Whitford Corp.    Elverson, PA 19520
Mar 07, 2011 Offering alternative to PFA powder, Xylan HB Waterborne Fluoropolymer Coatings provide optimal release characteristics. Products can be applied at films to 75 microns thick with one cure and up to 125 microns with longer-than-normal cure cycles. With ability to form thick films, coatings offer extended wear characteristics and are suitable for applications with rough surfaces, from commercial waffle irons to molds that are recycled repeatedly. All are FDA-compliant.

Master Bond, Inc.    Hackensack, NJ 07601
Mar 03, 2011 Used for coating, lining, bonding, or sealing, EP21AR withstand acidic environments - including immersion in 96-98% sulfuric acid and 36% hydrochloric acid for over one year. This 2-component epoxy, with dielectric strength of 400 V/mil, also acts as electrical insulator and is serviceable from -60 to +275°F. It produces abrasion-resistant bonds with tensile strength over 10,000 psi, shear strength exceeding 2,700 psi, and compressive strength greater than 14,000 psi at 75°F.

Slip Resistant Solutions, Inc.    Oldsmar, FL 34677
Mar 03, 2011 Slip Resistant Solutions for Porcelain Bathtubs, packaged in 1 gal container, treats 30-40 bathtubs. It creates microscopic tread pattern in bathtub porcelain surface without any aesthetically discernible difference. Tread pattern raises coefficient of friction, promoting slip resistance. Treatment does not change bathtub cleaning process and takes 5 minutes to complete. Areas of use include hotels, nursing facilities, and other places with multiple porcelain bathtubs.

Birchwood Casey    Eden Prairie, MN 55344 2138
Mar 01, 2011 Utilizing Ion Exchange technology to remove all particulates and dissolved ions from rinse waters, LUMICLAD® features Zero-Discharge configuration that totally eliminates need for drain connection. System produces 1.5 micron thick satin black finish with smooth, clean surface that is electrically conductive and tightly adherent to aluminum substrate. Finish can be applied to all aluminum alloys, with no reduction in hole diameters or change in critical dimensions.

Honeywell International, Inc.    Morristown, NJ 07960
Mar 01, 2011 SOLARC® anti-reflective coating materials are applied through single-sided roller coating application, which reduces amount of material required. Transparent coatings also improve light transmittance through glass that covers photovoltaic panels and minimize glare, which enables panels to better blend in with surroundings. Suited for PV panels that operate from 350-1,100 nm, coating materials also enable panels to withstand harsh environmental conditions.

DuPont Microcircuit Materials    Research Triangle Park, NC 27709
Feb 18, 2011 Employed as paste and p-contact metallization for back side tabbing interconnects, Solamet® PV701 is formulated to maximize efficiency for Metal Wrap Through (MWT) silicon solar cell designs. Composition enables manufacture of back contact cell designs delivering up to 0.4% greater solar cell conversion efficiency. paste exhibits properties that optimize electrical contact to front side silver grid structures, mechanical strength, and solderability.

Chromalloy Research & Technology Div.    Orangeburg, NY 10962
Feb 04, 2011 To enhance performance of gas turbine engines, RT-35 Low K coating provides layer of insulation to base metal component and underlying bond coating surface of turbine blade. It protects against heat of combustion gases experienced during engine operation. Lower thermal conductivity allows engines to perform at higher temperatures, and coating also increases resistance to oxidation and corrosion of underlying bond coating.

Interplastic Corp.    St. Paul, MN 55110
Feb 01, 2011 Integrity(TM) High Performance Gel Coatings are formulated with high performance polymers, fillers, and light stabilizers that provide UV resistance, color and gloss retention, water resistance, and crack resistance. They are easy to spray on and resist sagging and weathering. Integrity gel coat meets EPA Maximum Achievable Control Technology (MACT) standards for composites manufacturing.

Antistatic Industries    Northvale, NJ 07647
Jan 25, 2011 Available in white and off white, Static Paint® resists oils, grease, foodstuffs, and detergents. Two-part epoxy system is water-resistant upon drying and can be applied by brush or spray. Supplied in 1 and 5 gallon kits, paint can be used on walls, floors, steel handles, railings, and various equipment used in food processing plants, restaurants, hospitals, schools, warehouse facilities, labs, or anywhere FDA-compliant antistatic paint for direct food contact is necessary.

APV Engineered Coatings    Akron, OH 44301
Jan 25, 2011 Comprised of Kynar Aquatec® resin-based topcoat and elastomeric acrylic basecoat, APV eCoolRoof(TM) optimizes emissivity and total solar reflectance properties of roof's surface. Low VOC product resists UV ray degradation, chalking, water pickup, dirt pickup, staining, and chemicals as well as corrosion, algae, and fungal growth. Field-applied and air dried, APV eCoolRoof meets or exceeds initial Cool Roof Rating Council requirements to reflect sunlight and heat away from structure.

