Mariah Power
Reno, NV 89521
Jun 16, 2008 Connected to building power supply, Windspire® vertical axis wind turbine offsets electricity use and, at times, runs electricity meter backwards. Styling helps unit blend into surroundings, while technology maximizes energy conversion, regardless of wind speed. Integrated, plug 'n produce(TM) design includes generator, inverter, wireless performance monitor, and tilt-up monopole. Unit can produce about 2,000 kWh of electricity in 12 mph average winds.

Mass Megawatts Wind Power, Inc.
Worcester, MA 01605
Apr 23, 2008 Utilizing canvas panel system, Adjustable Augmenter funnels and accelerates wind into Multi-Axis Turbosystem, increasing power output. System includes side wall dump panels and top panel lift systems that minimize pressure spikes in augmenter during extreme wind events. Side panels swing open when sufficient pressure differences exist between inside and outside of augmenter, while top panel lift system allows suspension cable to lift above next panel to vent air velocity to outside of augmenter.

I POWER Energy Systems, LLC
Anderson, IN 46013-2317
Jul 14, 2006 Featuring cylinder heads that perform at 20,000 hr life-cycle span, Endura(TM) integrated systems provide on-site, continuous-duty power utilizing multi-fuel energy sources. They can produce electricity in tandem with, or independent of, utility grid systems or direct shaft power. Products are suited for fielded power generation units as well as low-emissions agricultural (AG) irrigation pumps.

Air Squared, Inc.
Broomfield, CO 80020
Apr 05, 2006 Scroll expander is designed for expansion generators used to convert waste heat energy from exhaust gases or liquid cooling systems of internal combustion engines, fuel cells, and solar collectors. Unit offers expansion ratio of 4.6:1 and displacement of 12 cc/rev. Scroll features magnetic coupling that eliminates leakage path for working fluid, weighs 20 lb, measures 11.6 x 8.2 x 9.1 in., and provide pulse-free operation with 50 db noise level.

GE Energy
Atlanta, GA 30339
Oct 12, 2005 Featuring permanent magnet synchronous generator and modular converter with full power conversion, Wind Turbines are based on force flow optimized bedplate, which joins all nacelle components on common structure. Machines rated at 2.5 megawatt feature 100 m rotor diameters, while 3 megawatt units offer 90 and 94 m rotor diameters. Pitch regulation system with power/torque control and use of drive train damper mitigate loads of larger rotor.

GE Energy
Atlanta, GA 30339
Oct 11, 2005 Rated at 1.5 megawatt, 1.5xle model features LM 40 rotor blade with 82.5 m rotor diameter that is suited for class III or weaker wind applications. Extreme cold-weather package provides for nominal operation at temperatures as low as -30°C and in survival mode without operation at temperatures as low as -40°C. Available tower heights are 58.7, 80, and 100 m, and tallest version is also available in solid steel form with no concrete foundation.

Kaydon Custom Filtration Corporation
LaGrange, GA 30240
Sep 28, 2005 Turbo-TOC® KL Series prevents oxidation and viscosity breakdown that may compromise turbine lubricant effectiveness. Combining coalescing technology with electronic touch controls, systems utilize K1100 pre-filter, K2100 coalescer, and K3100 separator to remove harmful water, particulates, and other contaminants. Along with pump pressure, element differential pressure, and oil temperature graphics, display also relays water removal data.

Dresser-Rand Co., Turbo Products Div.
Olean, NY 14760
Jun 07, 2005 Single-stage Series 400RT is available in sizes from .75–450 kW with pressures to 700 psig and temperatures to 825°F. Dual exhaust outlets are symmetrically located and can be used individually or jointly. Idealube lubrication system automatically provides flood, splash, and mist lubrication when required. Monolithic wheel design is standardized and includes stainless steel milled style blading, metallurgically combined with alloy steel wheels.

GE Energy
Atlanta, GA 30339
Feb 07, 2005 Dry Low NOx combustion system reduces NOx emissions for company's 12 MW class 10-2 gas turbine from 25 to 15 ppm. Emissions level is guaranteed over operating conditions spanning 50-100% of load and ambient temperature range of -20° to +100°F. It requires no catalytic hardware minimizing number of combustion parts. Combustion chamber incorporates 4 GE5 premixed pilot burners and includes flame detector, flashback thermocouples, and humming detection system for full flame control.

Caterpillar, Inc., Solar Turbines, Inc.
San Diego, CA 92186 5376
Dec 13, 2004 Cold-end-drive, single-shaft Taurusâ„¢ 65 generator suits cogeneration, combined cycle, and other power generation applications. Generator set is rated at 6000 kWe for continuous duty at ISO conditions. It features 13-stage axial compressor with 15:1 pressure ratio that produces air inlet flow of 19.4 kg/sec, and utilizes 3-stage turbine with shrouded stage-3 turbine blade. SoLoNOâ„¢ combustion system reduces formation of NOx and CO, eliminating post-combustion clean-up devices.

