Wilcoxon Research, Inc.
Germantown, MD 20876
Jul 23, 2008 Measuring 1 in. across flats with 0.82 mounting pad, Models SF21 and SF22 accommodate up to medium diameter accelerometers and small diameter side-exit accelerometers. Models SF23 and SF24 are both 1 1/8 in. across flats with 0.94 in. mounting pad that can accommodate large diameter top-exit sensors. All have ¼-28 integral stud on accelerometer side, and are used to prevent voltage spikes from reaching sensor by electrically isolating it from case of machine.

Misumi USA
Schaumburg, IL 60173
Jul 22, 2008 Suited for building of machinery and equipment, Urethane, Rubber, and Sponge Components come in round and metal plate-mounted versions as well as configurable block versions. Urethane and rubber bumpers feature round tips, and come in choice of solid or through-hole designs. With diameters, lengths, and through-hole sizes configurable in 1 mm increments, hundreds of sizes and shapes are available. Urethane blocks mounted on metal plates are offered in flat, V-shaped, and corrugated designs.

Capital Safety
Red Wing, MN 55066-5005
Jun 18, 2008 Designed to meet requirements of AS/NZS 1891:2007 standard, Delta(TM) Resist Harness and EZ Stop® Resist Shock Absorbing Lanyard feature extruded polyurethane coating that protects against grease, oil, paint, dirt, and grime. Webbing deflects debris, cleans up in seconds, and extends service life. Utilizing RFID, i-Safe(TM) intelligent safety system is built into every harness and lanyard to track inspections, control inventory, and manage information.

Miller Fall Protection
Franklin, PA 16323
May 29, 2008 Designed to meet OSHA, ANSI Z359-2007, and CSA Standards, Miller Revolution(TM) Harnesses and Miller® Shock-Absorbing Lanyards feature vinyl coating on webbing to protect against liquids that could compromise performance. Harnesses include rotary PivotLink(TM) connection, tongue buckle leg straps, 2 pull-free lanyard rings, and clip-on web finials. Rated to 310 lb, lanyards feature SofStop® shock absorber pack with woven inner core that expands up to 42 in. to safely reduce fall arrest forces.

Heyco Products
Toms River, NJ 08753
May 29, 2008 Available in sizes to handle .118-.500 in. mounting hole diameters, Rubber Push-In Bumpers can be used on panel thicknesses from .098-.188 in. and come in range of different shapes to suit varying application requirements. Products are constructed of black SBR and fit snugly into mounting holes so that air or water cannot pass through. Operating temperature range is -40 to +221°F, and additional applications include use as feet.

Tapeswitch Corp.
Farmingdale, NY 11735
May 14, 2008 Suited for use on AGVs, mobile platforms, traveling conveyors, and other moving equipment or machinery, VBL-250 Safety Bumpers activate from average of 4 lb with full collapse achieved as low as 34 N. Capable of up to 8 in. of collapse or crush distance, units are 2.5 in. wide and available lenghts from 4 in. to 16 ft. Polyurethane jacketed switch compartment protects switch from dirt and moisture. Winged version VBL-250-W provides full wrap around corner protection for vehicle.

Rogers Corporation
Rogers, CT 06263 0188
May 12, 2008 Based on open-cell urethane foam technology, E/bak(TM) cushion mounting materials are used to build thickness on cylinder as well as provide cushioning and absorb vibration in corrugated printing process. Allowing for printing on rough surfaces, they maintain high solid ink density for consistent print results over entire press run. Dark green foam with skin surface is available in 0.040, 0.060, and 0.080 in. thicknesses and is 60 in. wide.

Richco, Inc.
Morton Grove, IL 60680
May 09, 2008 Molded in UL94 V2 Nylon 6/6, RoHS-compliant TFR Series snaps in place to facilitate assembly. Once self-threading screw is installed, grommet expands and securely locks screw and assembled parts in place. Grommet legs are forced outward to help seal mounting hole and protect against dust and moisture. Mounting hole is square to prevent rotation.

Boston Retail Products
Medford, MA 02155
Apr 29, 2008 Available in standard and custom colors, ecoFlex® TFC1000 has 1 in. rectangular shape, while TFC1750 has 1.75 in. half-round shape. Bumper systems are manufactured from recycled flexible vinyl and are 100% recyclable. Performance matches original Boston Bumpers®, but inner core contains recycled materials, helping to minimize environmental waste. The ecoFlex® are also available in 2 and 3 in. silhouettes in variety of standard and interchangable profiles, bases, ends, and corners.

Capital Safety
Red Wing, MN 55066-5005
Apr 07, 2008 EZ Stop® II is available as single- or twin-leg tie-back model with standard snap hook, aluminum rebar hook, flat steel rebar hook, or carabiner ends. Its ANSI Z359.1-2007 rebar hooks feature 3,600-pound gates, allowing them to be used in tie-back applications with floating D-ring. Controlled tearing action, when subjected to fall arrest forces, limits arresting forces to no more than 900 lb. Abrasion-resistant tubular webbing covers additional layer of polyester web for durability.

