Corning Cable Systems
Hickory, NC 28603-0489
Jul 08, 2008 Able to be installed in less than 1 min through use of mechanical splice technology, OptiSnap(TM) Connector accelerates termination of fiber optic cables in CATV deployments. This no-epoxy, no-polish connector is available in single-mode SC, ST, and LC connector styles and features typical insertion loss of 0.2 dB (UPC versions) and 0.4 dB (APC versions). Installation system has on-tool go/no-go feedback signal to confirm correct installation.

Nokia Siemens Networks
Espoo 02610  Finland
Jul 02, 2008 With multi-service and multi-reach feature set, hiT 7300 supports all reaches and transmission speeds in metro, regional, long-haul, and ultra-long haul applications on single platform. Unit has transponder cards that support traditional SONET/SDH, Ethernet, and SAN services at different speeds. Including amplifier options and end-to-end management support for all equipment configurations, it is also available in flatpack form factor suitable as CPE for tight space requirements.

Timbercon, Inc.
Lake Oswego, OR 97035
Jul 01, 2008 Standard single mode coupler/splitters are used to either combine 2 or more signals into 1 or split 1 signal into multiple paths. They come in 1 x 2, 1 x 3, 1 x 4, 1 x 8, 1 x 16, 1 x 32, 2 x 2, and 2 x 4 configurations with LC, SC, FC, and ST fiber optic connectors and polishes. Each unit is offered in either ruggedized plastic housing with 3 mm leads or low profile stainless steel tube for high density equipment requirements.

GigOptix
Palo Alto, CA 94303
Jun 25, 2008 Model HXT4104 is 4-channel 10.3 Gbps Vertical Cavity Surface Emitting Laser (VCSEL) driver that can drive 10 mA average and 8 mA modulation current, and dissipates 91 mW of power per channel. Parallel VCSEL driver is digitally programmable via industry standard 2-wire interface, enabling control of signal peaking, modulation, and average current, in addition to providing access to temperature and output power monitoring on channel by channel basis.

Exar Corp.
Fremont, CA 94538
Jun 24, 2008 Requiring 1.62 V, XR16MXX4 series is comprised of 6 devices featuring 4 independent UART channels, selectable TX and RX trigger levels, and data rates up to 16 Mbps. Specific versions - XR16M564/564D and XR16M654/654D - also incorporate automatic sleep mode, hardware flow control, and software flow control; wireless IR encoder/decoder; and fractional baud rate generator. Each series member supports Intel and Motorola bus interfaces.

Galazar Networks, Inc.
Ontario K2H 1E6  Canada
Jun 20, 2008 Suited for ROADM/DWDM applications, MXP(TM) devices address metro networking applications by combining Next-Gen SONET/SDH functions of MSPP and OTN functions of transponder to act as muxponder-on-a-chip. This helps Service Providers utilize their WDM wavelengths more efficiently by allowing them to multiplex number of revenue-generating services on single wavelength. Muxponder cards based on MXP family can address all service types, including Ethernet, SONET/SDH, SAN, and Video.

Toshiba America Electronic Components (TAEC)
Irvine, CA 92618-1811
Jun 16, 2008 Housed in 6-pin SDIP package that meets insulation requirements of international safety standards, Model TLP700 features ±2.0 A peak output current, 2 mA supply current, and 5,000 Vrms isolation voltage. Unit consists of integrated photodetector optically coupled to gallium-aluminum-arsenide LED in package measuring 6.8 x 7.62 x 3.65 mm. Operating from -40 to 100°C, device is suited for factory automation equipment, robots, general-purpose inverters, and ac servo motor control.

Phoenix Contact
Harrisburg, PA 17111 0100
Jun 13, 2008 Designed for industrial Ethernet and PROFINET applications, VARIOSUB Push-Pull plug connector system enables transmission of data and power signals directly to local devices. It comes in 3 versions: RJ45 for copper data transmission, SCRJ for fiber optic data transmission, and COMBICON device connection technology for power transmission. Available in metal and plastic, connectors can be operated with one hand, simplifying network installation.

Avago Technologies
San Jose, CA 95131
Jun 13, 2008 Complying with automotive AEC-Q100 guidelines, ACPL-312T provides 2.5 A max peak output current to drive high powered IGBTs/MOSFETs and operates in temperatures from -40°C to +125°C. Propagation delay of 0.5 µsec allows circuit designer to reduce switching dead time and improve inverter efficiency. It offers min CMR of 25 kV/µsec at VCM = 1,500 V for noise elimination and undervoltage lockout for additional protection.

Avago Technologies
San Jose, CA 95131
Jun 13, 2008 Supporting industry's temperature range of -40°C to +105°C, ACPL-071L, ACPL-074L, and ACPL-M75L high-speed dual-supply voltage digital CMOS optocouplers operate in +3.3 V and +5 V supply voltages at minimum speed of 15 MBd. Single channel ACPL-071L/M75L and dual channel ACPL 074L can prevent any output disruption in case of power supply loss or recovery. Available in SO-5 and SO-8 packaging, units are IEC/EN/DIN EN 60747-5-2, UL1577, and CSA compliant for reinforced insulation.

