SKF Motion Technologies    Lansdale, PA 19446
Dec 12, 2005 Incorporated into in-vitro diagnostic (IVD) instruments as fully integrated plug-and-play units, PICO linear stages enable controlled linear movement. Construction features extruded aluminum base, stainless steel cover, and axes designed for cross-table assembly. Along with integrated drive and guidance mechanisms, products are available in 60 and 80 mm sizes, with 5 standard stroke lengths for each size. Travel speeds are rated to 500 mm/sec.

FAG Bearings Corp.    Danbury, CT 06813 1933
Dec 12, 2005 Available with bore sizes from 320 mm radial and 220 mm axial, X-Life Spherical Plain Bearings feature ELGOGLIDE lining, which consists of fabric made from PTFE and support fibers embedded in resin. Lining offers wear resistance and ability to run dry or unlubricated, even with reciprocating motion. Since bond between sliding liner and support body is moisture resistant, X-Life large bearings are suitable for hydraulic steel structures.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 08, 2005 Designed for ¼ in. belts, .080 pitch MXL Series A6D16 is made of clear iridite aluminum alloy and available with 12-72 grooves in double- or no-flange types. Bore sizes range from .125-.250 in., and ODs range from .286-1.813 in. Fairloc® integral hub fastening design eliminates need for separate hub clamp devices, and offers benefits of frequent position adjustment, while adding positive metal-to-metal fastening strength along hub surface.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 08, 2005 Comprised of 34 HTD® pulleys made of clear anodized aluminum alloy, A 6D23-(inch) and A 6D23M (metric) Series double flange type timing belt pulleys have 3 mm pitch and are designed for .236 in. belts. Fairloc® integral hub fastening design adds positive metal-to-metal fastening strength along entire hub surface. Products, available from stock in 10-44 grooves, come in bore sizes from .125-.250 in. and 3-6 mm, with ODs from .346-1.624 in. and 8.8-41.2 mm.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 08, 2005 Comprised of 88 flexible couplings, S50MS series features single-piece aluminum or stainless steel construction with cuts to allow for common types of shaft misalignment. Products are offered in split hub, keyway, or set screw hub mounting styles with bores from .1250-1.000 in. and ODs from .315-2.48 in. With max angularity from .5° to 2° and max eccentricity from .002-.008 in., couplings are suited for applications from encoders to test equipment.

J. W. Winco, Inc.    New Berlin, WI 53151
Dec 08, 2005 Available in threaded stem or tapped type models, Self-Lubricating Rod End Bearings control and link mechanisms in all types of machines. Units feature zinc-plated steel rod end body, bronze external ring, and ball socket made of 100 Cr6 bearing steel, hardened and ground. With operating temperature of -22 to 300°F, bearings are suited for high-load, low-speed applications with hanging angles, or those that require linear, rotational, or oscillatory motions.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 08, 2005 Comprised of 48 models, S52FCY Series is manufactured in inch and metric sizes to extend shafts to same or different diameters. Hub end of coupling features Fairloc® integral hub fastening system, which eliminates marred shafts. Made of 303 stainless steel, extenders offer zero backlash and are readily adjustable on shaft. They are designed to fit shafts from .120-.500 in. (3-12 mm) dia on female side and .1250-.500 in. (3-12 mm) dia on male side.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 08, 2005 Comprised of 45 couplings offered in inch and metric sizes, S51FCZ Series joins shafts from .0900-.2498 in. (2.5-12 mm) dia. Inch to metric or metric to inch couplings are also available. Made of 303 stainless steel, zero backlash couplings are readily adjustable on shaft and feature compact, self-contained Fairloc® hub fastening system, which eliminates marred shafts while adding positive metal-to-metal fastening strength along both hub sections.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 08, 2005 Flexible shafts, available as A 7C13-(inch) and A 7C13M (metric) Series, are designed to be panel mounted without casing. Products operate in manual mode and are offered with curvature radius from 20-1.5 in. (500-38 mm). Diameters range from .130-.187 in. (3.3-4.8 mm), and lengths vary from 3-14 in. (76-355 mm).

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 07, 2005 Self-lubricated Series S99PS3 and S99PS4 include Frelon lined plain and flanged sleeve bearings that can tolerate up to 1,500 psi over portion of bearing carrying load. Frelon liner material replaces oilite and plastic materials and is impervious to most industrial chemicals and acids. Available in inch sizes to fit shafts ranging from 3/16-¾ in. diameter, bearings range in length from .25-1.00 in. with ODs from 5/16-1 in.