DTE Energy Technologies, Inc.
Detroit, MI 48226
Jun 25, 2003 Based on aero-derivative natural gas fired turbine, ENT 400 is designed for applications where its exhaust gas can be used for direct heating and drying applications. Product provides up to 6 MMBtu/hr of heat as direct exhaust at 27,450 lb/hr at 1013ºF and 396 kW of continuous electric power. System is fully integrated in compact container and includes all controls and utility switchgear.

Cooper PowerTools
Lexington, SC 29071
Jul 12, 2002 Dotco® 12R91 series precision turbine allows tool to idle and provides full power under load. Pre-loaded bearings maintain stability in spindle to allow for smoother cuts. Available with 3 mm and 1/8 in. collets, 65,000 rpm rear exhaust governed tool suits applications that previously used 100,000 rpm non-governed tools. It is available in models with 2 and 4 ft overhose to direct exhaust away from work area.

GE Power Systems
Schenectady, NY 12345
Jun 11, 2002 Built upon Frame 6FA gas turbine technology, Model PG6111FA offers output increase to 75.9 megawatts and heat rate improvement of 2.7% over previous model. Combined-cycle service provides 117.7 megawatt output with 54.7% efficiency. Firing temperature is rated to 2420°F and pressure ratio is 15.6. DLN-2.6 combustion system is capable of 15 ppmvd NOx. Turbine suits a variety of installations, including combined heat and power and cogeneration.

Perkins Engines Inc.
Mossville, IL 61552 0610
Apr 23, 2002 Series 800 3.3 liter, 4-cylinder engines, in 58 to 80 hp power band, is available in naturally aspirated, indirect-injection (IDI) and turbo-charged, direct-injection (DIT) versions. IDI version provides lower noise and emissions, and turbo-charged DIT version provides maximum power output while still remaining within emissions and noise targets. Series exceeds EU and North America Stage 2/Tier 2 off-highway emissions legislation.

Perkins Engines Inc.
Mossville, IL 61552 0610
Apr 23, 2002 Model 403C-11 0.10 cubic meter engine features 1.1 liter capacity and provides output power of 19.5 kW (26.1 bhp) at 3000 rpm. Three cylinder, indirect injection engine is naturally aspirated.

Cummins Engine Co., Inc.
Columbus, IN 47202 3005
Apr 19, 2002 Model B3.3 engine, in 65 hp 85 hp versions, is now certified by Mining Safety Health Administration (MSHA) for underground mining. Engine footprint fits easily into equipment, with access to all maintenance points from either left or right side. Parent bore block is rebuildable, and mechanical fuel injection delivers low fuel consumption as well as low emissions.

Cummins Engine Co., Inc.
Columbus, IN 47202 3005
Apr 16, 2002 A Series engines are available from 18-60 hp with 0.9 to 2.3 liters displacement. All have dual hydraulic pump mounts, crank-mounted PTO, variety of drivetrain mounting configurations, one-side serviceability, integrated cold-start aids, and low-noise signature. Models include three engine families with six different hp ratings and torque curves. Model numbers include A2000, A2300, A1400, A1700, and A900.

Caterpillar, Inc.
Peoria, IL 61629
Apr 10, 2002 3003C/3024C family includes 5 models of 3 and 4-cylinder engines, which operate in 12 to 45 kW power band. Operating in 50 to 130 kW power range, model 3054, 4.4 liter, 4-cylinder engine is available with naturally aspirated, turbocharged, or turbocharged with air-to-air after cooling variants. Model 3056, 6-litre, 6-cylinder engine is offered with turbocharged and air-to-air after cooling and electronic engine control.

Caterpillar, Inc.
Peoria, IL 61629
Apr 09, 2002 Model 3126B 7.2 liter, 6-cylinder engine includes ADEM(TM) III electronic control module, allowing parameters to be controlled and monitored. HEUI(TM) fuel system utilizes hydraulically actuated, electronically controlled unit injectors and allows complete, adjustment-free, electronic control of fuel injection pressure, timing and duration. Model 3126B is also available in 175 to 275 hp, and is rated 2100 to 2500 rpm.

Caterpillar, Inc.
Peoria, IL 61629
Apr 09, 2002 Model C-9, 8.8-liter, in-line, 6-cylinder, air-to-air aftercooled industrial engine offers Caterpillar ADEM(TM) III controller and HEUI(TM)-B fuel system. HEUI fuel system utilizes hydraulically actuated, electronically controlled unit injectors. The 350 hp C-9 is also available with ratings from 275 to 335 hp, and operates at 1800 to 2200 rpm for industrial applications.