Mounts

Mounting & Attaching Products, Safety & Security Equipment, Optics & Photonics

Roof Mounts feature non-penetrating design.

March 20, 2015

Using 8 x 8 x 16 in. cinderblocks as ballast to avoid damaging roof surface, FRM Series is suited for wireless security surveillance systems, as well as DBS, off-air antenna, satellite internet systems, and point-to-point CCTV signal transmission. FRM-125 features 60 in. mast with 1.25 in. OD, while FRM-166 has 30 in. mast with 1.66 in. OD. In addition, FRM-200 provides 30 in. mast with 2 in. OD. FRM-MAT Protective Rubber Mat is available as accessory for all FRM mounts. Read More

Mounting & Attaching Products

Portrait-Oriented Video Wall Mount carries ADA compliance.

March 19, 2015

Supporting up to 100 lb, portrait-oriented displays from 37–65 in., LMVSP Press & Release™ Pop Out Ultra-Slim Mount in Portrait Orientation incorporates Press & Release feature that provides users with service access in <5 sec. Kickstand, also included, gives 7° of clear access to rear of display. Panels can be aligned with X/Y/Z axis adjustments located on top adjustment brackets, and 1.98 in. space between mount and wall provides ADA compliance. Read More

Mounting & Attaching Products

Articulating Wall Mount holds 27-42 in. flat panel displays.

March 12, 2015

With closed depth of 1.6 in. and fully opened extension of 16.4 in. Model FP-MLPAB supports most 27–42 in. flat panel displays up to 55 lb. Unit offers fully adjustable 10° tilt, 3° list adjustment, and ±45° of rotation. Designed to install into single stud, mount has maximum flat panel hole pattern of 400 x 400 mm. Other features include black powder coat finish, integrated cable management system and level, and mounting rails that accept padlocks for security. Read More

Fluid & Gas Flow Equipment, Mounting & Attaching Products, Computer Hardware & Peripherals, Fasteners & Hardware

Truss Ceiling Adapter offers 180 lb load capacity.

March 5, 2015

Designed to attach ceiling mounts to variety of trussing or pipe, Model TCA-1 is capable of adapting up to max diameter of 3 in. or max cross section dimensions of 3 x 3 in. Adapter has black powder coat finish and includes cable pass throughs for cable management. Measuring 5.5 x 5.5 x 7.6 in., adapter is suited for public view monitors or PTZ cameras in retail, commercial, or industrial settings where truss ceilings are used. Read More

Mounting & Attaching Products, Thermal & Heating Equipment, Test & Measuring Instruments

Programmable Hot Plate allows direct work on heater surface.

February 3, 2015

Featuring 12 x 12 in. milled-flat cast aluminum heater top, EchoTherm™ Model HP61A offers even heating with ambient to 450°C range controlled to ±1°C of target. Programming is done via front panel membrane switch and LCD, and accuracy is 1% of reading. Unit stores 10 programs with up to 10 steps – temperature, temperature ramp rate, time – in memory that can be made to repeat. Features also include RS232 port, adjustable temperature ramping rates, and countdown timer with alarm and Auto-Off. Read More

Mounting & Attaching Products

Gripper Accessory increases available sensing capability.

January 29, 2015

Available for Series 8400 and Series 190/191 grippers, JC1STP Teachable 2 Position Switch Mounting Kit provides switch plate with slots for either one or 2 Series JC1STP Switches to mount to bottom surface of grippers. Use of 2 switches allows sensing of up to 4 jaw positions throughout jaw travel. As it uses existing switch ready option, this accessory offers facilitated application by requiring only mounting plate and switches. This solution is available for all sizes of grippers. Read More

Mounting & Attaching Products

Ceiling Mount Adapter accepts up to 80 in. flat panels.

January 16, 2015

With PDS-LCM2B Adapter, PDS-LCB tilt ceiling mount can accommodate two 37–80 in. flat panel displays back-to-back with combined weight up to 360 lb. Adapter offers 0–15° tilt and supports hole patterns ranging from 200 x 200 mm up to 860 x 500 mm. Designed with black powder coat finish, adapter offers multi-function option for host of applications, including restaurants, bars, health clubs, and arenas. Read More

Mounting & Attaching Products

Tilt, Swivel and Swing Display Mount features locking arm.

January 12, 2015

Featuring integrated positioning technology, A Series offers precise control and customization of operation. Unit is designed with plunger that locks arm securely into place, maintaining position in extreme conditions where motion or vibration may cause display drift. Validated for 20 k cycles of operation, mount enables effortless fingertip positioning and eliminates need for constant maintenance and readjustment. Read More

Mounting & Attaching Products

Elevator Cab Internal Panel Mount simplifies installation efforts.

December 29, 2014

Available as wall panel clipping system/process, EPIC Solution eliminates extraneous efforts and issues associated with cab interior installation jobs. Product reduces time by minimizing number of steps required during installation and also provides flexibility in material selection. Furthermore, solution increases applicational versatility in that wall panels can be oriented vertically or horizontally. Read More

Mounting & Attaching Products

Articulating Wall Mount holds flat panel displays up to 55 lb.

December 17, 2014

Intended for 27–42 in. flat panel displays, Model FP-MLPAB provides closed depth of 1.6 in., fully opened extension of 16.4 in. as well as fully adjustable 10° tilt, 3° list adjustment, and ±45° of rotation. Unit is designed for installation to single stud and has maximum flat panel hole pattern of 400 x 400 mm. In addition to black powder coat finish, mount includes integrated cable management system, level, and mounting rails that accept padlocks for security. Read More

Material Handling & Storage, Mounting & Attaching Products

Anti-Vibration Mounts feature stainless steel components.

