Coherent Inc., Laser Group
Santa Clara, CA 95054-1112
May 29, 2007 Featuring consumable crystal lifetime of 40,000 hr, RoHS-compliant AVIA 266-3 offers users deep UV diode-pumped solid state (DPSS) laser that provides 3+ W of Q-switched output at 266 nm and pulse repetition rates to 100 kHz. Use of automated systems such as Posilock(TM) beam pointing active stabilization system delivers optimal spatial control and resolution. Offering pulse to pulse stability, laser is suited for use with range of materials.

Renishaw, Inc.
Hoffman Estates, IL 60192
May 24, 2007 Bringing nanometer-level motion analysis to calibration, error-mapping, and compensation processes, lean design XL-80 system makes all measurements based on wavelength of stabilized HeNe laser source. Portable product weighs 3 kg, takes readings at 50 kHZ, and offers environmentally corrected accuracy to ±0.5 ppm over 32 to 104°F operating range. Other characteristics include 4 m/sec linear measurement speed, 1 nm resolution, and warm up time of less than 6 min.

Pinpoint Laser Systems
Peabody, MA 01960
May 09, 2007 Designed for use on factory floor to align and adjust various machinery, Spindle Alignment Kit provides information on runout, centerline offset, parallelism, concentricity, and other parameters to achieve optimal alignment. With ability to measure to precision of 0.0001 in., Microgage system features round laser that is secured into chuck or attached to end of shaft/spindle and allows for alignments up to 150 ft distances.

J P Sercel Associates
Manchester, NH 03102
May 01, 2007 Designed for isolation and series interconnection of thin film solar cells, PV Series laser scribing system produces fine scribed lines with greater than 30 mW isolation. It can remove wide range of thin films from large glass, metal, or polymer substrates. Variety of wavelengths for different layer materials are available including 1,064, 532, 355, and 266 nm. Modular workstation can accommodate 1,300 x 1,300 mm glass sheet sizes.

Pinpoint Laser Systems
Peabody, MA 01960
Apr 13, 2007 Suited for use in factories and manufacturing facilities, Dual-Axis Alignment Kit includes 90-Line laser squaring attachment for checking machine beds, vertical cutting machinery, roll parallelism, squaring slides and gantries, and measuring geometric parameters. Laser beam enters 90-Line through port in front and exits out side port at 90° to incoming beam. Machined from solid aluminum, 90-Line has locking mechanism for pre-set positions and friction lock to hold beam in place.

JDSU
San Jose, CA 95131
Apr 04, 2007 Erbium-doped Fiber Amplifier (EDFA) 980 nm pump lasers include 3000 Series and 2945 Series, which respectively produce 660 and 400 mW of optical power. Latter can operate at internal temperature of 45°C due to laser chip technology that does not require refrigeration down to 25°C to ensure reliable operation. Designed for agile optical networks (AONs), both series perform at reliability figure below 5 FIT.

Laser Design, Inc. (LDI)
Minneapolis`, MN 55431
Mar 29, 2007 With laser line length of 25 mm, Model SLP-250 provides scanning accuracy of ±6 µ and is primarily used for small or highly detailed objects. Model SLP-2000, featuring laser line length of 200 mm, delivers accuracy of ±80 µ. Both probes have dual CMOS receptors that capture up to 75,000 points/sec, making them suited for high-speed, non-contact 3D scanning. Units integrate with 7-axis arms from Faro and Renishaw PH10 indexing system used on most CMMs.

Laser Photonics, Inc.
Lake Mary, FL 32746
Mar 20, 2007 Custom-tailored to application needs, Fantom(TM) Series OEM CO2 Laser Marking and Engraving Kits include choice of 10, 30, and 100 W models. Each system is based on folded Wave Guide laser resonators, DSP controllers, as well as direct imaging and scanning technologies. While shielding gas to scanner prevents external dust particles from contaminating lens and mirrors, graphics-based marking and engraving software and text-based architecture facilitate operation.

Universal Laser Systems, Inc.
Scottsdale, AZ 85260
Mar 15, 2007 PLS line of CO₂ laser cutting, marking, and engraving systems feature materials-based print driver that gives users choice between automatic or manual control over power, speed, and other system settings. All 4 models feature industrial design with built-in storage space and keypad/display interface. Units are also available with optional HPDFO(TM) optics which allows for direct marking onto uncoated metals such as steel, chrome, iron, and titanium.

Universal Laser Systems, Inc.
Scottsdale, AZ 85260
Mar 14, 2007 VersaLaser(TM) computer-controlled CO₂ laser cutting, marking, and engraving system runs like a desktop printer from Windows® based graphic software and can transform images or drawings on computer screen into real items made out of variety of materials. Unit is available with optional HPDFO(TM) optics which allows for direct marking onto uncoated metals such as steel, chrome, iron, and titanium.

