Quicksilver Controls
San Dimas, CA 91773
Jun 23, 2008 Designed to run on SilverNugget N3 servo motor controller/driver, Model QCI-A34M-1 features 400 oz-in. continuous torque, 450 oz-in. peak torque, 200 W continuous mechanical power, 100:1 inertial mismatch, 4,000 rpm, and 12-48 Vdc. Used for direct driving large flywheel loads, NEMA 34 IP50 rated motor suits applications such as winding, spooling, indexing, and tension control, in labeling, packaging, medical, automotive, and entertainment industries.

WEG Electric Motors Corp.
Suwanee, GA 30024
Jun 20, 2008 With outputs from 20-200 hp, WMagnet Motor/Drive Packages offer efficiencies of 95-97%. Motors use rare earth permanent magnets in rotor to limit temperature rise during operation. Utilizing vector control technology algorithm, CFW-09 drive enables control without use of encoder/position sensor. As synchronous motor, WMagnet cannot be started directly from power supply because accurate synchronization of supply waveforms with rotor position is continuously required.

Maxon Precision Motors
Fall River, MA 02720
Jun 20, 2008 Constructed with ironless rotor and 4-pole structure of Neodymium permanent magnets, mechanically commutated RE65 works detent-free and has minimal rotor inertia. Preloaded ball bearings support low-vibration and low-noise operation, and nominal voltage is in 18-70 V range. Depending on winding variation, 65 mm dia x 130 mm long cylindrical drive delivers nominal torque of 0.5-0.9 Nm at nominal speed of 2,400-3,700 rpm.

B & R Industrial Automation Corp.
Roswell, GA 30076
Jun 18, 2008 Designed for X20 controller and I/O system, X20 stepper motor controller features 4 inputs for end switches/encoders, and automatic motor detection when booting and stall detection that identifies overload situations or any unwanted blocking of motor. Stepper motor connections can resolve each full step into up to 256 microsteps. Offering integration with Automation Studio and Soft CNC, unit is designed for bipolar 2-phase stepper motors, 1 A (24 V) or for 3 A (18-48 V) rated current.

Nanomotion
Ronkonkoma, NY 11779
Jun 13, 2008 Designed to meet needs of applications with demanding move and settle profiles with high duty cycle, DuraMotor series withstands ambient operating temperatures from 0 to +50°, vacuum to 10^-7 torr, and Ultra High Vacuum (UHV) to 10^-10. Durability is optimized by chosen materials for motor tip and drive strip, while minimal particle generation promotes level of cleanliness and motor life. Velocities are available from 1 µm/sec to 250 mm/sec.

BEI Kimco Magnetics Div.
San Marcos, CA 92069
Jun 10, 2008 Featuring large diameter clear aperture with high-resolution encoder that supports up to 0.02 arc-sec, Integrated Motor Encoder Assembly is suited for specialty machine applications where high acceleration point-to-point motion is required. Assembly incorporates ABEC7 class precision ball bearings, hollow shaft configuration, and hall-based commutation scheme for seamless connectivity with standard motion controllers.

Bosch Rexroth Corp., Industrial Hydraulics Div.
Bethlehem, PA 18017
May 27, 2008 Suited for assembly of compact power packs, B Series pumps feature 7 cc per revolution, while G Series pumps have displacement of up to 63 cc per revolution for applications in upper power classes. U and T Series pumps offer low noise emissions and vibrations, and satisfy demands for all displacements between 4 and 63 cc per revolution. Individual/combined multiple external gear pumps are suited for machines with operating pressure of 4,000 psi and cover speed range up to 6,000 rpm.

AMETEK Technical & Industrial Products
Kent, OH 44240
May 23, 2008 Available in 5 series (Size 05, 08, 11, 14, and 18), Pittman® micromotors incorporate Parallex coil-winding geometry in slotless motor design to optimize power delivery while minimizing power consumption. They are offered in sizes from .500-1.750 in. and employ NdFeB rare earth magnets, precision ABEC bearings, and balanced rotors. Supplied in corrosion-resistant, stainless steel housing, motors offer speeds to 44,525 rpm and continuous torque to 42.6 oz-in.

ThinGap LLC
Ventura, CA 93003
May 23, 2008 Supplied in 2.626 in. dia x 2.48 long package that weighs 30 oz, TG 2340 delivers 500 W (0.68 hp) continuous shaft output power at 48 V and 600 oz-in. peak torque. Max motor efficiency is 90%, and peak system efficiency using trapezoidal controller is 85%. Due to rigid ironless core rotor that eliminates hysteresis losses and cogging torque, motor offers smooth acceleration. Airflow over interior and exterior coil surfaces promotes optimal heat dissipation.

Bosch Rexroth Corp., Industrial Hydraulics Div.
Bethlehem, PA 18017
May 23, 2008 Designed for pavers and crawler-type machines, such as loading tractors and bulldozers, Series 71 A6VM axial piston variable motor combines nominal pressure, specific displacement, and rotational speed characteristics that ensure smooth low running-speed operation over entire swivel angle range. Sealing points of threaded connections are designed to use seal rings, while cross-flow scavenging is optimized for when motor is used as high-performance drive.

