Other

Materials & Material Processing

Drilling Compound has copper appearance and texture.

April 28, 2016

Applicable over wide temperature range and diverse working conditions, HONEY KOTE™ maximizes protection against seizing, galling, and load-bearing stress on drill collars and drill pipes used in oil and gas industry. Product, pressure tested up to 25,000 psi, meets/exceeds all ISO and API standards and will not run off or bleed at high temperatures or harden in storage. Formula's protection against corrosion and water wash-out increases efficiency. Read More

Chemical Processing & Waste Management, Materials & Material Processing

Air Products to Feature Nitrogen and Oxygen Supply Systems for Laser Assist Gas at LME 2016

April 26, 2016

LEHIGH VALLEY, Pa., - Air Products (NYSE: APD) understands that a reliable assist gas supply is critical to keep a laser cutting operation running without interruption. For this reason, the company offers a full spectrum of nitrogen and oxygen assist gas systems, which the company will feature at the Lasers for Manufacturing Event (LME) 2016 in Atlanta from April 26-27. Laser operators are... Read More

Materials & Material Processing, Green & Clean

Air Products to Highlight Industrial Gases and Related Technologies for Pharmaceutical and Biotechnology Industries at INTERPHEX 2016

April 26, 2016

LEHIGH VALLEY, Pa., - Air Products (NYSE: APD) will illustrate the value the company can provide to the pharmaceutical and biotechnology industries through its reliable industrial gas supply and advanced gas technologies at INTERPHEX 2016 in New York City from April 26-28. INTERPHEX attendees are invited to stop by booth 2464 to discover the many ways Air Products' industrial gases and... Read More

Fluid & Gas Flow Equipment, Materials & Material Processing, Mechanical Components & Assemblies

Cope Plastics, Inc. Offers Limited Time Free Shipping for Online Inventory

April 25, 2016

Cope Plastics, Inc., the premier distributor and fabricator of plastic sheet, rod and tube in the Midwest, headquartered in Alton, Illinois is pleased to announce limited time free shipping on all online inventory at http://store.copeplastics.com/. This applies to standard 3-5 day shipping on all online orders. This online store which launched in... Read More

Materials & Material Processing

Polyurethane Potting Compound cures in 1 hour.

April 22, 2016

Designed to cure within 1 hour at room temperature, 20-2183 features 2:1 mix ratio and low viscosity that makes it suitable for use in cable assemblies, potting electronics, molding parts, and encapsulating electronic components. Tough elastomeric material helps assemblies withstand thermal cycling, offers vibration resistance, and imparts low stress on electronic components during cure. Resistant to moisture, compound may be used in wet environments and outdoor applications. Read More

Materials & Material Processing, Green & Clean

Rheology Modifiers increase paint formulation versatility.

April 15, 2016

Featuring low-VOC, solvent- and surfactant-free, hydrophobically modified ethylene oxide-based urethane (HEUR) chemistries, ACRYSOL™ RM-1600 and RM-3030 improve surface aesthetics and hiding across range of binder chemistries. ACRYSOL™ RM-1600 Newtonian HEUR ICI builder improves film build and smoothness. Also improving film build, ACRYSOL™ RM-3030 promotes flow/leveling and allows reduced thickener use, without compromising stability, and higher ICI efficiency with minimal KU contribution. Read More

Materials & Material Processing

Rheology Modifier replaces cellulosic paint thickeners.

April 15, 2016

As partial or complete replacement for hydroxyethylcellulose technology, ACRYSOL™ DR-180 HASE Rheology Modifier offers optimal dry pound efficiency and is compatible across wide range of binder technologies and formulation spaces. Product provides in-can stability and surface smoothness without impacting other paint properties. With additive, paint can be transformed to meet contractor demands for optimized coverage and seamless touch-up with support for spray, brush, and roller application. Read More

Architectural and Civil Engineering Products, Cleaning Products & Equipment, Materials & Material Processing, Green & Clean

Natural Quartz Material offers expanded color options.

April 14, 2016

Moldable into round and curved shapes, Evero® Natural Quartz Surface line adds dimension to commercial washroom design. Product comes in 22 colors, including shades of whites and grays, as well as earthy beige and taupe tones. Expanded color options have been added to Evero Geo Series, which is made from blend of bio-based resin, natural quartz, granite, recycled glass, and other exotic minerals, and has 25% recycled content. Non-porous surface is chemical, stain, impact, and scratch resistant. Read More

HVAC, Materials & Material Processing

BITZER Approves HFO Refrigerants for Screw Compressors

April 13, 2016

BITZER approves HFO refrigerants for screw compressors

  • Extensive qualification program completed
  • Alternative for R134a refrigerant
  • Screw compressors boast high efficiency
Following an extensive qualification program, compressor specialist BITZER has announced approval of the R1234yf and R1234ze(E) HFO refrigerants for its CSH and CSW screw... Read More

Chemical Processing & Waste Management, Materials & Material Processing

Versum Materials(TM) Makes Debut; will Showcase Broad Range of Additives that Enable High-Performance Coatings at 2016 American Coatings Show

April 13, 2016

Expo Will Mark First Appearance of New Brand for Air Products' Materials Technologies Business LEHIGH VALLEY, Pa. - Attendees looking for the distinctive green Air Products (NYSE: APD) logo at the 2016 American Coatings Show (ACS), April 11-14, Indianapolis, Ind., will instead find the company's market-leading portfolio of epoxy curatives, resins and diluents, and additives for... Read More

Materials & Material Processing, Paints & Coatings

Waterborne Binder adheres to steel and metallic surfaces.

