomplished in operation or by heating for 1-2 hr at 200°F plus 1 hr at 500°F. Eco-friendly coating has no odor, cleans up with water, and contains no VOCs.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jan 12, 2010 Single part, water-dispersible, phosphate-bonded, and alumina-filled system, Pyro-Paint(TM) 634-ALP ceramic-based sealant is used to fill micro-porosity in dense refractory brick used in high temperature kilns and furnaces. Coating is inert, chemically resistant, inorganic, and does not outgas or decompose in corrosive applications to 3,200ºF. Available in pint, quart, gallon, and 5 gal drums, coating can be applied by brush, dip, or pneumatic sprayers, and cures fully in 1-2 hr at 700°F.

Aremco Products, Inc.    Valley Cottage, NY 10989
Aug 11, 2009 Formulated using waterborne silicate binder system filled with blend of stainless steel and ceramic corrosion inhibiting pigments, Corr-Paint(TM) CP3015-SS is suited for coating carbon steel and cast iron heat exchangers, boiler components, and exhaust headers. Single part coating system is supplied in ready-to-use viscosity of 500-1,000 cP, is applied using conventional spray equipment, and dries to typical film thickness of 2-3 mils.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jan 20, 2009 Black-pigmented, ceramic-filled Corr-Paint(TM) CP3015-BL inhibits oxidation of carbon steel and cast iron exhaust headers used in automotive, truck, and industrial applications to 1,500°F. Product is formulated using waterborne silicate binder system filled with blend of ceramic corrosion inhibiting pigments. Supplied in ready-to-use viscosity of 2,800-4,500 cp and solids of 51.5% by weight, coating is applied using spray equipment, drying to film thickness of 2-3 mils.

CerMet Lab Company    Southfield, MI 48034
Nov 19, 2008 Available in 10 ml syringes, CerMet-Auto(TM) minimizes friction in gas-powered engines. Microscopic ceramic particles are carried to engine's friction zones via engine oil, where they bond to metal surfaces, providing fuel economy benefits for approximately 60,000 miles of operation. Heat energy generated inside engine due to friction initiates ceramic coating process at atomic level, with full benefits being achieved after 2,000 miles of driving.

Aremco Products, Inc.    Valley Cottage, NY 10989
Sep 02, 2008 With low expansion, ceramic-metallic formulation that bonds well to glass and quartz halogen lamps, Quartz-Coat(TM) 845-Silver suits automotive, dental, aircraft, stadium, and fire safety industries. Product is water-based, odorless inorganic system that is silver in appearance and can absorb and evenly diffuse light at high temperatures of up to 2,000°F. It features viscosity range of 400-700 cps, solids content by volume of 42.0%, and dry film thickness of less than 1.0 mil.

Xiom Corp.    W Babylon, NY 11704
Oct 30, 2007 Designed for marine vessel hulls, Ship and Boat Bottom Coating is polymer/ceramic-based and contains no TBT or VOCs. Powder coating has evenly dispersed active copper oxide and silver ions in polymer matrix that is fully melted when applied with thermal spray process. If there should be break or tear in coating, nylon modified fuse bond epoxy between hull and coating maintains integrity. Active ingredients are strongly held and always available in coating, minimizing ablating.

Aremco Products, Inc.    Valley Cottage, NY 10989
Aug 17, 2007 Pyro-Paint(TM) 634-AS-1 is used to bond, coat, and seal refractory fiberboard used in construction of IR heaters and molten metal handling components in foundry applications to 2,300°F. Applied by brush, roller, or spray equipment, this alumina-silica based, fiber-reinforced, ceramic coating system is resistant to wetting by non-ferrous molten metals and adheres to refractory fiberboard, graphite, as well as ceramic cloth and paper. Water-based formulation contains no VOCs.

Aremco Products, Inc.    Valley Cottage, NY 10989
Aug 07, 2007 Available in pint, quart, gal, and 5 gal pails, Corr-Paint(TM) CP3015-AL, ultra-high temperature coating is used to inhibit oxidation of carbon steel and cast iron exhaust headers used in automotive, truck, and industrial applications to 1400°F. It is formulated with advanced, waterborne silicate binder system filled with blend of aluminum and ceramic corrosion inhibiting pigments. Product is supplied in ready to use viscosity of 250-450 Cp and solids of 71.0% by weight.

