Bulk Materials

Mining, Oil Drilling & Refining, Materials & Material Processing

Resin-Coated Proppant increases production of oil and gas wells.

October 6, 2015

With optimized conductivity and strength, InnoProp® Python RCS (Resin Coated Sand) prevents proppant flowback to well-bore. Use of U.S. Silica White® sand promotes quality and consistency, and product does not sacrifice quality for performance. Available in all mesh sizes utilized in frac designs, this proppant is recommended in all formations with net closure stresses up to 10,000 psi. Read More

Architectural and Civil Engineering Products, Materials & Material Processing, Green & Clean

Composite Sheathing helps lower energy bills.

May 15, 2015

Made with 100% composite materials and manufactured without adhesives, Composite Structural Insulated Sheathing optimizes building strength and air quality while earning LEED points and NAHB green certification. Fiberglass reinforced thermoset skin is impervious to moisture and is bonded by chemical reaction to polyurethane foam insulation during manufacturing, eliminating delamination. Continuous polyurethane foam adds R-6 insulation in 1 1/8 in. sheathing and R-12 in 2 1/8 in. sheathing. Read More

Materials & Material Processing

Composite Materials create functional prototypes.

December 2, 2014

Available for ProJet® 5500X composite 3D printer, VisiJet® Functional Elastomers give users versatility to create models, functional prototypes, and end-use parts with multiple material printing. Flexible materials, available in black and translucent, offer Shore A value starting at 30 and rise in increments of 10. Combining materials with VisiJet ABS-like white or VisiJet polycarbonate-like clear materials, ProJet 5500X can create up to 14 unique materials in single print. Read More

Chemical Processing & Waste Management, Printing & Duplicating Equipment, Materials & Material Processing

Electrically Conductive Silicone targets printed electronics.

November 20, 2014

Designed with less than .003 Ω/cm resistance, EXP-06335 is printable via screen, flexo, or slot die. Heat cure, one part material is packaged in any size container and has stable shelf life of 6 months at room temperature. Flexible and electrically conductive, product adheres to most common circuit board materials, PU, silicone, and metal substrates. It does not require use of primers, buffers, conformal coatings, or silicone gels. Read More

Mechanical Components & Assemblies, Materials & Material Processing

Composite Pellet acts as drop-in die-cast magnesium substitute.

September 8, 2014

Complét® LFT duplicates mechanical and electrical properties of magnesium in injection molding or extrusion materials that offer up to 40% reductions in weight. Matching mechanical performance of pressure die-cast magnesium and aluminum with tensile modulus up to 42,000 MPa, pellets offer surface resistivity down to 0.2 Ω/sq and EMI shielding capabilities from 60–80 dB. Combination of mechanical and electrical properties provided in these composites is achievable in range of polymers. Read More

Materials & Material Processing

Carbon Fiber Molding Compound offers weight, performance benefits.

April 25, 2013

Designed to replace steel, aluminum, and range of traditional composites in high-volume automotive applications, AMC-8590-50 Carbon Reinforced Advanced Molding Compound (AMC®) helps develop lighter weight structural and semi-structural solutions. Compound utilizes high tow 50K carbon fiber reinforcement and is available in 12, 25, or 50 mm chopped lengths as well as continuous fibers (unidirectional and woven). Various resin matrices are available. Read More

Materials & Material Processing, Architectural and Civil Engineering Products

Colored Quartz Aggregate Flooring supports traffic in 2 days.

January 28, 2013

Available in 16 standard aggregate colors and blended patterns as well as custom blends, Color-Rok Flooring can be broadcasted into 100% solids epoxy or methyl methacrylate coating. Pure silica quartz aggregate is UV stable and chemical resistant and can be formulated with antimicrobial additive. Able to be applied to smooth or textured finish, durable and seamless floor is unaffected by acids, detergent solutions, animal fats, vegetable oil, gasoline, petroleum oil, blood, and urine. Read More

Materials & Material Processing

Two-Part Polyurethane accelerates concrete repair.

January 15, 2013

With cure time under 20 min, Crackbond CSR exhibits strength of 4,900 psi in 1 hr. Viscosity allows deep penetration into concrete cracks, enabling high-strength structural repair. Self-leveling material, which may be used down to 0°F, consists of resin and hardener uniformly dispensed from dual cartridge system and mixed simultaneously through mixing nozzle. Uses include repairing spalled floor joints and concrete on bridge and parking decks as well as repairing floors.
Read More

Materials & Material Processing, Construction Equipment & Supplies

Concrete Repair System simplifies crack injection process.

October 11, 2012

Crack-Kit provides everything needed to complete application that requires crack injection: Crackbond LR-321 Injection Resin, Miracle bond Capping Paste, plastic putty knife, nozzles, flow restrictors, tongue depressors, latex gloves, and mixing cups. While 12 flexible T-Ports (included) feature latex storage pod that delivers constant injection pressure and indicates if more injection is required, Observation Windows help users view and confirm flow of resin within injected crack. Read More

Labels, Tags, Signage & Equipment, Paints & Coatings, Materials & Material Processing, Construction Equipment & Supplies, Architectural and Civil Engineering Products

Concrete Overlay covers up unsightly floors.

June 4, 2012

Designed to gain strength rapidly, DuraFloor non-component, flowable overlay allows vehicle traffic or mechanical polishing within 24 hours after placement. Positive bonding ensures precise mortar repairs on worn and pitted concrete surfaces. Suitable for both interior and exterior use, cement-based polymer-reinforced material may be placed in various thicknesses from ¼-5 in. deep. Read More

Chemical Processing & Waste Management, Materials & Material Processing

Thermoset Structural Composites resist moisture and chemicals.

