Mechanical Power Transmission

Mechanical Power Transmission

Hydraulic Power Unit drives bar shears.

Jan 29, 2002

VHPI-3 Hydraulic Power Unit, suitable for use with lightweight Bar Shears, weighs 30 lbs, and can be carried from one location to another. Fluid flow ranges from 1 GPM at low pressure to reduced flow at higher pressure. Its 1/2 HP motor draws 10 amps at 110 Volts. Read More

Mechanical Power Transmission

Failsafe Brake fits stepper and servo motors.

Jan 29, 2002

Model RFEB power-off brake mounts on front end of standard NEMA 23 and NEMA 34 stepper or servo motors to prevent machine from operating or for holding load in place when power fails. It has spring-set design, ball bearing supported output shaft, and operates at speeds to 8,000 rpm. Brake is available in 24 and 90 Vdc versions. Applications include factory automation, material handling, robotics,... Read More

Mechanical Power Transmission

Spring Set Brakes hold loads when power fails.

Jan 29, 2002

ERD Series electrically-released, spring set brakes perform dynamic stopping and fail-safe, power-off braking to hold loads in event of electrical outage. Brakes are available in 8 sizes, from 3.3 to 9.9 in. dia with torque capacities from 4 to 220 lb ft. Brakes permit stopping and holding in both directions, and can stop loads from motor speeds up to 3600 rpm. Applications include hoists,... Read More

Material Handling & Storage, Mechanical Power Transmission, Waste Management & Waste Handling Equipment

Solids Reduction Unit retrofits to twin shaft grinders.

Jan 29, 2002

Annihilator twin shaft solids reduction unit is supplied with seals and bearings housed in replaceable stainless steel cartridge, which allows on-site replacement. Counter-rotating, hexagonal shaft design coupled with hardened steel cutters provide maximum shredding strength necessary to process 300 to 4,250 GPM of influent. Annihilator is fitted with toothed cutting spacers, electronic control... Read More

Controls & Controllers, Mechanical Power Transmission

Drive and Control System has single/multi-axis versions.

Jan 29, 2002

Indramat OPTIFEED-C prefigured, flexible drive and control system controls roll feed, provides digital synchronization and requires no NC programming. Control system maximizes press line's number of strokes. OPTIFEED-C offers selectable functions such as automatic feed adaptation, start-point displacement, programmable switch cam group, and setpoint output. System's firmware contains 99... Read More

Mechanical Power Transmission

Linear Drive Actuators eliminate friction and backlash.

Jan 28, 2002

Series BB 2-piece systems consist of passive, magnet-free, stationary platen, serving as precision linear guideway and moving forcer with built-in roller bearings. All bearings are magnetically preloaded and do not require gap adjustments. Units have force ranges from 5 to 15 lb, open loop motion repeatability of 0.0001 in., and travel length up to 80 in. Forcers are capable of velocities of 60... Read More

Mechanical Power Transmission

Polymer Bearings come in 1,000 varieties.

Jan 21, 2002

More than 1,000 iglide polymer metric plain bearing sizes, in sleeve, flange and thrust configurations, are available. They provide oil-free and maintenance-free operation and resist dirt and dust. Bearings are molded from polymers optimized for bearing applications. They replace bronze, PTFE coated, and metallic plain bearings. Read More

Controls & Controllers, Mechanical Power Transmission

Motor and Driver includes onboard electronics.

Jan 17, 2002

MDrive34 uses NEMA 34 frame size 1.8° motor combined with microstepping drive, and accepts up to 14 resolution settings from 1/2 to 256 microsteps per step. Setup parameters include Microstep Resolution and Run-and-Hold currents, and can be changed on-the-fly or downloaded and stored in non-volatile memory with GUI. Operating voltage is +24 to +75 VDC. MDrive34 is available in single stack,... Read More

Mechanical Power Transmission

Feedthrough Actuator provides motion control in vacuum.

Jan 17, 2002

Chamberlink, single-unit combination feedthrough and servo actuator, allows output shaft to operate in vacuum without shaft seals, preventing leaks. It is available in sizes 10, 14, and 32, with output torques from 10 to 300 in.-lb and output speeds of 10 to 50 rpm. Actuator is rated for vacuum levels of 10E-8 Torr. Read More

Mechanical Power Transmission

Corrosion Resistant Actuators work in food processing.

Jan 17, 2002

CR Series actuators resist sulfur dioxide atmosphere, sodium chloride mist spray, and water condensation. Five models are available: CRDNG and CRDNGS conform to ISO 6431 and VDMA 24562 standards, have piston dia from 32 to 100mm and stroke lengths between 10 to 2000mm; CRDNG has integrated swivel flange for clevis mounting. CRDSNU and CRDSW are slim-line actuators with round-section barrel for... Read More

Mechanical Power Transmission, Optics & Photonics

Belt-Driven Boom positions robots and gantries.