November 7, 2014

Available in inch sizes, GN 451.1/GN 451.2/GN 451.3 Cylindrical Type Vibration Isolation Mounts are suitable for elastic mounting of machine units such as motors, compressors, and pumps. Model GN 451.1 has 2 threaded studs, while Model GN 451.2 has 1 tapped hole and 1 threaded stud, and Model GN 451.3 has 2 tapped holes. Isolation mount body is made of 55 durometer vulcanized natural rubber, while cover plate and tapped inserts/threaded studs are stainless steel. Read More

Transportation Industry Products, Mounting & Attaching Products

Self-Leveling Chocks eliminate soft foot.

October 24, 2014

Self-leveling and height-adjustable, SKF Vibracon Chocks enable accurate mounting of rotating machinery to base frames, steel foundations, or plates while eliminating improper contact between machine casing and baseplate used to support it. Mechanical chocks compensate for angular misalignment of up to 4° between mounting foundation and bottom of machine foot. In addition to standard and extended chocking heights from 30–250 mm, units come in low-profile versions from 20–45 mm. Read More

Computer Hardware & Peripherals, Retail & Sales Equipment, Mounting & Attaching Products

Display Mounts enable fingertip positioning.

October 23, 2014

Designed with integrated Positioning Technology for precise control and customization of operation, AV-D32 Series comprises K Series Tilt and Swivel Mount; A Series Tilt, Swivel, and Single Swing Arm; and A Series Tilt, Swivel, and Dual Swing Arm. Each model, available with wall or tabletop mounting, features integrated wire management channels and minimal joints for easy cleaning. Mounting solutions eliminate need for constant readjustment and provide 20 K cycles of operation. Read More

Computer Hardware & Peripherals, Mounting & Attaching Products

Articulating Wall Mount offers tilt and list adjustment.

October 16, 2014

Offering low-profile alternative for mounting flat panel displays from 32–52 in., Model FP-XMLPAB features closed depth of 1.5 in. and fully opened extension of 16.2 in., along with 15° tilt adjustment, 3° list adjustment, and ±45° of rotation. Mounting rails accept padlocks for added safety and security. Supplied in black powder coat finish, mount additionally features integrated cable management system, integrated level, and 600 x 400 mm max flat panel hole pattern. Read More

Material Handling & Storage, Mounting & Attaching Products

Precision 8 in. Vise reduces part setup and changeover times.

October 3, 2014

Available with 3.750 in. jaw opening, SideWinder™ SDW35 provides vertical workholding of parts for second operation machining in same setup. This 8 in. vise, with max clamping force of 4,000 lb, has Anglock® design that decreases jaw deflection, distributes clamping force evenly and precisely across full jaw surface, and reduces jaw lift. Other features include workstop and porosity-free, 80,000 psi ductile iron body. Pull-type feature reduces stationary jaw deflection.
Read More

Mechanical Power Transmission, Mounting & Attaching Products, Services

Brass Components target marine applications.

July 14, 2014

Made of Quarter Hard Brass Strip with tensile strength of 54,000 psi, Lazy Susan Bearings, Mountings, and Custom Stampings will resist corrosion and rust, making them suitable for marine applications, such as boat seats, or for applications involving water and humidity such as swamp coolers and wash-down food processing machinery. Aesthetically pleasing, brass eliminates need for plating, coating, or other finishing services. Read More

Green & Clean, Mounting & Attaching Products

Solar Inverter Mounting Kit facilitates installation.

July 10, 2014

Able to withstand challenging environmental conditions, corrosion-resistant RAYPORT™ - I provides installers with mounting solution for rooftop- and ground-mounted solar arrays. Corrosion-resistant solution, constructed of stainless steel, fits range of string inverters and can mount at 15° or 30° tilt. Rooftop installations do not require penetration, and 13 lb weight facilitates handling on job site. Read More

Mounting & Attaching Products

Stainless Steel Levelers offer rubber pad options.

June 24, 2014

Offering load ratings from 1,800–4,500 lbf, GN 340.5 Stainless Steel Leveling Mounts feature tapped socket of stainless steel with shot-blast finish. Units come with black pad inlay of Nitrile Butadiene rubber or white pad inlay of Santoprene® rubber. Black pad offers resistance to swelling when in contact with oils and fuels, while white pad has resistance to solvents and acids as well as ozone and atmospheric influences. Inch and metric base diameters range from 1.97–4.72 in. and 50–120 mm. Read More

Mounting & Attaching Products

Roof Mount System minimizes solar rack movement.

June 12, 2014

Consisting of watertight structural attachment system, PowerGrip™ Plus secures ballasted solar racks and other equipment to roofs covered with thermoplastic membranes. System offers tensile strength of 2,000 lbf and shear strength of 1,075 lbf. Wide membrane skirt promotes welding in place, while 1 5/8 in. dia x ½ in. tall mount secures brackets or struts. For long-term performance, exposed 1 x 3/8 in. bolt and mounting stand are made of corrosion-resistant stainless steel and aluminum alloy. Read More

Mounting & Attaching Products

Mounting Systems flexibly position air knives and amplifiers.

May 21, 2014

Made of powder coated steel and suited for difficult environments, Nex Flow™ Mounting Systems provide flexible way to utilize air knives and air amplifiers for blow-off and cooling applications. Products allow for flexible and portable use in manufacturing operations and are also adaptable for other uses. One knob controls infinitely variable system placement and secures it in place after air knife/amplifier is properly positioned, and optional magnetic base is also available. Read More