April 13, 2016

Designed for use in intumescent coatings that protect structural and architectural steel, ProHere™ V 30290 exhibits optimized compact and stable foaming properties. Polymeric binder minimizes demand for coalescing agent in formulation, resulting in lower VOC coating. Product can be formulated into coatings that meet fire resistance classifications of up to 90 minutes. With long open time and ease of workability, ProHere™ V 30290 is suitable for factory or on-site application. Read More

Fluid & Gas Flow Equipment, Materials & Material Processing

Nickel Chromium Alloy comes in corrosion-resistant grades.

April 12, 2016

Meeting needs of those installing equipment in harsh environments, Sanicro™ 60 (Alloy 625) is available in seamless pipe as well as hydraulic and instrumentation (H&I) and heat exchanger tubes. Austenitic nickel-chromium alloy, which is resistant to pitting and intergranular corrosion, is also virtually immune to stress corrosion cracking in environments containing chloride. Operating range from -321 to +1,500°F, OD range from 0.25–1.625 in., and wall thickness vary from 0.035–0.197 in. Read More

Materials & Material Processing, Waste Handling Equipment

Nucleating Agents and Clarifiers cut molding cycles.

April 11, 2016

Intended for processors of PP and HDPE, +Speed™ Additives are effective at minimal use levels. Letdown ratios range from 0.1–0.5% for 3 grades of nucleating agent and 0.2–1.0% for fourth grade that serves as nucleating and clarifying agent. All products comply with California Proposition 65 and are FDA approved for food-contact applications. Offered in pails or drums, products come in custom blends with liquid colors, or as one of GlobalPlus™ range of liquid additives. Read More

Chemical Processing & Waste Management, HVAC, Materials & Material Processing, Green & Clean

Maintech Resources Completes RTO Installation

April 8, 2016

Maintech Resources recently completed the installation of a RTO in the Los Angeles area for a manufacturing facility to meet the SCAQMD (South Coast Air Quality Management District) Regulations. This Green project used state of the art air pollution control technology in order to treat the exhaust gas from a manufacturing facility, including hazardous air pollutants and volatile organic... Read More

Chemical Processing & Waste Management, Materials & Material Processing, Paints & Coatings, Green & Clean

Dow Expands Boundaries with Customers at 2016 American Coatings SHOW

April 6, 2016

Industry experts from Dow showcase new rheology modifiers and other innovations developed to solve industry challenges PHILADELPHIA – The Dow Chemical Company (NYSE: DOW) is answering the dynamic needs of coatings formulators, manufacturers, regulators and applicators with the latest innovations to help solve their most critical challenges at the 2016 American Coatings SHOW April 12-14,... Read More

Computer Hardware & Peripherals, Material Handling & Storage, Materials & Material Processing

Griplock® Systems to Showcase Latest Innovations in Cable Suspension at LIGHTFAIR® International 2016

April 5, 2016

Griplock® Systems will be attending LIGHTFAIR® International April 26-28, 2016 in San Diego booth #2849. Carpinteria, CA – Griplock Systems will be attending LIGHTFAIR® International April 26-28, 2016 in San Diego booth #2849. On display will be Griplock® Systems’ latest innovations including Wisp™, Rincon™, and Solimar™. Wisp™ is a thin and small, yet incredibly strong,... Read More

Chemical Processing & Waste Management, Materials & Material Processing

Gas Injector accelerates water deaeration.

April 4, 2016

With Dif-Jet Gas Injector, nitrogen gas is injected and mixed into pressurized water pipe and then discharged into and circulated in tank of water. Nitrogen, being highly soluble in water, will force oxygen out of water without requiring vacuum pump, heat, or other device. Oxygen is vented out of top of tank automatically. When fed 5 cfm of nitrogen at 25 psi, injector produces 500 gallons of de-aerated water in 25 minutes. Treated water has dissolved oxygen content of less than .1 mg/L. Read More

Materials & Material Processing

Calix Ceramic Solutions Now Offering Boron Carbide Composite Materials

March 28, 2016

Calix Ceramic Solutions is now offering a Boron Carbide Composite Material ideal for severe wear and abrasive applications. The material is a composite of boron carbide and silicon carbide which leads to an increase in strength and hardness as compared to other composite materials. This composite material's high hardness and fine grain size makes the material ideal for components subjected... Read More

Machinery & Machining Tools, Materials & Material Processing

High-Performance Solid Carbide Tool is suited for dynamic milling.

March 22, 2016

Designed for optimum performance on steel with secondary applications in stainless steel, Proto&bull;max&trade; ST Z-5 features 5 cutting edges and is available with wear-resistant TAZ coating. Design reduces risk of tool breakage and is available with Weldon shank configuration for secure clamping, with or without corner radius, and without reduced neck for greater stability by using maximum amount of carbide. Offered in 6&ndash;25 mm dia, this milling tool also has helix angle of 35°.<br /> Read More

Materials & Material Processing

Chromaflo Presenting Leading Technologies at UTECH 2016

March 16, 2016

Ashtabula, Ohio, U.S.A. – Chromaflo Technologies, a leading independent global supplier of pigment and chemical dispersions for the thermoset and coatings industries, will present a broad portfolio for the urethane market at Utech North America,  April 6 and 7, 2016. Plasticolors® DTP Line – Markets first DOTP line with a colorant file system Plasticolors® DTP colorants consist of... Read More