Parker Hannifin Corp., Hydraulic Accumulator Div.
Rockford, IL 61115
Mar 31, 2008 With tunable piston, hydraulic Spring/Shock Absorber, manufacturers can incorporate fully active suspension into heavy-duty mobile equipment. Unit integrates cylinder and accumulator technologies into piston design utilizing leak-free, 5,000-psi nitrogen chamber. Electronic sensors on suspension, in combination with Auxiliary Power Unit, measure impact of ground terrain. Algorithms in control unit signal valves to open and release precise amount of fluid required to combat ground force.

Heyco Products
Toms River, NJ 08753
Mar 20, 2008 Available in 160 sizes to accommodate holes ranging from .250-2.50 in., Rubber Grommets eliminate sharp edges and are designed for mounting or through hole wire applications. They can be used on panel thicknesses from .063-.375 in. and are constructed of SBR with operating temperature range of -40 to 221°F. Suitable for most moderate chemicals, units have water resistance characteristics and can be used with wet or dry organic acids.

Hendrickson
Itasca, IL 60143-1285
Jan 29, 2008 Designed for Mack CH, CHN, and CHU trucks, Hendrickson Aero Bright® 3-Piece Bumper combines steel chromed center sections with HAB end caps for durability. Matching luster of chrome center section, lightweight end caps use thermoplastic polyolefin plastic and weatherable paint films with thick-sheet thermoforming technology.

Pepperl + Fuchs, Inc.
Twinsburg, OH 44087 2245
Jan 21, 2008 Designed for any M18 cylindrical or snout photoelectric sensor, Model OMH-ML17-R mounts on 0.5 in. diameter rod without having to slide half-clamp from end of rod, making it suited for use on conveyor and packaging equipment. Sensor can be positioned 360° around rod as well as along length of rod, and over 100° arc on sensor bracket.

RNR Plastics, Inc.
Raynham, MA 02767
Dec 14, 2007 METALgrommets Kit comes with ¼ and 3/8 in. ID stainless steel die sets and 500 pieces of self-piercing metal grommets and washers and includes 200 brass, 100 nickel, 100 black oxide, and 100 white. It includes ClipShop(TM) Grommet Hand Press that eliminates need for hammers and tools, and features contoured handle, cushioned hand grip for comfort, and large throat depth for flexible grommet placement.

Pepperl+Fuchs
Twinsburg, OH 44087
Nov 26, 2007 Combining intrinsically safe energy limitation and galvanic isolation, FieldConnex® Ethernet Isolators enable high-speed data devices located in hazardous locations to be connected directly to standard Ethernet line. Products also allow for back-to-back, pass through applications without requiring any separate hardware. PCB-mounted version allows OEM to seamlessly integrate intrinsically safe Ethernet into their own equipment.

Optek Technology, Inc.
Carrollton, TX 75006-6905
Nov 07, 2007 Using plastic optical fiber, OPI1270 Series provides power electronics engineers with means to isolate high voltage I/O circuits over distances from 0.71-3.15 in. These RoHS-compliant axial fiber optic isolators are constructed using visible red (645 nm) LED emitter and phototransistor detector in separate opaque molded plastic modules, linked by shrouded and flexible optical cable that shields optical signal from dust and other contaminations.

Heyco Products
Toms River, NJ 08753
Oct 31, 2007 Available in various cable and mounting hole sizes from .079 to over 1 in. dia, Snap-In Cordgrips deliver cord and cable strain relief in limited-clearance applications inside electrical cabinets and product housings. Fingers on end of cordgrip securely lock into cabinet or product housing without tools, and polyamide 6/6 nylon construction is resistant to chemicals. Areas of use include any applications that utilize flexible power cord in non-liquidtight environment.

Richco, Inc.
Morton Grove, IL 60680
Oct 19, 2007 Molded in Nylon 6/6, Series SRSG snaps into place, and when self-threading screw is installed, grommets expand and securely lock screw and assembled parts in place. Grommets also insulate areas of assembly from electrical and thermal transfer and spread load over wide area. Units are RoHS compliant and come in natural color.

RNR Plastics, Inc.
Raynham, MA 02767
Sep 06, 2007 Compatible with common grommet presses, Grommets eliminate need for separate hole punching. Available in brass, antique brass, nickel, and black oxide, they are offered in 1/8 to 1½ in. ID sizes and feature heavy gauge construction and sharp edge. Grommets are suited for various applications including manufacturing awnings, banners, signs, tarpaulins, tents, boat covers, belts, clothing, accessories, draperies, and furniture.