Beswick Engineering Co., Inc.    Greenland, NH 03840
Dec 07, 2005 Beswick 1 in. bore cylinders are made from brass or stainless steel with clevis style tail. Long-life linear actuator has piston rod supported with 2 composite bushings: one in nose, and other in tail assembly. Separated bushings adequately support couples induced by side loads and/or stress reversals. Rebuildable products feature dynamic lip seals with U-shaped cross section and do not require lubricated air supply. Force factor is 0.78 in extension and 0.70 in retraction.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 07, 2005 Available in inch and metric styles, Neo-Flex Series S50F and S50P offer shaft-to-shaft insulation and are designed to fit 3-6 mm shafts or .1200, 1/8, 3/16 and ¼ in. shafts. Center of couplings is 73 durometer molded Neoprene along with 303 stainless steel hubs. Pin type hubs use set screw for fastening, while Fairloc® integral hub fastener eliminates marred shafts and permits frequent phase adjustment, as well as timing and position adjustment.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 06, 2005 Manufactured of 300 Series clear-passivated stainless steel, .1475 pitch A 6X 7-14 Series operates with single strand ladder-chain types as well as with miniature chains. Series, comprised of 17 models, is available with pitch diameters from .340-2.255 in., ODs from .392-2.307 in., and bore diameters from .0937-.250 in. Sprocket widths range from 11/32-13/32 in., and hubs contain tapped hole for set-screw retention of sprocket onto shafts.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 06, 2005 Made of Kevlar-reinforced polyurethane, Series A6B16-D offers positive, non-slip power transmission without vibration, chatter, or backlash. Double-sided tooth action enables belts to wind between pulleys to synchronize shaft rotations. Capable of operating in temperatures from 0-180°F, and intermittently to 248°F, belts are available in widths of 1/8, 3/16, ¼, and 3/8 in. with 132-500 grooves/belt and pitch lengths from 10.56-40.00 in.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 06, 2005 Made of nylon-covered, fiberglass-reinforced neoprene, A 6R3-C timing belt stock can be spliced to suit designs where nonstandard endless belts are not available. It comes in 3 belt widths and operates continuously in temperatures from -30 to +185°F. Produced with 1/5 in. pitch and trapezoidal teeth on one side, product provides positive, non-slip power transmission without vibration, tool chatter, or backlash. It can also wind between pulleys to synchronize shaft rotations.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 06, 2005 Splines, offered as carbon steel C-12L14 Series A 1C25 or stainless 416 annealed A 1Y25 Series, permit sliding between mating members in axial direction. Shafts contain 16 external spline teeth, and stock lengths of splined shafts range from 1-6 ft. Splined bushings contain 16 internal teeth and are offered as carbon steel A 1C26 Series or stainless 416 annealed A1Y26 Series. Bushing ODs range from .625 in. to 1.500 in., and bushing lengths range from .40-1.5 in.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 06, 2005 Utilizing endlessly recirculating balls, inch-size S99L Series is comprised of standard- and heavy-duty types, which are offered in open, closed, and adjustable styles. Bore sizes range from .375-1.500 in., with dynamic load capacities of 52-663 lbf and static load capacities of 72-1,214 lbf. Sleeves and balls are made of AISI52100 Steel and are hardened to RC 60-64. Overall lengths range from .875-3 in., and ODs range from .625-2.375 in.

Sterling Instrument    New Hyde Park, NY 11042-5416
Dec 06, 2005 Oil-impregnated, sintered bronze A 7Z42 Series comes in 5 sizes with bearing ID from .188-.501 in. Max heights vary from .425-.670 in, and max radial loads range from 140-600 lb. Max speed runs from 5,100-13,500 rpm, and operating temperature is -20 to +200°F. Teflon®-filled acetal A 7Z45 Series includes 5 sizes with bearing IDs from .189-.501 in. Max radial load ranges from 48-320 lb, and max speed runs from 4,630-2,180 rpm. Operating temperature is -40 to +180°F.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 06, 2005 Available in 34 plain and flanged inch models, Series A7Y55-E is made of 440C stainless steel and offered in 9 bore sizes from .0469-.3125 in. diameter with outer ring diameters from .562-.6250 in. Inner ring widths range from .0937-.2272 in. with outer ring widths of .0625-.1960 in. ABEC 3 class bearings provide dynamic load rating of 17-159 lb and static load rating from 6-70 lb. Three lubrication options include 1 commercial and 2 to MIL spec standards.

SDP/SI (Stock Drive Products/Sterling Inst)    New Hyde Park, NY 11042 5416
Dec 06, 2005 Available in both 303 stainless steel and 2024 anodized aluminum, 0.5 Series S12N05M Hubless Spur Gears have bore diameter of 10 mm and are stocked in 3 and 5 mm face widths. Featuring 20° pressure angle, metric units range from 16-97 mm in diameter and include 30-192 teeth.