Network Technologies, Inc. (NTI)    Aurora, OH 44202
Jun 17, 2013 Featuring clamping jaw and holder with felt padding to protect surfaces from scratches, C-Clamp and Floor Stand Tablet Arms provide hands-free application and stationary support for tablets that range in height from 5–11 in. and weight up to 2.2 lb. ARM-CC-TABLET-S C-Clamp Tablet Arm has max height of 25 in., min height of 8 in., and horizontal extension of 21 in., while ARM-FL-TABLET Tablet Floor Stand has max height of 59 in., min height of 28 in., and horizontal extension of 20 in.

Synopsys, Inc.    Mountain View, CA 94043 4033
Jun 04, 2013 Featuring base board and daughter card, DesignWare® ARC® EM Starter Kit provides platform for rapid software development and code porting, as well as software debugging and system analysis for ARC EM processors. Daughter card features Xilinx Spartan®-6 LX45 FPGA, 125 MHz clock generator, 128 MB DDR3 memory, and 16 MB flash memory, while board allows multiple connectivity and configurable I/O options. Four pre-installed FPGA images for ARC EM4 and EM6 processors enable choice of configuration.

AVX Corp.    Raleigh, NC 27604
May 20, 2013 Suited for portable communications devices, DB0603N thin-film, 3 dB, 90° couplers come in surface-mountable, 0603 size LGA package; have 800–6,000 MHz range; and provide 10 W continuous power handling. Package contributes to minimal profile and parasitics characteristics and also lends to optimal solderability and heat dissipation as well as self-alignment during reflow. RoHS compliant couplers also feature construction ruggedized for reliable automatic assembly.

APM-Hexseal Corp.    Englewood, NJ 07631
May 16, 2013 Using low durometer rubber and providing very little or no resistance to actuator, Ultra Flex Bellow Toggle Switch Boot 1131/60 guards against accidentally tripping breaker/switch into on/off position. Boot provides UL recognized sealing performance that meets NEMA 4, 4X/IP68 sealing standards.
 

Gooch & Housego    Somerset TA19 0AB  United Kingdom
May 16, 2013 Without requiring customization or fundamental redesign, Universal Integrating Sphere series is designed to accommodate variety of configuration and application requirements. Various combinations of sphere sizes, coatings, number of ports, as well as port designs and diameters can be coupled with variety of accessories and adapters, allowing users to custom tailor sphere to specific needs or modify it as requirements change.

Kurt Manufacturing    Minneapolis, MN 55421
May 14, 2013 Engineered for locating, attaching, and removing fixtures, subplates, and vises on machining centers, PinLock™ System consists of high-precision pins, bushings, and liners that provide locating and locking repeatability up to ±.0005 in. Shanks and bushings are precision machined of heat-treated, alloy steel with black oxide finish. Helical extraction design and pin feature aids in overcoming binding in side load conditions and optimizes removal of PinLock in any application.

iWave Systems Technologies Pvt, Ltd    Bangalore 76  India
May 10, 2013 Providing interface between PCI bus and user interface, PCI Controller supports variety of initiator commands and functions, including configurations read/write; memory read/write, memory read multiple and memory read line; I/O read/write; parity generation and parity error detection. PCI core interface is processor independent, enabling transition to future processor generations. PCI Controller is suited for desktop and departmental servers as well as graphics and multimedia applications.

Lian Li    Keelung   Taiwan
May 01, 2013 Model PC-Q27 Mini-ITX chassis measures 7.8 x 11.8 x 9.4 in. and supports graphics cards up to 7.6 in. Brushed aluminum unit accommodates up to three 3.5 in. hard drives and features I/O panel with 2 USB 3.0 ports. Measuring 8.9 x 12.0 x 13.5 in., model PC-Q28 holds graphics cards up to 11.4 in. long and up to 7 hard drives, while drive cages are removable. Product has front fan with dust filter and top fan to remove hot air. Both units include front and rear feet stands to sit up off ground.

CEVA, Inc.    San Jose, CA 95110-3710
May 01, 2013 Android Multimedia Framework (AMF™) addresses intensive, real-time signal processing applications, including audio, voice, imaging, and vision, and seamlessly offloads related tasks from CPU to CEVA DSPs at Android OS level. Heterogeneous CPU and DSP system architecture reduces power consumption required for complex multimedia processing. Availability covers CEVA-TeakLite-4 audio/voice DSP, CEVA-MM3101 imaging and vision platform, and CEVA-X general purpose DSP.

Mini-Circuits    Brooklyn, NY 11235
Apr 30, 2013 With range of 610–810 MHz, SYBD-22-82HP+ 50 Ω, 22 dB coupling, DC pass units feature mainline loss of 0.10 dB typ with VSWR of 1.10:1 typ and deliver directivity at 24 typ. Select models feature power handling capabilities to 150 W at room temperature, and suitable applications include VHF/UHF and SMR. Model SYBD coupler series joins LTCC coupler family with rugged connectorized models. All couplers are ESD compliant and available as RoHS compliant.

