Optotherm, Inc.    Sewickley, PA 15143
Jul 30, 2007 Equipped with 16 bit digital camera link interface and microscopic lens with 20 µm spatial resolution, Micro thermal imaging system detects shorts/defects on semiconductor devices and small circuit boards. It can also measure junction temperature, identify die bonding defects, and measure packaged die thermal resistance. Thermal stage provides both heating/cooling for precise device temperature control to locate short circuits and compensate for pixel emissivity variations.

Newport Corp.    Irvine, CA 92606
Jul 27, 2007 Pantera(TM) diode-pumped solid-state laser provides 12 W of stabilized UV power at wavelength of 355 nm. It uses fiber amplifier platform that is powered by fiber coupled, hermetically sealed diodes and is not affected by external influences such as mechanically-induced misalignment. High power picosecond laser is suited for wide range of OEM applications, particularly in solar cell, flat panel display, printed circuit board, and semiconductor manufacturing.

Ophir-Spiricon Inc.    Logan, UT 84321
Jul 27, 2007 Model M2-200S Beam Propagation Analyzer features UV operation between 250-370 nm, visible operation from 400-700 nm, and NIR operations from 650-1,100 nm (1,064 nm YAG) and 1,000-1,800 nm (1,064 nm YAG plus telecom). All measurements and translations as well as incremental beam attenuation are automatically controlled by M2-200S software. ISO compliant unit comes in M2x, M2y, Ky, Ky, BPPy, BPPy, width at waist Wy, Wy, and waist location at Zy, Zy.

Tektronix, Inc.    Beaverton, OR 97077
Jul 26, 2007 TDSHT3 compliance test software supports HDMI compliance test specification version 1.3b. Test suite controls signal generators in closed loop mechanisms for automatic performance of cable and sink tests. It includes DPO70804 real-time oscilloscope, 3.3.1 version of TDSHT3 HDMI compliance test software, DSA8200 sampling oscilloscope, DTG5334 data timing generator with DTGM30 modules, and P7313SMA differential SMA probes.

OmniGuide, Inc.    Cambridge, MA 02139
Jul 26, 2007 Suited for otology procedures, OtoBeam enables CO2 laser-based energy source to be placed at surgeon's fingertips for accurate control when operating on delicate structures of middle and inner ear. Photonic bandgap fiber technology allows laser energy to be guided through flexible fiber, providing surgeons with precise and safe device for stapedectomy procedures. Flexible CO2 laser fiber also promotes control over penetration into target structures and formation of footplate rosette.

Visual Defence Inc.    Richmond Hill   Canada
Jul 26, 2007 Integrating Virtual Matrix System software module, IP Mobile Digital Video Storage Solution provides central station operators with video management capabilities including ability to remotely protect and tag specific video for downloading. Video recorded on vehicles can be downloaded by removing hard drive, by direct Ethernet connection, or remotely over IP networks. Watertight and dustproof, recorder includes 8 network ports, IP-61 compliancy, and 6 PoE connections.

Micrel Semiconductor Inc.    San Jose, CA 95131
Jul 24, 2007 Single-chip programmable SERDES, Model SY87725L, supports multiple Passive Optical Network standards and rates including asymmetric Gigabit Passive Optical Network with data rates up to 2.5 Gbps on receive side and 1.25 Gbps on transmit side. It offers complete clock recovery and data retiming circuitry, along with integrated 4-bit serial-to-parallel data converter on receive side. On transmit side, device includes synthesizer with integrated 4-bit parallel-to-serial data converter.

Alcatel-Lucent    Paris 75008  France
Jul 24, 2007 Allowing carriers to deliver triple play services, 7342 ISAM fiber-to-the-user solution Rel 4.4 features multiple dwelling unit optical network terminal that provides voice, video, and data over building's copper wires. Line card has four GPON ports, each of which can support up to 64 subscribers with 2.5 Gbps downstream and 1.25 Gbps upstream line rates. Optical network also supports VoIP with SIP and H248 and IPTV with IGMPv3 for TV channel change.

CeramOptec    Longmeadow, MA 01702
Jul 18, 2007 Optimized for heat transfer, High Power SMA-Based Fiber Connectors utilize design based on copper alloy with heat conductivity of 320 W/mK to allow laser power to be transmitted through SMA cable. Fiber core diameters of 100, 200, 400, and 600 µm are readily available, and others upon request. Typical observation consists of coupling HeNe laser with NA of ~0.05 into large core fiber (over 100 µm) with standard NA of 0.22 and obtaining output beam divergence corresponding to NA~0.07.

Audio Video Supply, Inc.    San Diego, CA 92111
Jul 17, 2007 Featuring MegaVideo(TM) technology, MEG-IP5 5 megapixel sensitive, ½ in. optical format IP camera delivers full motion HDTV resolution of 2,560 x 1,600 in either day or night. Cinema compatible video frame rate of up to 15 fps allows HD digital video surveillance with ultra forensic zooming after event in available picture-in-picture mode. Unit also has sensitivity up to 1 lux at F1.4 allowing real-time motion detection of up to 64 separate zones for each channel.

