Sentinel Chemical Co., Inc.    Minneapolis, MN 55432 2512
May 06, 2003 Self-priming 24/7 Coating with Microban® Antimicrobial Product Protection inhibits growth of odor and stain-causing bacteria, mold, and mildew on coating film. Microban additives are EPA registered and will last life of coating by guarding against degradation caused by microorganisms. Coating cleans up with soap and water and is suitable for lined and unlined HVAC duct systems, previously painted surfaces, drywall plaster, wood, concrete, brick, and most metal.

Chemco Mfg. Co., Inc.    Northbrook, IL 60062 1920
May 01, 2003 Fast-Dry Peelable Coating is free of both VOCs and heavy metals. Single-component, non-flammable liquid coating is virtually odor-free and can be applied to metals, plastics, glass, and any other nonporous material using standard spray equipment. It is also applicable via brush and can be used as edge protector. Product complies with OSHA regulations and has reflective white surface that enhances brightness within work area.

Revere Products    Cleveland, OH 44135 0311
Apr 21, 2003 ELASTI-GARD® System consists of 3 components: ELASTI-GARD Primer for rusted areas to prevent further corrosion; Flexible Cement to seal fasteners, flashings and seams; and ELASTI-GARD Coating to seal system. It dries quickly and stretches as metal roofs move without breaking or splitting. System retains flexibility, even under severe weather conditions and extreme temperature changes. Coating has highly reflective finish and meets National VOC Emission Standards.

Balzers, Inc.    Elgin, IL 60123
Apr 17, 2003 BALINIT® ENDURA offers optimization potential with turning and milling tools in highly abrasive applications. High metal removal rates can be realized by cutting with high speed and feed rates simultaneously. Coating provides protection against abrasive wear. Ratio of residual compressive stress to hardness stabilizes tool cutting edge under high loads, and increased thickness reduces heat transfer to tool and offers protection against cratering.

Sherwin-Williams Co.    Cleveland, OH 44115
Apr 16, 2003 Fast Glo Acrylic Safety Marking Paint is single component acrylic with phosphorescent luminescent pigment that enables paint to glow yellow/green in dark for up to 4 hours. Paint is for marking aisle ways, emergency routes, boundaries, and stairways to identify safe passageways in event of power outage or failure of back-up power systems. It can be applied by brush, roll, or spray and comes in quart and gallon containers.

Columbia Marking Tools, Inc.    Chesterfield, MI 48047
Apr 10, 2003 ACC(TM) Auto Clean, chemically applied electroless nickel coating, provides lubricity of Teflon® to eliminate effects of rust on stamp characters and stamp retainers. Product also aids in preventing dirt from compacting into individual stamp characters, thereby avoiding character blow out and deterioration of stamp characters that might lead to chipping and loss of stamp integrity.

Sherwin-Williams Co.    Cleveland, OH 44115
Apr 08, 2003 ControlTechâ„¢ coatings include 26 low-VOC coatings engineered for use on concrete or steel tanks, floors, drains, clarifiers, sumps, and slabs. Products consists of thin film and medium film systems; laminates such as single, double, and flexible basecoat systems; mortar and mortar laminate systems; and EnviroLastic Polyurea coating systems for potable water, concrete, steel, geotextile and repair applications.

Master Chemical Corporation    Perrysburg, OH 43552
Apr 03, 2003 Semisynthetic TRIM® SC285 cutting and grinding fluid concentrate is for extreme-pressure lubrication in drilling, tapping, reaming, and form-grinding operations. Product leaves synthetic-oil film that protects ferrous and nonferrous metal parts. It is safe for steel alloys, cast iron, and copper alloys. Lubricant does not contain chlorine or sulfur-based EP additives, DEA, nitrides, phenolic compounds, or formaldehyde releasers.

Masterchem Industries, Inc.    Barnhart, MO 63012
Mar 20, 2003 Hammerite® RustCapâ„¢ can be painted directly over firm, rusty surfaces such as iron and steel, providing decorative finish that is resistant to corrosion and damaging effects of moisture and severe weather. As coating dries, heat-hardened glass flakes interlock with resins to form surface of protective resin and glass particles, inhibiting growth or continuation of rust. Product dries to touch in 30–45 min.

Chemetall Oakite Products, Inc.    Berkeley Heights, NJ 07922 2712
Mar 11, 2003 Gardobond A 4920 liquid pretreatment replaces conventional treatments on steel and offers reduced operating temperatures as low as 80°F. It provides salt-spray protection with wide variety of paints, resulting in longer life for finished part. Agent is non-toxic, contains no heavy metals, and is environmentally compliant.