Lin Engineering
Santa Clara, CA 95054
May 21, 2008 Capable of up to 85 oz-in. of holding torque depending on stack size of motor, SilverPak 17D is 2 phase, 1.8° NEMA 17 motor with integrated microstepping driver. Available in 2.69, 2.92, and 3.24 in. body lengths, features include operating voltage range from 12-24 Vdc, phase current range from 0.25-2.0 A peak, step resolutions from full stepping to 16x microstepping, optically isolated step, direction, and disable/enable inputs, and under-voltage and over-temperature protection.

Crouzet
Coppell, TX 75019
May 20, 2008 Designed for motorization of peristaltic positive displacement pumps, PPGM Series is offered with variety of customized adaptations to meet specific requirements. It features gearbox torque of 0.5 Nm nominal and operating voltage of 24 V, and is available in 16 and 30 W models. Wide range of gear ratios from 12.80 to 104 can create output speeds from 46-455 rpm. Encoders are available on some versions from 1-48 pulses for accurate flow pump rate control.

Danaher Motion/Portescap
Radford, VA 24141
May 14, 2008 RoHS-compliant h3 Series incorporates enhancing magnets, inserted between each stator tooth, to optimize torque output across entire speed range. Supplied in aluminum housing for optimal heat dissipation, these 1.8° step motors feature Neodymium iron boron magnets as well as bearing retainer and o-ring. Larger bearings enable motor to handle higher side and radial loads. They are available in NEMA 17, 23, and 34 frame sizes, with various stack lengths available in each frame size.

ABM Drives Inc.
Milford, OH 45150
May 13, 2008 Rated 0.25-10 kW, SINOCHRON® motors are enclosed in aluminum housing and use 3-phase stator winding with rotor having permanent magnets embedded in stack. This produces sinusoidal magnetic field and even flux distribution in motor, resulting in smooth, constant-speed operation, independent of load, with no torque ripple. Exceeding EPACT 1 efficiency in fractional sizes, motors exhibit typical accuracy under 1° when coupled to gearbox or ±5° at motor shaft.

Physik Instrumente (PI)
Auburn, MA 01501
May 02, 2008 Consisting of 4 parts, Model P-653 can replace classical drive elements such as miniaturized motor/lead screw systems or other linear motors. Unit measures 8.0 mm in length with travel range of 2 mm and sub-micron resolution, combined with holding force of 0.15 N. Assembled as unit, moving slider and piezo motor are mounted on PCB driver board requiring 5 Vdc supply. Non-magnetic ceramic motor includes auto-locking feature and is suitable for limited space OEM applications.

Maxon Precision Motors
Fall River, MA 02720
May 02, 2008 Available in 2-wire and 5-wire versions with operating range of 2-50 W, Models EC 20 flat, EC 32 flat, and EC 45 flat include Hall sensors and 1-quadrant speed controller. In 2-wire version, speed acts proportionately to applied operating voltage of 10-28 V. Current limitation, under and over-voltage switch-off, and temperature monitoring are implemented as standard in all models. Motors are suitable where installation space is minimal and constant speed is required.

Nyden Corp.
San Jose, CA 95134
May 01, 2008 Five-Phase MLN50 Mechatrolink Stepper Motor and Driver Network series is 100/200 V AC Driver system that yields full programming command functions and offers communicational data rate up to 10 Mb/s and transmission range up to 50 m max. System measures 120 x 175 x 45 mm and can be empolyed in operational compliancy with patented Mechatrolink Network Controller Bus Communication Motion Link for building robotic equipment, cutting systems, and semiconductor production equipment.

Oriental Motor U.S.A. Corp.
Torrance, CA 90505
Apr 17, 2008 Respectively rated at 200 and 400 W, RoHS-compliant BLF 6200 and 6400 series provide fully programmable brushless dc motor and driver speed control package. Driver box controls brushless dc motor from 80-4,000 rpm, a speed range of 50:1, with total speed regulation of 0.6% due to specified load, voltage, and temperature variations. Programmable control feature set lets user select 3 display modes, multi-speed operation with 8 selectable speeds, and 4 speed setting methods.

Festo Corp.
Hauppauge, NY 11788
Apr 14, 2008 EMMS-ST stepper motor offers holding torque from 0.5-9.3 Nm, with external gearbox options of 3:1 and 5:1. Configurable as open- and closed-loop, CMMS-ST controller integrates braking resistor and mains filer, SD/MMC memory card, and network interfaces for Profibus and DeviceNet. There are 63 configurable positions, 8 positioning profiles with sequencing capability, and positioning profile overlapping. Combination of both handles loads of up to 20 kg.

Nanomotion
Ronkonkoma, NY 11779
Apr 14, 2008 Providing 30 g of thrust with maximum operating velocity of 150 mm/sec, EDGE motor is suited for shutter/aperture control, small medical pumps, grippers, and other devices in aerospace/military, medical devices, and industrial automation applications. Supported by Nanomotion's dual axis ASIC that can function as drive and control, ceramic servo motor is capable of driving linear or rotary motion, and operates at 8 Vrms.