Ophir Optronics, Inc.    Wilmington, MA 01887
Feb 13, 2013 With 320 x 320 pixel pyroelectric array that can profile beams up to 25 mm without reduction optics, Pyrocam IV measures pulsed and CW (continuous wave) lasers from 13–355 nm and 1.06 to greater than 3,000 µm. Electronics control design includes interface to GigE (Gigabit Ethernet) cameras, and integral focal plane chopper is included for CW beams and thermal imaging. Other features include 14-bit ADC, SNR of 1,000:1, and Ultracal® baseline algorithm.

Ophir Optronics, Inc.    Wilmington, MA 01887
Feb 11, 2013 Using moving slits, NIST-calibrated NanoScan 2 measures continuous wave (CW) and pulsed beams across spectral range from UV to far IR. Beam size and beam pointing can be measured with 3 sigma precision of several hundred nanometers. While USB2 interface provides deep, 12-bit digitization of signal for dynamic range up to 35 dB power, digital controller improves accuracy and stability of measurements. Software can measure 1–16 beams in NanoScan aperture, all with sub-micron precision.

Ophir Optronics, Inc.    Wilmington, MA 01887
Feb 07, 2013 Along with 4008 x 2672 pixel format that allows profiling of beams up to 24 x 36 mm without requiring reduction optics, L11059 USB Large Format Beam Profiling Camera features 50 mm ND filters that provide max power density measurements to 15 mW/cm² without additional attenuation. Frame rates of up to 3.1 fps are supported at full resolution (up to 17 Hz in 4x4 binning mode). Featuring 59 dB dynamic range, camera can measure CW laser beams over spectral range from 190–1,100 nm.

Ophir-Spiricon Inc.    Logan, UT 84321
Jan 24, 2013 Working with CW and pulsed lasers down to single shot rates, Photon M2-1780 automatically measures M2 beam propagation ratio and all associated ISO 11146 parameters instantaneously at video rates over 20 Hz. CCD camera-based system, sensitive to wavelengths from ~250–1,100 nm, automatically measures with NIST-traceable accuracy to better than 2%. This translates to M2 measurements with accuracy to -5%. System works in conjunction with FireWire BeamPro Acquisition and Analysis software.

Ophir Optronics, Inc.    Wilmington, MA 01887
Mar 24, 2011 Combining NanoScan near-field profiler with dedicated M² measurement hardware and software, NanoModeScan enables quantitative measurement and viewing of high-power CO2 laser beams in as little as 20 sec. System also reports beam waist diameter and location, divergence, and beam's Rayleigh range for each axis. With update rate of 20 Hz, system is suitable for CO2 laser-based material processing, machining, and marking applications where laser performance needs to be adjusted in real time.

Vernon Tool Co.    Oceanside, CA 92054
Sep 28, 2010 Suited for small- to medium-sized fabricators of tube frame assemblies, MasterPipe(TM) Profiler (MPP) 2-axis, CNC pipe cutting machine is powered by Windows®-based OS and operated via touchscreen. It consolidates setup, programming, and cutting into one operation, and pre-loaded cut library optimizes pipe configuration flexibility. Capable of performing range of standard cuts, machine handles 1-12 in. OD pipe in lengths up to 40 ft.

Photon, Inc.    San Jose, CA 95119
Sep 25, 2009 Operating under BeamProfiler Software in MS Windows®, USBeamPro CCD provides NIST-traceable measurements of ISO Standard laser beam profile parameters - laser beam diameter, centroid, power/energy - for CW, pulsed, and single-shot lasers. USB 2.0 interface facilitates use and promotes portability, while ½ in. format 1,360 x 1,024 array with 4.65 µm square pixels offers total imaging area of 6.32 x 4.76 mm. Camera dimensions (70 x 95 x 33 mm) aid placement into typical optical paths.

Ophir-Spiricon Inc.    Logan, UT 84321
Apr 21, 2009 Designed to verify performance and reduce changeover time for industrial parts manufacturers, ModeCheck(TM) enables quantitative measurement and viewing of high-power CW and pulsed lasers in 8-30 µm range with intensities up to 30 W/cm². Industrial solution measures key characteristics of laser beam profile in real-time and stores mode images for later recall and comparison. Over time, user will be able to measure laser degradation and predict and schedule downtime for maintenance.

Coherent Inc., Laser Group    Santa Clara, CA 95054-1112
Dec 12, 2008 Operating over 190-355 nm spectral range, LaserCam-HR-UV records beam characteristics at third (355 nm), fourth (266 nm), and fifth (213 nm) harmonics of Nd:YAG lasers, as well as output of most excimer lasers. LaserCam-HR-InGaAs measures infrared laser beams from 900-1,700 nm, and is compatible with eye safe military lasers, telecom sources, and Nd:YAG fundamental. Both units are powered through single BeamView(TM)-USB 2.0 cable connection.