Andes Technology    Santa Clara, CA 95054
Apr 30, 2013 Available in sizes as small as 12K gates, AndesCore™ N7 (Hummingbird) 32-bit processor series implements AndeStar™ V3m architecture in 2-stage pipeline for optimal efficiency of 108 DMIPS/mW. IP cores come with complete software development environment and libraries and incorporate mechanisms that provide for acceleration of applications that utilize higher-latency flash memory. Products in this series are fully supported by integrated GCC tools environment.

Interstate Specialty Products    Sutton, MA 01590
Apr 24, 2013 ISP Custom Extruded Rubber Shapes can be made from range of materials and with specific profiles to exactly match gasket and seal application design requirements relative to geometry, function, assembly, and manufacturing. Available in solid, hollow, and sponge profiles, rubber extrusions can be supplied in 1 in. cuts up to 100 ft spools. Products include round, square, rectangle, strip, edge trims, fenders, U-channel, and D-, P-, L-, and E-shapes in any size.

Slideways, Inc.    Worcester, MA 01605
Apr 23, 2013 Compliant with Food Safety Modernization Act, X-Ray Detectable Components help minimize contamination problems for food industry. Products such as wear strips, sprockets, chain guides and tracks, mixer components, bushings, and bearings are available in Acetal, UHMW, Nylon, and PEEK. Detection of parts as small as 2 mm³ at speeds as fast as 250 fpm is standard.

Alsa Corp.    Vernon, CA 90058
Apr 19, 2013 Offered as siding and decorative metal solution, 4EverBright combines colored real pure copper with lightweight aluminum construction and protective properties of Lexan polycarbonate resin thermoplastic. Layer of Lexan® polycarbonate resin thermoplastic prevents exposure to humidity and air, preventing pure amber hue from ever fading or tarnishing, and also protects copper against scratches and dents. Sheet comes in various thicknesses, including .040, which is traditional to roofing.

FCI Electronics    Etters, PA 17319 9769
Apr 03, 2013 Intended for telecom, datacom, and military applications, multi-mode and single-mode optical tap, splitter, and star couplers feature simplistic connector terminations and come in ruggedized housings that isolate fused fiber area. Miniature 2 x 12 channel (TX=RX) single on-board transceiver system supports next generation Infiniband and Ethernet standards as well as other emerging intra box optical/electrical specifications. There are 2 low-profile pluggable electrical connector options.

POLYCASE    Avon, OH 44011
Mar 20, 2013 Offered in 3 styles and 5 sizes from 5.11 x 3.93 x 2.75 in. to 11.81 x 7.87 x 6.29 in., WH Series supports 0.06 in. thick aluminum mounting panels that attach directly to mounting bosses inside base using included screws. Panels let electrical engineers mount hardware inside enclosure without puncturing exterior, maintaining NEMA 4X rating of box. Hinged cover is standard, and panels can feature cutouts, including threaded holes, per customer specifications.

Thomas & Betts Corp.    Memphis, TN 38125
Mar 13, 2013 Consisting of wire rope and self-locking cable-grip fastener, Kindorf® Fast Cable Link requires no tools for installation. Serrated locking rollers provide extra non-slip grip, while release pin enables adjustment after inserting wire rope into fastener, and stainless steel springs keep locking roller in constant contact with wire rope. Made of zinc alloy, fastener is constructed with riveted connections for strength. Wire rope is zinc-plated steel for corrosion protection.

Bishop-Wisecarver Corporation    Pittsburg, CA 94565 0209
Mar 08, 2013 Completely seamless and free running, HepcoMotion® PRT2 1-Trak eliminates possibility of misalignment during installation or in service. Entire track element is manufactured from single piece of steel, with or without base plate, and features 3-bearing wheel plate. Wheel plates can carry loads from 67–51,000 N, and tracks can be made up to 5.5 x 1 m or 1.9 m square. Track systems can be specified with vee profile guide section of any size to suit bearings from 13–150 mm in diameter.

ABI Inc.    New York, NY 10006
Mar 05, 2013 Made of non-woven nylon impregnated with abrasive grain and smear-free resin, Norton Rapid Prep surface conditioning discs suit such surface finishing applications as removing surface defects, oxides and corrosion, deburring, mold cleaning, and blending uneven edges and marks. Products work with right-angle grinders, in-line grinders, and die grinders and have open structure that resists loading on softer materials while optimizing surface finishing results on hard materials.

Larson Electronics, LLC    Kemp, TX 75143
Feb 20, 2013 Powered by included 1/3 hp compressor, telescoping PLM-18 lets operators safely deploy and elevate lighting and electrical equipment without use of hand winches or cranks. All wiring is mounted internally within 6-wire harness, with 12 in. of wiring extended from both ends for connecting power sources and devices. Stable in windy conditions, 300 lb tower safely supports up to 150 lb of equipment and installs onto truck beds or mounting platforms via 12 x 12 x ½ in. mounting base-plate.