July 29, 2011

Consisting of single and hybrid chemistries using polyester, vinyl ester, polyurethane, and epoxy resins, Engineered Structural Composites experience little or no degradation in extreme hot and cold temperatures, making them suited for most demanding industrial and outdoor environments. Products maintain rigidity, resist corrosion, and can be molded using variety of standard processes and tools. Composites are available as both Sheet Molding Compounds and Bulk Molding Compounds. Read More

Mechanical Power Transmission, Green & Clean, Materials & Material Processing

Fiber-Reinforced Composite enhances wind turbine blade design.

May 11, 2011

Available in 12-78 mm thicknesses, TYCOR® W5 fiber-reinforced composite core material meets design requirements of longer, heavier utility wind turbine blades. It is suited to vacuum infusion and provides 105 MPa min transverse shear modulus in all directions. Offering alternative to balsa with consistent infused density, minimal resin absorption, and optimal dimensional stability, material achieves balanced transverse shear stiffness suited for thin, highly-loaded shear webs and shells. Read More

Materials & Material Processing

Miniature Cooling Aggregates have clip fastening feature.

September 14, 2010

Demand for power transistors to be installed with minimal effort is met by use of cooling aggregates featuring engaging retaining springs for fastening transistors and similar devices. Groove geometry allows safe fastening of transistors on cooling aggregates assembly without screws. There are 5 different clip sizes available for differently sized components, and 3 different voltages of cooling aggregates - 5, 12, and 24 Vdc - accommodate range of applications. Read More

Materials & Material Processing

HPL Dielectric Material delivers superior heat transfer.

July 19, 2010

At 0.0015 in. thin, Thermal Clad® HPL (High Power Lighting) dielectric is formulated for high-power lighting LED applications with demanding thermal performance requirements. It withstands high temperatures with glass transition of 185°C and thermal performance of 0.30°C/W (RD 2018). Substrates minimize thermal impedance and efficiently conduct heat. Use results in lower operating temperatures, which subsequently extends LED lifetimes and durability in HPL applications. Read More

Paints & Coatings, Materials & Material Processing

Dielectric Precursors help deposit films on memory chips.

June 17, 2010

EXTREMA® STO precursors, which are strontium titanium oxide compounds with high dielectric constant, help deposit ultra-high k dielectric films using atomic layer deposition (ALD) in 22-15 nm DRAM devices. Germanium, antimony, and tellurium alloy EXTREMA® GST precursors allow thermal ALD of conformal films for manufacturing PRAM devices at 22 nm and below and are suitable for solid state memory. Both products enable compositional control of new semiconductor films. Read More

Green & Clean, Materials & Material Processing, Construction Equipment & Supplies, Architectural and Civil Engineering Products

Composite Landscape Pavers are available in 4 x 8 in. size.

March 1, 2010

VAST Composite Landscape Pavers, manufactured of up to 95% recycled car tires and plastic containers, are suited for large commercial hardscapes such as parking areas, walkways, building entrances, and plazas. Weighing less than 9 lb/sq ft, they provide high slip resistance and strength. Products include installation grid, with same composite material, that are laid out on compacted sand base on which pavers are automatically spaced and aligned. Read More

Test & Measuring Instruments, Materials & Material Processing

Prototyping Material simulates parts made out of rubber.

October 8, 2009

With TangoBlackPlus, designers and manufacturers can create parts that closely resemble broad range of rubber products. Material offers flexibility, optimal elongation and break, and resistance to tear. Black in color, product is suited for creating models of products in automotive market, defense industry, and shoe industry. It will also help development of soft-touch grips, handles, gaskets, and seals. Read More

Chemical Processing & Waste Management, Materials & Material Processing, Architectural and Civil Engineering Products

Composite Cement is lightweight and flexible.

October 5, 2009

Xtreme Lightweight Series is blend of cement with lightweight aggregates and reinforcing fibers. Fireproof, termite-proof, and mold-resistant, it can be cut, trimmed, nailed, molded, and formed into any shape. Product also allows any finish or any texture of wood or stone to be simulated; it attaches to gypsum, wall board, and concrete block, wood, and metal and can be stained, painted, or colorized throughout mix. Read More

Materials & Material Processing, Construction Equipment & Supplies

Concrete Floor Patch Kit cures in as little as 1 hr.

October 1, 2009

HyperPatch(TM) lets end-users apply heavy-duty repair patch, indoors or outdoors, that will be ready to walk on within 1 hr. It comes in 2 gal container, which includes urethane liquids, trowel-grade sand, and complete instructions. Once mixed, material can be hand-troweled at recommended ¼ in. thickness. Areas of use include hallways, food service areas, laboratories, showers areas, food processing, hospitals, manufacturing plants, sidewalks, and dock areas. Read More

Paints & Coatings, Materials & Material Processing

Gel Paste offers thermal conductivity up to 6.5 W/moK.

June 19, 2009

Supplied in syringe to facilitate application, V30Z63MDP Series features specific volume resistance ratio up to 7.2 x 1014 Wocm, dissipation factor down to 0.0004 at 1 MHz, and breakdown voltage up to 9.6 kV/mm. RoHS-controlled substance is used to fill gaps around heat sources such as semiconductors. Other applications involve surface, underside, and lead heat sources such as ICs, as well as computer internal components, power supplies, and power transistors. Read More