Shin-Etsu Microsi, Inc.
Phoenix, AZ 85044
Aug 05, 2009 SINR series siloxane-based negative photoresist film, available in 12-100 micron thicknesses, will flow into vias to produce void-free dielectric fill and planarized surface. Suited for 3D Through-Silicon Vias (TSVs) and 2D wafer bonding applications, vacuum laminated dry films exhibit minimal residual stress with 90 MPa modulus that produces rubbery consistency and minimizes wafer bow. Dielectric constant is as low as 2.6, and built-in adhesion promoters ensure optimal bonding.

Lanxess - Technical Rubber Products
Pittsburgh, PA 15275
Jul 30, 2009 Primal(TM) SB-110 and SB-155 waterborne polyacrylate dispersions can be used as sole binder in base coats or combined with select acrylic/polyurethane dispersions to obtain balanced property profile. Used to produce base coats for very soft leathers, Primal SB-110 is optimized for embossing properties, fastness to heat yellowing, cut-through resistance, and low surface tack. Primal SB-155 shares these properties but is suitable for high-covering base coats for embossed leather types.

Pacor Inc.
Cinnaminson, NJ 08077
Jul 27, 2009 Available for high temperature and cryogenic environments, UltraGard(TM) Precut Aerogel Insulation is hydrophobic and can be used effectively in tight access areas. Aerogels consist of lightweight silica solids derived from gel in which liquid component has been replaced with gas, and reinforced with nonwoven, glass fiber batting. Environmentally safe insulation is available in 5 and 10 mm thicknesses, nominal length of 59½ in., and widths of 1½, 2, and 3 in.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jul 17, 2009 Capable of providing tensile shear strength of 2,400 psi and flexural strength of 13,400 psi, Aremco-Bond(TM) 2200 bonds ceramic and metal wear plates. Electrical insulating properties include dielectric strength of 460 V/mil and volume resistivity of 1.0 x 1015. Abrasion, corrosion and impact resistant compound cures at room temperature in 24-48 hr or by heating to 175 °F for 4 hr. Cured product is machinable and features linear shrinkage of .009 in/in and Shore-D hardness of 86.

Bayer MaterialScience LLC - Polyurethanes
Pittsburgh, PA 15205
Jul 15, 2009 Bayhydrol AH XP 2741 high-molecular-weight, polyacrylate dispersion is solvent-free and is suited for formulation of low- to no-VOC, 1-component coatings for indoor wood floors and furniture. Clearcoats formulated with styrene-acrylate copolymer resin accentuate wood grain and provide chemical resistance. Resin can be used to formulate primers, high-gloss or semi-gloss coatings, and in combination with polyurethane dispersions and UV-cured coatings.

Americhem, Inc.
Cuyahoga Falls, OH 44222
Jul 09, 2009 Completely customizable, nDuramax(TM) family includes UV stabilizer solution for PET fibers used in outdoor PET applications, such as awnings, boat covers, and geosynthetics, which are constantly exposed to elements and require fibers with optimal weathering performance. Line also includes product for packaging industry, offering extended shelf life and preservation of product contents. Stabilizers additionally protect against color fade and maintain bottle clarity.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jul 08, 2009 Supplied in powder form and mixed with water, Ceramacast(TM) 575N fine-grain, alumina-filled, ceramic compound is suited for potting high-temperature electrical components including lamps, heaters, rheostats, and temperature sensors. Product offers temperature resistance to 3,000°F, dielectric strength of 150 V/mil, compressive strength of 11,800 psi, and moisture and chemical resistance. Compound hydraulically sets in 16 hr at room temperature and cures fully at 250°F in 1-2 hr.

Emco Industrial Plastics, Inc.
Cedar Grove, NJ 07009
Jul 07, 2009 With Microban antimicrobial protection built in during manufacturing process, Lucite L Cast Acrylic Sheet inhibits growth of microbes such as bacteria, mold, and mildew that can cause stains, odors, and deterioration of product. Available in full sheets, cut to size pieces, or fabricated parts, Lucite L comes in thicknesses from 1/8-¼ in. It is suited for medical and foodservice industries where bacteria causes health concern.

Trelleborg Sealing Solutions
Fort Wayne, IN 46801
Jul 07, 2009 Developed for oil and gas applications, XploR(TM) range of explosive decompression resistant materials includes compounds in HNBR, FKM, and Isolast® Perfluoroelastomer (FFKM), each of which demonstrates explosive decompression resistance. Materials in XploR(TM) range satisfy NORSOK M-710 sour service and Rapid Gas Decompression test conditions. They are available in standard international o-ring sizes and cross sections, along with custom-engineered solutions and seal designed profiles.

Henkel Loctite Corporation
Rocky Hill, CT 06067
Jul 01, 2009 Comprised of 7 products, Loctite® Light Cure Silicones offer cure depths up to 2 in. and cure fully in seconds when exposed to high-powered UV or visible light. Solvent-free adhesives/sealants deliver elastic seal with optimized degradation resistance. Able to bond with silicone, plastic, and metal substrates, they exhibit weather, temperature, and moisture resistance. Uses include general bonding and sealing as well as replacing molded or die-cut gaskets and coating applications.