Abrisa Industrial Glass, Inc.    Santa Paula, CA 93060
Jan 21, 2011 Suited for outdoor use or environments where moisture is present, hydrophilic coatings reduce distortion by interacting positively with water and causing condensates to spread uniformly over surface of coated glass. They comply with MIL-C-675C for severe abrasion and can be applied on glass substrates for optics applications with wavelengths from 350-2,700 nm. Available as coated and laminated solutions, hydrophobic coatings create barrier against dirt, dust, and liquids.

Abrisa Industrial Glass, Inc.    Santa Paula, CA 93060
Jan 21, 2011 Indium Tin Oxide (ITO) and Index-Matched Indium Tin Oxide (IMITO) coatings are optically transparent and can be applied to various technical and commercial glass substrates. Able to be designed with sheet resistances below 5 ohms per square, IMITO solutions inhibit effects of EMI, RFI, and ESD. By using ITO coating, EMI, RFI, and ESD are minimized and may be virtually eliminated. Coatings are resistant to flaking, peeling, cracking, delaminating, and crazing.

LPS Laboratories, Inc., An Illinois Tool Works Co.    Tucker, GA 30085-5052
Jan 20, 2011 Protecting against seizure, heat-freeze, galling, rust, and corrosion, Food Grade Anti-Seize is NSF® Certified H1: Registration No. 143035 for use in food plants and conforms to FDA Regulation 21 CFR 178.3570 for incidental food contact. It has -65 to +1,800°F service rating and is not affected by metal contraction, expansion, or vibration. Non-staining and odorless, this product contains no metals, may be used with potable water, and meets MIL-PRF-907E.

DEK    Rolling Meadows, IL 60006
Jan 19, 2011 Incorporating six-sigma repeatability and parallel print head processing options that maximize uptime, Eclipse photovoltaic (PV) metallization platform offers integrated vision inspection and master controls. Retrofittable modules enable manufacturers to scale production to 1,200, 2,400, or 3,600 wafers per hour (wph). Performance can be upgraded in field; spacer process modules can be deployed at initial installation then exchanged for additional print capacity.

Sherwin-Williams Co. c/o Ultimate Lead Systems    Berea, OH 44017
Dec 17, 2010 Suited for tank linings and piping under insulation, Cor-Cote® HT FF contains micaceous iron oxide for anti-corrosion and edge protective properties. Epoxy novolac amine is resistant up to 450°F in dry service environment and will perform in areas subject to wet/dry cycling up to 300°F. Available in 3 shades of gray, product can be applied to steel, stainless steel, or concrete and is designed for service with gasoline, fuel oil, diesel fuel, crude oil, ethanol, and other hydrocarbons.

Master Bond, Inc.    Hackensack, NJ 07601
Dec 15, 2010 With thermal conductivity over 22 BTU/in/ft²/hr/°F and serviceability from -60 to +400°F, EP21ANHT helps mitigate issues associated with tightly packed components and miniaturized electronic circuits. This 2-component adhesive, sealant, and coating has 1:1 mix ratio by weight or volume and cures at room or elevated temperatures. Also able to act as electrical insulator, cured adhesive exhibits dielectric strength over 400 V/mil and tensile shear strength over 1,000 psi.

Rhino Linings USA    San Diego, CA 92121
Dec 09, 2010 Rhino(TM) Eco-Coat(TM) helps to reflect sunlight off roof and to improve energy efficiency of building. Aromatic, zero VOC, spray-applied coating for commercial and industrial roofs contains UV stabilizers and leafing aluminum pigment for UV stability. High tensile strength and abrasion resistance enables 2-component product to resist hail, mechanical impact, and pest infestations. It can be used as top coat over Rhino(TM) SPF or as coating for primed metal or concrete roofs.

Birchwood Casey    Eden Prairie, MN 55344 2138
Dec 03, 2010 Utilizing Ion Exchange technology to purify and recycle rinse waters, TRU TEMP® System provides closed-loop, zero-discharge installation, eliminating need for drain connection. System operates at 200°F to avoid hazards of boiling tank and is safe to install in any area of plant. In 30 minutes, system forms .00020 in. thick black magnetite finish. TRU TEMP 100-gallon line utilizes 7 individual tanks, each measuring 24 x 40 x 28 in., and can process up to 4,000 lb of work/shift.

Masterchem Industries, Inc.    Imperial, MO 63052
Dec 02, 2010 Fast drying KILZ® Masonry and Stucco primer can be used on recently poured masonry and stucco surfaces. It penetrates and binds light surface chalk, creating surface that is ready to be top coated, and is suited for use with interior and exterior above-grade masonry, stucco, plasters, and poured and precast concrete. Available in 5 gal containers, clear primer is 100% styrene acrylic, is alkali-resistant up to 13.0 pH, and lowers risk of lime burn, discoloration, and efflorescence.

Epoxies Etc.    Cranston, RI 02921-3407
Dec 01, 2010 Designed to cure at room temperature, 2-component 20-2125 Potting, Encapsulating, and Casting Resin cushions and protects sensitive electronic components while imparting very little stress on components during cure or thermal cycling. Hardness can be modified by changing mix ratio of Polyol and Isocyanate. Moisture-resistant with low toxicity, product can be used in wet environments and minimizes employee exposure to dangerous chemicals.