Fixturlaser AB    Molndal SE-431 21  Sweden
Jul 17, 2007 Fixturlaser OL2RXA laser based wireless shaft alignment tool enables production personnel to adjust fixtures by use of point lasers. System is upgradeable for measurements of dynamic movements, such as thermal growth and process forces. System capabilities include 3D flash tutorials, measurement of several machines, saved measurements, and sight adjustment which enables fixture mounting without alignment-system use.

Honeywell Sensing and Control    Golden Valley, MN 55422
Jul 17, 2007 Available in 3,000+ product combinations, FF-ST Series lets end users build safety light curtain solutions with variety of resolutions, scanning ranges, and protective heights. Core functionality options include push-pull safety outputs, restart modes, EDM loop options, floating blanking, and muting functions. Available in Type 2 European standards and Type 4 global standards, curtains are designed to be installed without use of software, dip switch, or configuration/micro card.

Coherent Inc., Laser Group    Santa Clara, CA 95054-1112
Jul 17, 2007 Featuring pulse duration of less than 30 ns, AVIA 355-14 supports pulse repetition rates as high as 300 kHz, enabling vector scanning and high-speed raster scanning. Frequency-tripling component has projected lifetime of providing stable output power for more than 60,000 hr. Suited for micromachining applications, solid-state Q-switched laser includes Posilock(TM) beam position sensor and feedback system, total pulse control, and variety of pulse-shaping features.

Lenox Instrument Co.    Trevose, PA 19053 3427
Jul 13, 2007 Combining 3 viewing angles into one, Swing Prism Borescope includes 2X zoom eyepiece for magnified inspection. Seven models are available, each offering 120° viewing arc, diameters ranging from 6-8 mm, and working lengths of 290-910 mm. Control on eyepiece lets user adjust viewing angle of prism located on front of scope without withdrawing borescope from subject undergoing inspection. Units are adaptable to optional digital camera or video systems.

Lenox Instrument Co.    Trevose, PA 19053 3427
Jul 13, 2007 Adaptable to most fiber optic illuminated borescopes, fiberscopes, and videoscopes, cordless Model 3000LS-3.5LED operates on 3 C-cell batteries for 24 hours before new alkaline or rechargeable batteries are needed. Illumination is delivered by 5,000-6,000° Kelvin LED light, which produces up to 110,000 lux at input to light guide. Weighing 1.4 lb with batteries installed in 11 in. handle, light source offers shock and impact resistance.

Columbia Marking Tools, Inc.    Chesterfield, MI 48047
Jul 12, 2007 Utilizing pulsed fiber diode laser technology that develops same 1,064 nm wavelength as Nd:YAG and Nd:YVO4 lasers but in compact design, Columbia 10 and 20 W Systems eliminate need for sensitive optical components. E-Z Mark(TM) software features Windows-based user interface and enables systems to be tailored to customer's requirements with specific application for UID/2D marks. Standard marking functions include alphanumeric, bar codes, data matrix, UID, and graphics.

Laurel Electronics, Inc.    Costa Mesa, CA 92626
Jul 12, 2007 Housed in 35 mm DIN rail case, Laureate Model TA-FRT is powered by 95-240 Vac ±10% or optionally by low voltage 8-28 Vac or 9-37 Vdc. It produces isolated 4-20 mA or 0-10 V output and includes dual-channel signal conditioner, which is suitable for pulse or ac sources, such as NPN or PNP proximity switches, contact closures, magnetic pickups down to 12 mV, or ac voltages up to 250 Vac. Equipped with RS232 port, transmitter is programmed via external PC and Instrument Setup software.

Quantum Devices, Inc.    Barneveld, WI 53507
Jul 12, 2007 Model JR12 provides feedback solution in applications typically using pancake resolvers with same threaded shaft and jam nut mounting. Flexible member enables tail shaft run out and TIR and mounting flange eliminates need for servo mounting clips. Output options consist of quadrature with index pulse and 3-phase commutation.

Energetiq Technology    Woburn, MA 01801
Jul 12, 2007 Saturn(TM) DUV (Deep Ultra Violet) Lamp Subsystem offers an operating wavelength range of 170-400 nm to eliminate electrical/heat damage in thin-film and surface processes. System features include compact housing, debris-free electrodeless toroidal bulb design, integrated power supply, internal water cooling, and re-circulating nitrogen cooling to avoid toxic ozone production. Light source is suitable for photoprocessing and cleaning applications.

Metronor, Inc.    Seattle, WA 98101
Jul 12, 2007 Employing 2 cameras, SOLO TWIN offers point-and-shoot functionality and 70° field of view that lets operator get close to assembly tooling that needs to be measured for certification and alignment. Within 15 minutes, unit makes it possible to set-up measurement system; tie-in to coordinate system; perform measurements of critical assembly tool features; verify measurement data relative CAD nominal; and correct tool alignment issues of tool without interfering with production cycle.