NYLOK Corp.    Macomb, MI 48042 4007
Mar 05, 2003 Fused-On Powder Coatings prevent metal-to-metal contact, provide wear resistance, and protect against rust. Epoxy powder is applied by electrostatic spray or fluidized bed and cured in convection ovens. Nylon 11 and 12 powders are applied by electrostatic spray and cured by post heating induction process. Nylon 11 prevents galvanic corrosion between dissimilar materials, while thick coating of epoxy powder can be used on sharp metal parts to prevent cutting.

Acton Research Corp.    Acton, MA 01720
Feb 14, 2003 No. 3000-SI Al+SiO2 optical coating is optimized for maximum UV reflectance with greater than 89% reflectance from 250–300 nm, and broadband reflectance of 200–700 nm. Coating survives mil-spec adhesion and temp/humidity cycling and is more durable than conventional UV Al+MgF2 coatings. It is suited for N2 laser use and for analytical applications that require stability and UV-VIS reflectance. Coating can be cleaned using recommended solvents and procedures.

Dynisco Instruments    Franklin, MA 02038
Feb 06, 2003 Oil filled pressure transducers, suited for food and medical extrusion markets, meet FDA requirements 21 CFR 178.3620, 21 CFR 172.878, and 21 CFR 573.680 as well as H1 status from USDA. DyMaxâ„¢ proprietary coating for melt pressure transducer diaphragms adds abrasion resistance without limiting performance. Product does not add to thickness of machined, high-grade stainless steel transducer diaphragms or negatively impact sensitivity.

Balzers, Inc.    Elgin, IL 60123
Jan 13, 2003 Diamond-like BALINIT® TRITON, for machining aluminum alloys and other non-ferrous metals, has hardness rating of over 2,500 HV 0.05 and low coefficient of friction (against dry steel: 0.1 to 0.2). With temperatures up to 660°F at cutting edge, adhesion-reducing properties of product prevent material adherence to tool. Coating is suitable for drilling, reaming, milling, turning, recessing, and tapping applications, and also suits polycarbonates, and other plastic materials.

Integument Technologies, Inc.    Tonawanda, NY 14150-6711
Jan 06, 2003 FluoroGripâ„¢ linings are made of DuPont Teflon® and offered in rolls of film offering peel-and-stick installation. They have no VOCs or hazardous solvents, making them safe to apply over various substrates including steel and metals. Linings offer chemical resistance to withstand repeated cleanings. They remain effective over expanding, contracting, and flexing substrates. Applications include kitchens, showers-restrooms, and crew living quarters on ships.

Garon Products, Inc.    Wall, NJ 07719 1924
Jan 02, 2003 POUR-N-WALKâ„¢ 100% solids, epoxy strength floor resurfacer provides glossy, uniform surface that is virtually impervious to dirt and bacteria. Self-leveling product withstands impact and thermal shock of high traffic. User can mix, pour, and finish with notched squeegee; no topcoat is needed.

Rez-Solutions    Lakewood, NJ 08701
Dec 03, 2002 Two-component, 100% solids, pigmented, polyurethane-base Soft Floor Systems are suitable for balconies, ramps, locker rooms, hospitals, and skating rinks. Soft Floor 6000 is topped with polyurethane or pigmented Polyurea. It can be applied between 10 and 250 mils in one pass without bubbling due to out gassing. Soft Flake 6001 is broadcast with colored vinyl flakes and top coated with clear urethane. Soft Grip 6002 is broadcast with pigmented rubber fines for non-skid safety surface.

Aremco Products, Inc.    Valley Cottage, NY 10989
Dec 02, 2002 Corr-Paintâ„¢ CP4020 gray-pigmented coating seals and protects steel components and structures in applications up to 1100°F. Single-part, silicone based, water-dispersible coating system adheres to sandblasted and marginally prepared surfaces. Product dries at room temperature, curing as coated structure achieves operating temperature. Resultant coating is color stable and resistant to oxidation, ultra-violet light, humidity, and salt spray conditions.

Rez-Solutions    Lakewood, NJ 08701
Nov 26, 2002 Based on pure polyurea, Tough-Cote URC, Tough-Cote URM, and Tough-Cote URR are seamless, flexible coatings that offer water- and chemical-resistance. Products are 100% solids, 2-component, pure polyurea elastomers, and can be applied at temperatures from –40 to +350°F. Coatings, formulated with UV stabilizers, can be applied to metal and roofing substrates, including concrete, foam, and wood.

Sherwin-Williams Co.    Cleveland, OH 44115
Nov 22, 2002 High-build, fast-drying, direct-to-metal Fast Cladâ„¢ DTM Urethane can be applied at 6–9 mils DFT in single coat with no outgassing or pinholing. Urethane dries in 1 hour as corrosion-resistant finish and may be applied at temperatures as low as 35°F, with airless spray equipment, brush, or roller. Coating has 2-hour potlife at 77°F and is for use directly over properly prepared steel.