Aremco Products, Inc.    Valley Cottage, NY 10989
Apr 27, 2006 HiE-Coat(TM) 840-C helps improve thermal efficiency of ceramic and refractory insulated combustion and exhaust pipes as well as oven and furnace walls to 2,500°F. Demonstrating emissivity greater than 0.90, this jet-black, water-based ceramic coating will absorb and re-radiate IR energy. Cured in operation or by heating for 1-2 hr @ 200°F, environmentally friendly product is odorless and water-soluble, does not contain VOCs, and will not outgas upon curing or during operation.

Aremco Products, Inc.    Valley Cottage, NY 10989
Sep 28, 2005 As single-part, water-based, inorganic-ceramic coating system, Cerama-Dip(TM) 538N electrically insulates high-power ceramic resistors in applications to 2,600°F. Odorless, non-outgassing product contains no VOCs and features volume resistivity of 109 ohm-cm and dielectric strength of 225 V/mil at room temperature. Curing is accomplished by air-drying at room temperature for 1-2 hr then step curing for 1 or 2 hr at 200°F and 350°F, respectively.

Aremco Products, Inc.    Valley Cottage, NY 10989
May 17, 2005 Pyro-Paintâ„¢ 634-AL provides 2-part, 99% alumina filled, ceramic coating system used to bond, coat, and seal refractory fiber boards and other shapes. Material helps prevent wear and oxidation of refractory components and increases heat reflectivity. Resistant to wetting by most molten metals, product has solids content of 76.8% by weight, 66.0% by volume, and viscosity range of 5,000–6,000 cps. Water-based formulation has no VOCs and dries within 2 hr at 200°F.

Aremco Products, Inc.    Valley Cottage, NY 10989
Mar 14, 2005 Ceramacoatâ„¢ 503-VFG-C high-temperature sealant fills micro-porosity in corrosion protective, thermal spray coatings. It is formulated as single part, water-dispersible, alumina-filled system. Inert, chemically-resistant, inorganic material will not outgas or decompose in high-temperature, corrosive applications up to 3,200°F. Product is applied using sponge brush or pneumatic spray equipment. Full cure is achieved after exposure for 1-2 hr at 700°F.

ITW Devcon Futura Coatings    St. Louis, MO 63132-1021
Jan 21, 2004 Ceramic Coat® epoxy system is formulated to repair, rebuild, and protect surfaces subject to corrosion or wear, negating need for replacement parts. After reframing, damaged blades can be rebuilt to original specifications with trowelable CT 3000® and then protected with brushable Ceramic Coat 4000®. Applications include pump casings, impeller blades, suction plates, gate and butterfly valves, water boxes, tube sheets, and heat exchangers.

Aremco Products, Inc.    Valley Cottage, NY 10989
Nov 26, 2003 Pyro-Paint™ 634-AS alumina-silica-filled, fiber-reinforced, ceramic coating bonds, coats, and seals graphite and refractory materials used in molten metal fluid handling components. It also coats and insulates graphite impellers, preventing oxidation and corrosion of graphite at melt line. With 400–700 cps viscosity range, it is resistant to wetting by non-ferrous molten metals, environmentally friendly, water-based, and contains no VOCs.

Aremco Products, Inc.    Valley Cottage, NY 10989
Oct 03, 2003 Ceramacoatâ„¢ 512N high-temperature adhesive and ceramic coating system is used in assembly of ceramic, metal, and plastic electrical components and as coating of high temperature structures requiring corrosion protection. Single part, water-based, silica-filled system offers volume resistivity of 10⁹ ohm-cm and dielectric strength of 250 V/mil at room temperature. Odorless product contains no VOCs, and no outgassing will occur upon cure or during operation.

Aremco Products, Inc.    Valley Cottage, NY 10989
Aug 30, 2002 Quartz-Coatâ„¢ 845-S high temperature, sprayable, blacktop coating system has ceramic-metallic formulation that bonds to glass and quartz lighting fixtures. Single-component formulation is aqueous-based and inorganic, pigmented with deep black, temperature-stable filler. Stable in applications to 2000°F, Quartz-Coat 845-S offers viscosity range of 400–700 cps and has 42.0% solids content by volume. Post-cure coating is moisture resistant and non-outgassing.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jul 23, 2002 Ceramacoatâ„¢ 503-VFG-S ceramic-based sealant is formulated as single part, water-dispersible, alumina-filled system. Inert, chemically resistant, inorganic material does not outgas or decompose in high temperature corrosive applications to 3200°F. Applied using sponge brush or pneumatic spray equipment, full cure is achieved after exposure for 1-2 hours at 700°F. It sinters and strengthens as exposed to temperatures above 1000°F.