SIE Computing Solutions, Inc.
Brockton, MA 02301
Nov 06, 2009 Configurable for variety of liquids, including polyalphaolefin and ethylene glycol/water mixture, 720 Series suits high thermal load systems, based on VPX technology. Cooling side panels are configurable for either front or rear coupler access. Line-replaceable unit features avionic approved field changeable/replaceable components and low MTTR. Product can be installed onto tray with precision blind-mate drip-less connection, in combination with mating liquid avionics tray.

Synopsys, Inc.
Mountain View, CA 94043 4033
Nov 05, 2009 Designed for smartphones, mobile Internet devices, and netbooks, DesignWare® USB 2.0 picoPHY IP supports Battery Charging v1.1 specification, which allows mobile devices to draw up to 1.8 A of current when connected to wall charger. By supporting USB On-the-Go v2.0 specification, DesignWare USB 2.0 picoPHY incorporates Attached Detection Protocol feature, which optimizes power efficiency of portable devices that communicate directly to USB peripherals without need for PC host.

Tensilica, Inc.
Santa Clara, CA 95054
Nov 02, 2009 Starting at size of 15,000 gates, 32-bit Xtensa 8 consumes less than 0.05 mm² in 40 nm process technology with power dissipation starting at 10 µW/MHz. Unit includes pairs of 32-bit GPIO, 32-bit Queue interfaces for direct connection to RTL blocks, and double-precision floating point accelerator option. Customizable device is suited for mobile phones and other portable electronic devices, DTV, broadband set-top boxes, computer, storage, networking, and communications equipment.

Synopsys, Inc.
Mountain View, CA 94043 4033
Oct 26, 2009 Available in process technologies from 90 nm down to 40 nm, DesignWare HDMI(TM) transmitter and receiver digital controllers and PHY IP solution supports high-bandwidth digital content protection. It offers comprehensive set of IP deliverables that help designers embed complex interface into next generation multimedia SoCs. Solution includes optimized analog front end to support longer HDMI cables, configurable RTL, built-in termination resistors, and choice of video and audio interfaces.

HARTING, Inc. Of North America
Elgin, IL 60123 5538
Oct 20, 2009 Made of stainless steel, Han-INOX® housing series is available in Han® 10B and 3A sizes and suited for food and beverage, pharmaceutical, and processing technology industries. IP65/67-protected connections allow use under harsh conditions for data transfer or energy supply. Resistant against chemical and other aggressive substances, products ensure reliable operation in demanding external environments.

Continental Fan Mfg. Inc.
Buffalo, NY 14215
Oct 16, 2009 Available in 9 sizes from 7-18 in. dia, backward curved airfoil (BCA) impellers are optimized for quiet and efficient operation via high-strength GRP polyamide material and tight balance tolerance. TEK impeller combines precision injection molding techniques with high-strength plastics to produce a wheel stronger than steel at half its weight. Other features include non-overloading power characteristics as well as matching inlet cones.

Visiontron Corp.
Hauppauge, NY 11788
Oct 13, 2009 Featuring integrated Hand Sanitizer for Retracta-Belt(TM) queuing at public facilities, Sanitation Station comes in 2 standard packages. Model SAN-301-BA-BK includes 40 in. tall Black Aluminum Retracta-Belt(TM) Post, Purell TFX touch-free hand sanitizer dispenser with bracket, 1,200 ml Purell instant sanitizing gel, and 3 C batteries. System is available as complete sanitation station or as add-on that screws into top of any existing Retracta-Belt or Sign Post with no additional tools.

National Instruments Corp.
Austin, TX 78759-3504
Oct 09, 2009 Measuring 16 x 9 x 9 cm, 4-slot cDAQ-9174 and 8-slot cDAQ-9178 CompactDAQ Chassis contain 4 counters and utilize C Series modules for measurements such as temperature, strain, voltage, current, sound, and vibration. Engineers can take mixed-sensor measurements at different rates instead of implementing single-rate sampling. Featuring external BNC triggers, cDAQ-9178 enables user to synchronize CompactDAQ system with external device or another system without installing digital module.

Eriez Magnetics
Erie, PA 16514
Oct 09, 2009 Offered in 3 standard housing sizes, PM Rare Earth Grate-in-Housings remove fine ferrous contamination from plastic pellets, flake, and regrind prior to injection molding machine, extruder, or compounding equipment. They can even capture and hold pellets with encapsulated ferrous particles, optimizing prevention of equipment damage and downtime. Supplied in stainless steel housing, products feature 2 banks of Rare Earth permanent magnets with 250°F temperature capability.

Schaeffler Group USA, Inc.
Fort Mill, SC 29715
Oct 08, 2009 Featuring no metal-to-metal contact, HLE Series Hydrostatic Linear Guides are suited for linear motion applications in which damping must take place at point where load is applied. Guide carriages move on thin cushion of high pressure fluid, resulting in zero wear of guideways. With damping value higher than 470,000 kg/sec, Size 45 model operates at 100 bar nominal pressure with oil viscosity class of ISO VG 46 and carriage flow rate of 1.2 lpm.

