Helical Gears

Mechanical Power Transmission

Bevel/Helical Gearboxes employ 2-stage design.

October 2, 2015

Primarily intended to drive logistics systems, RO2 series achieves 20 reduction ratios from 5.2:1 to 51.5:1 with 2 gear sets: bevel at input and helical at output. One-piece housing and fixing holes promote torsional rigidity to fittings. Sizes include RO02, RO12, RO22, and RO32 with respective max torque ratings of 120, 120, 330, and 550 Nm and hollow output shafts of 25, 30, 35, and 40 mm.
Read More

Mechanical Power Transmission, Green & Clean

Planetary Gear Units offer up to 5,450 kNm torque.

April 22, 2015

Available in 10 sizes with torque range from 1,700–5,450 kNm, Planurex 3 Series features compact design that enables space-saving, high transmission ratios to be achieved. Size grading is harmonized to minimize jump in power ratings between different sizes. All sizes can absorb peak loads up to twice their nominal torque. Part of Integrated Drive System, planetary gear units are typically used as roller press and central drives for tube mills in mines and cement plants. Read More

Fluid & Gas Flow Equipment, Mechanical Power Transmission

Gear Pumps transfer water to 2.6 gpm and oil to 52.9 gph.

May 10, 2013

Constructed with helical bronze gears, nickel-plated brass body, and stainless steel shaft, UP2/Oil Gear Pumps transfer both water and engine oils. UP2/P Gear Pumps, featuring PTFE gears, are suitable for transferring fresh and salt water as well as diesel fuel. All electric pumps are self-priming and measure just 4 3/8 in. in length to fit in tight spaces.  Available in 12 or 24 Vdc, pumps have motor life of approximately 2,000 hours and max operating temperature of 140°F. Read More

Material Handling & Storage, Mechanical Power Transmission

Screw Conveyors feature helical-bevel gears.

February 11, 2013

Part of Screw Conveyor Package, Right-Angle Helical-Bevel Gears are compatible with CEMA mounting and allow users to install gearboxes in confined spaces. Units produce torque levels up to 42,480 lb-in. and powers up to 30 hp. Using direct coupled gearmotor or NEMA C-face input design, series eliminates need for separate V-belt. Speed reducer housings, constructed of one solid cast-iron piece, contain bearings and seal seats, which eliminates need for splits or bolt-on carriers. Read More

Mechanical Power Transmission

Induction Hardened Rack Gears combine precision, strength.

February 27, 2012

Designed for use in pinion (spur gear) mechanisms, Induction Hardened Rack Gears feature 1045 Carbon Steel construction and create linear actuator that converts rotational motion of pinion into linear motion. RGEAH (Ground) gears offer no hole, bottom tapped, side tapped, or side counterboard tapped hole machining options, while RGEAHL (Ground, Hole Position Configurable) gears offer user-configurable hole machining with bottom, side, or side counterboard tapped options. Read More

Mechanical Power Transmission

Crossed Axis Helical Gears work together with same hand.

September 9, 2010

Accommodating everyday use, commercial crossed axis helical gears come in right hand (standard) and left hand (optional) versions. Both bossed and plain versions are standard with 214M15 steel and white delrin made to Quality Grade 9 ISO 1328. Sizes start at 0.5 Mod and increase to 3.0, with numbers of teeth depending size selected. Different numbers of teeth are available on request, along with other materials, bores, keyways, tapped and pin holes all available on request. Read More

Mechanical Power Transmission

Parallel Helical Gears are offered in bossed or plain versions.

September 6, 2010

Commercial parallel helical gears are available in bossed or plain versions in sizes from 0.5-3.0 Mod. Manufactured to Quality Grade 9 ISO 1328, gears are also available in white delrin and 214M15 steel. Modifications such as different numbers of teeth, different materials, bores, keyways, and tapped and pin holes can be specified. Accessories such as clamping sets, keys, and dowel pins are also available. Read More

Mechanical Power Transmission

Crossed Helical Gears are available to application demands.

April 2, 2010

Available from sizes 0.5-3.0 Module, 45º crossed helical gears feature right hand helix that runs with another right hand helix. Gears are manufactured to Quality Grade 7e25 DIN 58405 (AGMA Q10), and other Quality Grades are available upon request. While standard materials are 817M40T (28 HRC) steel and 805M20 (58 HRC) case hardened steel, customer-specific options include tapped holes, pin holes, different bore sizes, number of teeth, and keyways. Read More

Mechanical Power Transmission

Linear Motion Components are offered as complete assemblies.

February 16, 2010

Linear power transmission components, available as complete assembly, include diverse range of gears: spur, internal spur, helical, miter/bevel, anti-backlash, worm and worm wheel, racks, and gearing assemblies. Manufactured from stainless steel, aluminum, and plastic, gears are available in various bore sizes from 1/8-½ in. Read More

Mechanical Power Transmission

Helical Inline Drives feature sanitary design.

April 12, 2006

Part of Hub3® CleanLine UltraPlus(TM) product line, stainless steel Hub3® Drives are available in 2 models with ratings up to 18 hp. Sanitary design features smooth machined exterior surface, profiled to allow for cleanability with no places for contaminants to collect. Read More

Mechanical Power Transmission

Gearmotors/Speed Reducers operate at 95%+ efficiency.

February 12, 2002

90.1 Series helical bevel gear products are available as triple- or quadruple-reduction drives with foot, flange, or shaft mount configurations. They offer power ranges from 1/6 to 200 HP, output speeds from 0.1 to 218 rpm, torque up to 283,200 lb-in., and gear ratio ranges from 8.04:1 to over 300,000:1. Unicase(TM) housing eliminates oil leakage and contamination. Autovent sealing prevents bearing damage caused by moisture and dirt. Read More

Mechanical Power Transmission

Gearing works with standard screw.

January 17, 2002

Precision gearing works with threaded long length rods and adapts to rotary or linear motion machinery. It is capable of fine adjustment and positive positioning. Gear is available in variety of standard sizes or can be made to order. Read More

  • 1