McLube Div., McGee Industries, Inc.    Aston, PA 19014
Jan 19, 2012 Intended for rubber and plastic parts, water-based MAC-1023 dries to clear, colorless film with optimum slip properties and minimal coefficient of friction. Coating is chemically and thermally stable as well as environmentally and worker friendly. In addition to rubber and plastic, product is also suitable for use on composite, sponge, and all types of metal. Applications include automotive assembly, O-rings, seals, bushings, hoses, and grommets.

McLube Div., McGee Industries, Inc.    Aston, PA 19014
Jan 18, 2012 Used for release of rubber and plastic parts, water-based MAC-678 is supplied as concentrate that can be diluted with normal plant water. Product can be applied highly diluted as touch-up spray or lightly diluted as semi-permanent release coating. Durable release film bonds to applied surface, allowing for multiple release cycles with no transfer to molded part. Able to work with various parts and compounds, agent is thermally and chemically stable with shelf life of 1 year.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jan 10, 2012 Suitable for industrial applications to 500°F, Corr-Paint(TM) CP2060 adheres to marginally prepared metal surfaces and resists wide range of chemicals, including acetic acid, jet fuel, alcohols, diesel fuel, gasoline, and hydrochloric acid. Two part, silicon carbide filled, 100% solids, epoxy-novolac coating is both abrasion and corrosion resistant. Packaged in pre-weighed kits for 100:8 mix ratio by weight, product sets and cures fully at room temperature in 24 hr.

Henkel Corporation    Rocky Hill, CT 06067
Jan 05, 2012 Packaged in 90 mL reusable dual-cartridge dispenser, Loctite® Nordbak® 7255(TM) protects metal surfaces on industrial equipment from wear, abrasion, and corrosion. Two-part, solvent-free, thixotropic epoxy creates smooth, low-friction surfaces and may be used in overhead applications. Suitable for large surfaces and complex or intricate areas, coating can protect tank linings, mixing vessels, pump housings, impellers, chutes, troughs, and centrifuge components.

Birchwood Casey    Eden Prairie, MN 55344 2138
Dec 22, 2011 Forming protective, non-dimensional black oxide finish on all aluminum surfaces, LUMICLAD® is tightly adherent to metal substrate and is suitable for flat buttons, t-nuts, fluid connections, eye bolts, hex nuts, and handles. System utilizes conventional immersion tank process line and contains no EPA-regulated chemicals. Achieving uniform coating thickness of .00060 in., LUMICLAD will not close down hole diameters or change/clog thread dimensions.

Aremco Products, Inc.    Valley Cottage, NY 10989
Dec 09, 2011 Consisting of single part, water-based, inorganic-ceramic coating system, Cerama-Dip(TM) 538N electrically isolates high-power ceramic resistors for applications up to 2,600°F. Odorless, VOC-free formula features volume resistivity of 109 W-cm and dielectric strength of 225 V/mil at room temperature. Applied by dipping or brushing, Cerama-Dip 538N cures by air-drying at room temperature for 1-2 hr, then step curing for 1-2 hr at 200°F and 350°F, respectively.

Aremco Products, Inc.    Valley Cottage, NY 10989
Dec 06, 2011 Based on titanium diboride, Graphi-Coat(TM) 623 inhibits oxidation of most commercial grades of graphite to 2,000°F. Two-part, water-based, non-volatile material is applied using brush, roller, dip- or spray-processing. Typically air set for 1-2 hr at ambient temperature then cured in-situ or in 10-15 min at 1,300°F, coating protects graphite crucibles and fixtures used in metallurgical casting processes as well as graphite electrodes used in arc-melting furnaces.

Crown Polymers, LLC    Huntley, IL 60142
Dec 05, 2011 Formulated to cover unsightly flaws in concrete while becoming monolithic part of concrete, StainedGlaze(TM) is nearly odorless during application, contains no harmful VOCs, and exceeds sustainability Green requirements for LEED® certification. Wear surface, colors, designs, and patterns are renewable without removing entire overlay. Typical applications include dining areas and restrooms as well as commercial, retail, residential, educational, and light industrial locations.

Ellsworth Adhesives    Germantown, WI 53022
Dec 01, 2011 Engineered to cure with UV and visible light using broad spectrum and LED curing equipment, E-MAX 903-E also features secondary moisture-cure mechanism for ambient cure in shadowed areas. Product offers tack-free cure immediately upon cooling after light exposure. Coating is available in 30 mL syringes, 1 L bottles, and 5 gal cans.

Birchwood Casey    Eden Prairie, MN 55344 2138
Nov 29, 2011 Accommodating manufacturers that require same-day black finishing of small lots, mini BK-LC products enable safe, in-house blackening of parts and achieve durable satin black finish. LUMICLAD® process, which utilizes one heated dip-tank and does not require electrolytic current, forms black oxide coating on aluminum. Process works on all cast and wrought aluminum alloys, forming smooth, black, 1.5 micron thick finish that adheres tightly to aluminum substrate without any rub-off.