Henkel
Rocky Hill, CT 06067
Jun 25, 2009 Producing 15 releases per application, VOC and organic solvent free Frekote® Rel-Eaze(TM) can be applied at room temperature and cures at ambient temperatures within 30 sec. Low viscosity liquid can be sprayed on as thin coating using high-volume, low-pressure spray systems or wiped on with cotton cloth. When touch up is required, molding can continue immediately after touchup coat is applied. Product is available in 1 gal cans, 5 gal containers, and 55 gal drums.

Americhem, Inc.
Cuyahoga Falls, OH 44222
Jun 23, 2009 Acting as cooling agent, xCelmax(TM) increases crystallization temperature of polymers, and minimizes potential for defects and end product warping without typical process changes. Product is available in multiple pellet and bead sizes and can be incorporated into color and additive masterbatches without additional equipment. It is also suitable for use with polyolefin masterbatches that produce PP bins, HDPE bottles, PP closures, and PP thermoformed containers.

SolarBee, Inc.
Dickinson, ND 58601
Jun 23, 2009 SolarBee® Chlorine Boost System boosts water quality in water storage tanks, helping achieve compliance with EPA Stage 2 disinfection byproduct rules. Designed for use with SolarBee water mixing equipment, portable system boosts chlorinated/chloraminated water tanks with sodium hypochlorite. It includes 20 gal sodium hypochlorite holding tank, 5 gal rinse tank, and 3/8 in. teflon chemical hose as well as double-diaphragm pump to inject compound into tank and flush injection hose.

Advanced Anti-Vibration Components - AAC
New Hyde Park, NY 11040
Jun 19, 2009 Supplied in syringe to facilitate application, V30Z63MDP Series features specific volume resistance ratio up to 7.2 x 1014 Wocm, dissipation factor down to 0.0004 at 1 MHz, and breakdown voltage up to 9.6 kV/mm. RoHS-controlled substance is used to fill gaps around heat sources such as semiconductors. Other applications involve surface, underside, and lead heat sources such as ICs, as well as computer internal components, power supplies, and power transistors.

Bayer MaterialScience, LLC - Coatings, Adhesives & Sealants
Pittsburgh, PA 15205
Jun 18, 2009 Suited for use in medical devices, hydrophilic coatings are intended to combine lubricity and hemocompatibility with mechanical properties of polyurethane. Formulation exhibits minimal swelling and is optimized for strength/durability. Aqueous polyurethane dispersions are of solvent-free nature with low viscosity, while solvent-borne polyurethane solutions are characterized by stability and wet strength.

Meadows, W.R., Inc.
Hampshire, IL 60140 0338
Jun 15, 2009 Supplied as colorless liquid, LIQUI-HARD ULTRA penetrates into concrete surface, where chemical reaction takes place that produces byproduct that fills in pores of concrete at molecular level. Finished surface offers abrasion and chemical resistance and is more durable than that of untreated concrete. LIQUI-HARD ULTRA is environmentally safe, water-based product and features zero VOC content.

Dontech, Inc.
Doylestown, PA 18901
Jun 11, 2009 IMO-bond(TM), optical coupling of contrast enhancing cover glass to front polarizer of display, eliminates reflections from rear surface of optical filter and front surface of display system. Process of applying rigid optical filters to electronic displays via refractive index matched optical (IMO) bonding process includes index-matched adhesives that optically couple cover glass or touch screens to display to eliminate reflection and enhances sunlight readability by greater than 90%.

Epoxies Etc.
Cranston, RI 02921-3407
Jun 10, 2009 Formulated for electronic potting and encapsulating applications, Type 20-3060 Epoxy flows quickly in and around electronic components, self levels, releases air bubbles, and provides smooth, glasslike finish. It offers electrical insulation, chemical resistance, and protection from environment. Potting compound is available in quarts, gallons, and 5 gal pails.

NuSil Technology
Carpinteria, CA 93013
Jun 10, 2009 Available with refractive index of 1.54 and viscosities from 3,500-8,000 cP, LS-3354, LS2-3354, and LS3-3354 are designed for potting, encapsulating, backfilling, and dampening applications requiring soft gel with optical clarity. Cure can be achieved at ambient temperatures with humidity or accelerated with heat, and gels can be removed for rework if needed. Available in 1:1 mix ratio, products are suited for protecting electronic components from dust, debris, and moisture.

Americhem, Inc.
Cuyahoga Falls, OH 44222
Jun 08, 2009 For optimized physical properties and cycle times, nCore(TM) chemical blowing agents exhibit characteristics such as heat and sound insulation, sink mark prevention, and nail and screw acceptance without specialized installation equipment. Products suit injection molding, extrusion, and calendaring operations and can be formulated to fit resin, compound, and/or manufacturing processes. Options for exothermic, endothermic, or blended products are available.