Avago Technologies
San Jose, CA 95131
Jun 13, 2008 Featuring 2.5 A maximum peak output current, ACPL-K312 gate drive optocoupler offers fast IGBT switching, making it suitable for IGBT/MOSFET gate drives, ac/brushless dc motor drives, industrial inverters, and switching power supplies. Supporting operating temperature range of -40 to +100°C, CSA approved unit offers low power consumption with Icc of 3.0 mA and CMR of 15 kV/ms at Vcm = 1.5 kV. Undervoltage lockout prevents undesired IGBT turn-on which can lead to long term damage.

3M Company / Electronic Products Division
Austin, TX 78769
Jun 05, 2008 Designed for analog video applications, No Polish Connector SC/APC is pre-assembled to speed on-site installation of 250 and 900 micron connections. Solution features factory-polished ferrule assembly and can be installed with field tool in under 2 min. Keyed angle cleave mechanical splice feature minimizes connection gap while maximizing optical reflection performance. This results in back reflection of under -60 dB across temperature range.

Qualcomm, Inc.
San Diego, CA 92121
Jun 03, 2008 Supplied in 3.2 x 2.9 mm CSP, BTS4025(TM) SoC offers up to +13 dBm transmit power through integration of on-chip power amplifier to enhance connection reliability and range between Bluetooth device pairs. Product offers full support for Bluetooth 2.1 + Enhanced Data Rate specification, requires minimal external components, and can use existing system clock. To extend battery life, SoC reduces standby current consumption up to 50% when device is scanning for other Bluetooth devices.

Fairchild Semiconductor
San Jose, CA 95134
May 21, 2008 With built-in active dv/dt clamp that provides noise immunity (dv/dt) of 10,000 V/µs, random-phase FOD420 and FOD4208 facilitate solid state relay, AC motor control, and lighting ballast design. RoHS-compliant products provide 5,000 V of isolation while controlling power triacs that switch load. They utilize Pb-free terminals and can be used in conjunction with discrete power triacs.

Thinklogical
Milford, CT 06460
May 13, 2008 Designed for broadcast and post-production, ImageEvolution video processor is suited for image correction and scaling while also functioning as video converter that supports HDMI, SDI, and HD-SDI. It has Gennum VXP(TM) image processor and offers multi-mode fiber ports for video extension up to 3,280 ft. Also available, ImageEvolution HDMI Repeater for distribution of one of 2 HDMI/DVI video sources to 4 digital displays, simultaneously, with identical reproduction and no signal loss.

HOLOEYE Corp.
Laguna Hills, CA 92653-1340
May 12, 2008 Based on reflective LCOS microdisplays with 1,920 x 1,080 pixel HDTV resolution, PLUTO phase only spatial light modulators feature pixel pitch of 8.0 µm, image refresh rate of 60 Hz, and pure phase shift of 2 Pi up to 1,550 nm. PLUTO-VIS, PLUTO-NIR, and PLUTO-TELCO are optimized for 420-850, 850-1,100, and 1,550 nm wavelengths, respectively. They are suitable for applications such as wave front correction, optical tweezers/metrology, interferometry, lithography, or holography.

Agilent Technologies, Inc.
Palo Alto, CA 94303
May 12, 2008 Facilitating design and validation testing, 86116C Option 025 provides reference receiver capabilities for 100-G Ethernet and 16X Fibre Channel signals. Module works with 1,310 nm and 1,550 nm single-mode transmitters, and characteristically has 45 GHz optical and 93 GHz electrical unfiltered bandwidth. Used in 86100C DCA-J oscilloscope mainframe, unit helps engineers investigate, design, and verify performance of transceivers that terminate optical fibers for LANs and SANs.

Toshiba America Electronic Components (TAEC)
Irvine, CA 92618-1811
May 02, 2008 Supplied in 4-pin, 6.5 x 4.6 x 3.5 mm plastic DIP, general-purpose TLP781 consists of silicone photo-transistor optically coupled to gallium-arsenide IR emitting diode. Solution meets reinforced insulation class UL, BSI, SEMKO, and VDE international safety standard requirements; offers isolation voltage up to 5,000 V(rms); and has 7.62 mm lead pitch. Variation with wide lead spacing (10.16 mm pitch), TLP781F, is also available.

Weidmuller, Inc.
Richmond, VA 23236
May 01, 2008 Industrial Ethernet connectors provide IP67 solutions for copper and fiber optic cabling across all Ethernet standards. Connector plug and bulkhead housings in die cast zinc, polyamide plastic, and die-cast aluminum, are available in Ethernet/IP, Ethernet TCP/IP, and PROFINET® versions. Each version is completely sealed to withstand extreme environmental conditions. STEADYTEC® cable pass-through design accepts shielded cables up to AWG 22 and allows 8-wire cables to be used.

ARRIS
Suwanee,, GA 30024
Apr 16, 2008 With 1 GHz CHP CORWave, MSOs can leverage existing fiber networks for delivery of HD-On-Demand, SDV, and business services. When deployed with ARRIS OptiMax4100 4 x 4 segmentable nodes, CORWave enables multiplexing of 12 wavelengths: 4 forward, 4 return and 4 bidirectional, all on one fiber with link length of up to 25 km. When deployed with ARRIS OptiMax segmentable nodes in 2 x 2 configuration, CORWave enables longer link lengths of up to 30 km.