Master Bond, Inc.    Hackensack, NJ 07601
Nov 22, 2011 Formulated for bonding, sealing, and coating, UV16 single-component, no-mix system cures in 1 min or less at room temperature with commercial UV light sources. This 100% reactive epoxy, uninhibited by oxygen, does not release any solvents or volatiles during cure. Cured in thicknesses up to 0.125 in. with 2%-3% shrinkage rate, solution delivers tensile strength exceeding 4,100 psi and Shore D hardness greater than 75. Product has viscosity of 200-400 cps and adheres to array of substrates.

Huron Technologies, Inc.    Leslie, MI 49251
Nov 02, 2011 Targeting manufacturers of compression molded fluoroelastomers, Release Coating 7463 provides release of rubber seals, gaskets, O-rings, grommets, and other molded parts. Product is designed for use at molding temperatures from 290-400°F and can release intricate rubber shapes without pulling or tearing. Successfully tested with tetrafluoroethylene-propylene and fluoropolymer elastomers, agent also reduces mold buildup and decreases frequency of requisite mold cleanings.

Bayer MaterialScience, LLC - Coatings, Adhesives & Sealants    Pittsburgh, PA 15205
Oct 14, 2011 Used for restoring water slides, polyaspartic gelcoat technology has life expectancy of years and dry times that accelerate return-to-service - sometimes as soon as 24 hr. Low-odor product is formulated for optimal durability, weather-ability, color and gloss retention, and ultra-low VOC content. This spray-applied, 2-component, ambient-cure gelcoat also has temperature application range that extends season for restoring outdoor slides.

UVolve® Instant Floor Coatings    Elgin, IL 60120
Oct 12, 2011 Registered for incidental food contact, UVolve® Instant Floor Coatings provide sustainable solution for food and beverage facilities. Immediate UV cure accelerates return to service after application, minimizing impact on business operations. Once installed, low-odor and nero-zero VOC emissions solution produces floors with anti-slip finish as well as chemical and stain resistance. Dirt and debris will not penetrate protective surface, facilitating sanitization.

Michelman Inc.    Cincinnati, OH 45236
Oct 06, 2011 FDA-compliant Michem Coat 40Y provides barrier coating for paper and corrugated. Combination of raw materials and proprietary formulation techniques are used to produce coating that is resistant to water, oil, and grease and has optimized release properties. Completely repulpable and recyclable, this hot melt and coldset gluable product maintains stability and can be applied smoothly on rod, blade, or roll coaters either inline or offline.

Dymax Corp.    Torrington, CT 06790
Oct 04, 2011 Engineered for circuit protection in coating applications that require ambient shadowed area cure, solvent-free 9481-E offers secondary moisture curing rate that ensures cure on all areas of board without heat or additional processing. Viscosity facilitates application of desired coating thicknesses, while fluorescing aids inspection of thin layers and component edges. Tack-free immediately after cooling, product is also resistant to chemicals.

Color Wheel Paints & Coatings    Orlando, FL 32808
Oct 04, 2011 To create base coat that promotes efficient use of finish coat, 1260 Flex Lox Surface Sealer is formulated for optimal adhesion, chalk-binding, and sealing as well as hiding capability. Primer is designed for previously painted surfaces and uses acrylic resins to penetrate and seal substrate. With properties that promote topcoat adhesion, low-odor solution meets LEED standard for low VOC (less than 50 g/L) and is designed as companion primer for use with Flex Lox Flat and Satin.

Michelman Inc.    Cincinnati, OH 45236
Oct 04, 2011 Using advanced raw materials, Michem Coat 40Y is water, oil, and grease resistant with optimized release properties. Product is also hot melt and coldset gluable, and completely repulpable and recyclable. Compliant with FDA standards, Michem Coat 40Y is suited for food contact with items such as produce and other perishables, as well as general industrial and retail applications. Product can be applied smoothly on rod, blade, or roll coaters, either inline or offline.

McLube Div., McGee Industries, Inc.    Aston, PA 19014
Sep 23, 2011 Available as 25%, 15%, and 5% dispersions in isopropyl alcohol (IPA), McLube PTFE (polytetrafluoroethylene) Dry Film Dispersions provide low coefficient of friction and have average particle size of less than 10 microns. Products are chemically inert and can can be applied to metal, plastic, rubber, leather, and fabric surfaces. Thermally stable to 6,150°F, dispersions are supplied as concentrates and may be used as dry film lubricants, mold release agents, and antistick coatings.

Sherwin-Williams Co. c/o Ultimate Lead Systems    Berea, OH 44017
Aug 31, 2011 Offered as 2-component solution, 3425E Static Control Water-Based Epoxy Coating may be used as coating or topcoat over standard flooring systems to provide static dissipative flooring system in range of 106-109 ohms resistance. It provides resistance to wear, abrasion, and chemical attack from common alkalis and acids and can also be used as conductive coating in range of 25,000-106 ohms resistance when applied over 3424 Conductive Water-Based Epoxy Primer.