Igus, Inc.
East Providence, RI 02914 0349
Oct 06, 2009 DryLin SLW Pre-Loaded utilizes antibacklash nuts, which minimize axial clearance, and includes DryLin W turn-to-fit linear bearings, with radial clearance adjustable via Allen wrench. Setscrew makes audible clicking sound with every increment of adjustment. System is lubrication-free and contaminant-resistant and features high torsional stiffness.

Synopsys, Inc.
Mountain View, CA 94043 4033
Oct 06, 2009 Supporting Low Voltage DDR3L specification that runs at 1.35 V, DesignWare® DDR3/2 PHY and Digital Controller IP targets digital home, digital office, data center, and storage applications that require bandwidth in excess of 1,066 Mbps per pin. IP includes PHY Utility Block with built-in data training circuits to enable in-system calibration. As part of data training sequence, DDR3/2 IP features ability to remove bit-to-bit timing skew that can occur on chip, in package, or on circuit board.

iwis drive systems, LLC
Indianapolis, IN 46268
Oct 05, 2009 Suited for nearly all conveying tasks that require flat transport surface, Flexon Flat Top Conveyor Chains are available in plastic and stainless steel versions as both linear and curved tracks. Low-contamination materials fulfill hygiene requirements in beverage and packaging industry. Resistant to chemicals, plastic chains can be cleaned with agents that are either unsuitable for metal chains or would require intensive maintenance.

CyberResearch, Inc.
Branford, CT 06405 2932
Oct 02, 2009 Featuring internal sound dampers that reduce chassis noise by 24-28 dB, RCQ MX-400 3U rack mount chassis incorporates advanced thermal monitoring that detects temperatures at 2 points and tracks performance of up to 8 cooling fans. Motherboard-ready chassis has front access to 6 shock-mounted drive bays: four 5.25 in. and two 3.5 in., and includes DVD-RW drive and 2 internal vertical 3.5 in. bays. Depending on selected motherboard, 5-7 expansion slots are offered.

SKF USA, Inc.
Kulpsville, PA 19443
Sep 30, 2009 Targeting linear motion applications, SKF® LLT Profile Rail Guides have sealed design consisting of double-lip front seals and side and inner seals to prevent contamination and retain lubricant. Guides are supplied pre-lubricated with integral reservoirs to deliver constant relubrication. Available in rail sizes ranging from 80-400 mm, guides feature 4 ball rows in 45° angle with equal loading capacity from all directions, which contributes to self-aligning capabilities.

Visiontron Corp.
Hauppauge, NY 11788
Sep 29, 2009 Designed for traffic control, cone mountable Skipper Retracta-Belt(TM) consists of highly visible tape that extends up to 29 ft, 6 in. Molded design is constructed of polypropylene with glass-filled nylon that will withstand harsh environments. Able to accept sign frame while receiving belts from any direction, Skipper is suited for petroleum transporters protection, construction sites, airports crowd control, parking garages, and manufacturing facilities.

Giga-tronics, Inc.
San Ramon, CA 94583
Sep 18, 2009 Models 8300 and 8400 come with LAN and IEEE-488 interface and built in resource manager. Model 8300 has 4 card slots with support for ASCOR line of 3000 Series switch modules, while Model 8400 has 8 card slots which support ASCOR line of 4000 Series high-density switch modules. Model 8400 allows for internally inter-connection of switch modules through 32 single-channel or 16 differential-channel analog bus. Connection allows large switch systems without external cabling.

Tyco Electronics Corp.
Harrisburg, PA 17105-3608
Sep 17, 2009 Made from UL 94 V-2 and V-0 flammability rated nylon resin in black or natural, single position receptacle housing is designed to insulate .312 series FASTON receptacles. Housing has contoured thumbprint pushing surface that allows operators to easily recognize proper orientation for receptacle loading and mating. Protected internal terminal locking feature provides secure retention, and includes anti-reverse component to reduce possibility of improper terminal assembly.

Parker Hannifin Corp.
Cleveland, OH 44124-4141
Sep 10, 2009 Lightweight and flexible, Partek Wrap is made from urethane-coated 1050 ballistic nylon with tight weave pattern that prevents fabric ends from fraying when cut. Abrasion-resistant sleeve can be used to bundle multiple hoses/cables together or to protect cylinder rods from damage and contamination. Available in 4 models with circumferences from 9.40-22.00 in., wrap comes on 50 ft roll and has ambient temperature range of -60 to 200°F.

Tyco Electronics Corp.
Harrisburg, PA 17105-3608
Sep 07, 2009 Connector latch locking collar accessory can be applied to mated SOLARLOK solar cable connectors to prevent inadvertent or accidental unmating. Specifically, it prevents access to release mechanism of mated connectors and allows tooled extraction via screwdriver. Collar, required in any accessible photovoltaic locations in U.S. where mated cable connectors are exposed, meets recommendations of 2008 NEC section 609 as well as UL 1741 photovoltaic requirements.