Jan 17, 2002

DGEA toothed-belt-driven electric boom-arm axis is suitable for positioning applications requiring horizontal or vertical projecting motions. Fixed pinion drive mechanism engages stationary toothed belt, causing projecting structure to traverse work envelope. Roller guide bearing system is integrated into housing. Unit has stroke range of 100-1,000 mm, payload of 110 lb, speed of 2.1 m/sec, and... Read More

Mechanical Power Transmission

Pneumatic Actuator works like human muscle.

Jan 17, 2002

Type MAS Fluidic Muscle uses material deformation and flexure to achieve linear motion. Basic concept involves wrapping flexible hose with non-elastic fibers arranged in rhomboidal fashion. This results in 3D grid pattern. When compressed air is introduced into system, grid pattern is deformed, pulling force is generated in axial direction, and muscle shortens. Range includes 10, 20 and 40 mm... Read More

Mechanical Power Transmission

Actuators offer short overall length.

Jan 17, 2002

Compac Series 300 and 1000 Acme screw actuators have die-cast aluminum power heads and zinc-plated inner and outer tubes. Compac 300 Torque Limiter model, with 12 in. stroke, is less than 20 in. long. Series 300 models withstand 1,000 lb static load and move loads up to 300 lbs. Series 1000 models withstand 5,000 lb static load and move loads up to 1,000 lbs. Stroke lengths range from 4 to 24 in.... Read More

Mechanical Power Transmission

Gearing works with standard screw.

Jan 17, 2002

Precision gearing works with threaded long length rods and adapts to rotary or linear motion machinery. It is capable of fine adjustment and positive positioning. Gear is available in variety of standard sizes or can be made to order. Read More

Mechanical Power Transmission

22mm DC Motor promotes heat dissipation.

Jan 17, 2002

LO-COG 22mm brush-commutated DC motor is 1.900 in. in length and employs 5-slot armature design and bonded neodymium iron boron magnets. It is suitable for mass data storage and semiconductor processing equipment. Standard cartridge assemblies prolong brush life by maintaining optimum brush force. Read More

Mechanical Power Transmission

Stepping Motor Drive IC operates in -20 to +75° C range.

Jan 14, 2002

Model FAN8200 2-channel drive IC is manufactured using bipolar process. Integrated dual H-bridge drivers with vertical PNP power transistors result in low saturation voltage (0.4V @ 0.4A) and optimum thermal characteristics (Vcc = 2.5V ~ 7.0V). Unit features built-in shoot-through current protection and thermal shutdown (TSD) function. FAN8200 accommodates 3.3 or 5V MPU control input, and... Read More

Mechanical Power Transmission

O-ring Belt is designed for powered-roller conveyors.

Jan 14, 2002

Long-Life HT Red Belt is suitable for curved, inclined and merge conveyor applications that require additional driving force to turn rollers, move loads and maintain smooth operation. It has 25% more urethane than standard 3/16 in. dia belts, yet fits into same powered-roller grooves without protruding above roller's surface, so no refitting is needed. Read More

Mechanical Power Transmission

Elastomeric Couplings feature 347 cast stainless steel ring.

Jan 11, 2002

Jaw In-Shear (JIS) 6-Pin elastomeric couplings are non-lubricated, drop-in replacements for grid spacer couplings. Converting to in-shear service doubles standard Jaw Coupling's angular misalignment capability to 20 and its parallel misalignment capability to 0.030-0.094 in., depending on size. Units fill BSE (Between Shaft End) gaps of 3.5, 5, 7, and 9 in., with maximum bores up to 5.5 in.,... Read More

Mechanical Power Transmission

Couplings enhance high-speed automation.

Jan 08, 2002

Safety Couplings provide jam-free accuracy for inserting, stacking, bundling and storage/retrieval operations. They are designed with Belleville spring, and disengage in 2 to 4 ms in jam situations. Torque-limiting couplings incorporate precision roller guides and ensure zero-backlash motion control. They are available in bore sizes from 0.25 to 3.50 in. with torque capacities from 9 to 14,160... Read More

Mechanical Power Transmission

Motor-Driver Packages are available with size 34 motor.

Jan 07, 2002

CSK Series features size 34, 2-phase, hybrid stepping motor and compact board level driver. Holding torque values vary from 305 oz-in. for CSK296-ATA to 916 oz-in. for CSK2913-ATA stepping motors. Driver packages produce drive currents of 4.0 and 4.5 A per phase. They include automatic current cutback function. Step angle select switch allows user to select full step (1.8°) or half step... Read More