Ophir-Spiricon Inc.    Logan, UT 84321
Jul 28, 2008 Supplied with LBA beam analysis software, USB L11058 Large Format Beam Profiling Camera has 4,008 x 2,672 pixel format that allows profiling of UV laser beams up to 24 x 36 mm without requiring reduction optics. It measures CW laser beams over 190-1,100 nm spectral range and has wide dynamic range of 59 dB. While global shutter allows simultaneous integration of entire pixel array, integrated USB 2.0 digital interface allows data transfer to laptop/desktop PCs.

Ophir-Spiricon Inc.    Logan, UT 84321
Jul 27, 2007 Model M2-200S Beam Propagation Analyzer features UV operation between 250-370 nm, visible operation from 400-700 nm, and NIR operations from 650-1,100 nm (1,064 nm YAG) and 1,000-1,800 nm (1,064 nm YAG plus telecom). All measurements and translations as well as incremental beam attenuation are automatically controlled by M2-200S software. ISO compliant unit comes in M2x, M2y, Ky, Ky, BPPy, BPPy, width at waist Wy, Wy, and waist location at Zy, Zy.

Ophir Optronics, Inc.    Danvers, MA 01923
Aug 25, 2005 BeamStar FX Beam Profiler Systems include camera, filters, plug-and-play PC card, and version 1.10 software. Users can align Major/Minor axes instead of X and Y for beam shapes not aligned to X and Y. With Point-to-Point Distance Measurement, users can right click mouse and move, then right click again to measure distance between any 2 points. Additional features include M² measurement capabilities, 2D Gaussian Fit, and Region of Interest capabilities.

Ophir Optronics, Inc.    Danvers, MA 01923
Jan 18, 2005 BeamStar FX Beam Profiler CCD Camera is available with variable attenuator option that provides control over 4 orders of magnitude from 350–1,100 nm wavelengths. Attenuation is variable from microwatts to watts. Beam splitters include UV grade fused silica wedge beam splitter that fits onto camera and another splitter that stands alone on adjustable stand. Latter allows camera operation up to 2 W, while former allows operation up to 40 W.

Spiricon, Inc.    Logan, UT 84341 5740
Dec 09, 2004 LBA-FW profilers utilize 12- or 14-bit digital FireWire cameras that connect directly to laptop computers without frame grabber card, providing portable beam analysis instrument. Megapixel CCD and pyroelectric cameras are provided to cover spectral range from UV to far IR. Multiple FireWire cameras can operate on one FireWire bus, enabling multiple, simultaneous laser beam profilers. Cameras capture CW and pulsed lasers beams.

Ophir Optronics, Inc.    Danvers, MA 01923
May 06, 2004 Digital BeamStar FX Series works with laptop or desktop PCs to provide everything necessary for beam profiles of pulsed and CW lasers from µW to W. System consists of camera, filters, laptop or PC card, and software. Trigger input lets BeamStar FX 33 and FX 50 synchronize with trigger output from pulsed laser. Series features automatic gain and exposure adjustment as well as automatic photodiode synchronization with pulsed lasers.

Ophir Optronics, Inc.    Danvers, MA 01923
Jul 10, 2003 Designed to measure beam profile and power of pulsed industrial Nd:YAG and Diode industrial lasers, BA100 displays laser beam intensity profile in real time. Instrument makes measurements at full or near full power levels (1,000 W max) and is useful for looking at focal spots. Beam profile can be shown in 3D form and rotated to different angles and elevations. Unit handles pulse energies to 30 Joules and has beam area of 25.6 x 19.2 mm with 5.7° field of view.

Ophir Optronics, Inc.    Danvers, MA 01923
Jun 09, 2003 Self-contained BeamStar FX 66 provides measures CW and Pulsed lasers using laptop or desktop personal computer. Connected to PC via one Firewire interface card, product offers software with manual or automatic gain and shutter control adjustments. Laser beam focal point, vertical and horizontal spectral profiles, and beam statistics are displayed on screen. It has aperture of 9.7 x 7.68 nm, 1280 x 1024 pixels, and provides dynamic measurement range of 53 dB.

Melles Griot    Irvine, CA 92606
Dec 17, 2001 WinCamD 3-dimensional beam intensity profiler features 4.65 µm square pixel size and 14-bit analog-to-digital converter that gives it greater than 16,000 levels of intensity resolution. WinCamD includes pass/fail settings for beam width, relative power, Gaussian and top hat fit, and data logging. It can be used for pulsed (as low as 1 Hz) or continuous-wave beams. Use of variable electronic shutter provides dynamic range of 60,000:1.