New Wave Research
Fremont, CA 94539
Mar 06, 2007 As flexible analytical tool for range of materials, UP193-FX 193 nm short-pulse excimer laser ablation system is suited for bulk or micro-feature analysis and includes 13 pre-calibrated spot sizes with constant fluence. Use results in consistently smaller aerosol particles from all materials for optimal ionization and crater quality as well as minimal fractionation. System offers fully homogenized beam, wavelength coupling to ICP-MS, and up to 4 GW/cm² irradiance at sample.

NP Photonics, Inc.
Tucson, AZ 85747
Feb 26, 2007 Based on passive stabilization technique that reduces frequency noise sensitivity to low frequency acoustics, Rock fiber laser is designed for DWDM fiber-optic sensing systems that multiplex information from spectral channels. Laser is suitable for use in multi-laser systems that are used for trials in oil field and security markets.

Pinpoint Laser Systems
Peabody, MA 01960
Feb 14, 2007 Combining laser transmitter with receiver and digital display, Microgage 2D operates on batteries over distance of 100 ft. All components are machined from solid aluminum with hard anodized coating for wear resistance. Serial and USB interface connect to PC and link to spreadsheets for plotting and analyzing data. System is suitable for checking and aligning roll and web lines, CNC cutting and milling equipment, lathes, stamping presses, and injection molding machines.

Photonic Products, Ltd.
Huntington Beach, CA 92647
Feb 14, 2007 Suited for industrial alignment and machine vision applications, 300-0100-00 Series 645 nm Modules offer interchangeable pre-aligned optics, including 88° cross, 58° line, and 58° cross/spot. Units incorporate anti-surge, anti-static, and reverse protected electronics, as well as anti-reflection, scratch-resistant glass window, and 2.1 mm jack socket, all contained in 14 mm dia housing. Each is supplied with adjustable mounting bracket, power supply, and power adjustment tool.

Cynosure Inc.
Chelmsford, MA 01824
Feb 06, 2007 Incorporating 3 energy sources, Affirm(TM) Workstation uses 1,320 nm Nn:YAG laser for tissue tightening through deep-heating, 1,440 nm Nd:YAG laser for fractional micro-rejuvenation, and Xenon Pulsed Light system for discoloration. Combined Apex Pulse(TM) technology redistributes laser energy in combination of high and low level heat to stimulate and remodel collagen production, while Multiplex technology enables rapid sequential emission of 2 wavelengths from same optical fiber.

JDSU
San Jose, CA 95131
Feb 05, 2007 With fiber based architecture, Model FCD488 continuous wave 10 and 20 mW 488 nm laser is available in free space and fiber delivered output configurations. Telecom-based, visible solid state laser features low heat dissipation, and utilizes components such as diode lasers with over 100,000 hr lifetime.

Leica Geosystems Inc.
Norcross, GA 30092
Jan 26, 2007 Rugby 55 features easy-to-use keypad, watertight seal, variable head speeds, selectable scanning modes, bright red beam, and alkaline or rechargeable NiMH battery pack. Scan-90 feature moves scanning or stationary beam in 90° intervals through each of 4 axes, while beam down mode positions beam below laser when doing layout work. Sleep Mode helps conserve battery life. Mounted on tripod or batter board clamp, Rugby 55 allows user to set out corners and align forms and foundations.

Bookham, Inc.
San Jose, CA 95134
Jan 25, 2007 LambdaFlex(TM) Model TL5000VLJ offers L-band capability with in-service power adjustment, while Model TL5000VCJ brings in-service power adjustment to existing C-band iTLA. Laser and control electronics are pre-mounted on dedicated circuit board to facilitate integration into customer's systems. Units provide narrow line width, internal frequency dither generation, direct input path for TX trace tone functionality, dark tuning, and field programmable firmware.

Pinpoint Laser Systems
Peabody, MA 01960
Jan 17, 2007 Able to operate over distances from few inches to 120 ft, Laser-based Microgage 2D system measures flatness of rolls, moving machinery stages, gantry systems, actuators, and moving equipment to precision of 0.0001 in. It may also be used for leveling and checking machinery that may be exhibiting high-wear characteristics. Battery-operated, 2-axis product combines compact laser transmitter with receiver and digital display. Accessories expand alignment capabilities.

Pinpoint Laser Systems
Peabody, MA 01960
Jan 12, 2007 Microgage 2D Factory Alignment Kit features 90-Line Right Angle which takes reference laser beam from Microgage 2D and turns it by 90° for squaring machinery and equipment. Capable of holding precision optical elements that redirect laser beam, Angle housing has several adjustments that allow square exiting beam to rotate through a full plane. Beam can be adjusted with precision rotary mount, and 2-axis stage mount allows easy positioning of the 90-Line.