IRC, Advanced Film Div.    Corpus Christi, TX 78411
Dec 15, 2005 Providing thermal conductivity to polymer-based insulated metal substrates, Anotherm(TM) is insulated by chemically grown, anodized dielectric layer with solderable screen printed conductors. It eliminates need for additional heatsinks and features uniform thickness of 35 microns, with no potential for delamination or peeling. Max operating voltage is 250 Vac, with thermal impedance at 0.2°C/W, and max continuous operating temperature is 400°C without solder mask.

Dow Corning Corp.    Midland, MI 48686 0994
Dec 15, 2005 Able to squeeze down during application for increased contact surface, InstantGlaze® II facilitates application and installation of glass for residential and small commercial window and door manufacturers. Soft texture promotes elasticity and elastic recovery performance. Product features 24 hr pot life and up to 15 min of open time, develops instant green strength, and bonds to vinyl, wood, glass, aluminum, paint, and fiberglass.

Kinetic Instruments, Inc.    Bethel, CT 06801
Dec 13, 2005 Suited for bench top and automated UV curing applications, SpotCure-B6 is available with 2 interchangeable light probes to cure UV adhesives in 365 and 395 nm ranges. In automatic operation mode, light activates ON when probe is removed from holder, and OFF when replaced in holder. Light delay of 1.5 sec allows accurate positioning of 12 mm light probe over work area, while selectable 10 sec timed cycles up to 60 sec and manual mode allow accurate control of curing time.

Premix Thermoplastics, Inc.    Milton, WI 53563
Dec 12, 2005 With conductivity less than 1 x 10⁵, PRE-ELEC 12-000 conductive compounds are based on copolymer polyacetal with carbon black or carbon fiber additive, while PRE-ELEC 12-031 compounds can be colored without affecting electrical properties. Ranging from 1 x 10⁹ to 1 x 10¹¹ §Ã™, PRE-ELEC ESD 12-000 static dissipative compounds are colorable alloys of copolymer polyacetal and inherently dissipative polymers.

TPE Solutions, Inc    Shirley, MA 01464
Dec 08, 2005 Featuring 20 to 90 Shore A hardness range, Softlink 900 Series TPEs allow lowering of friction coefficient to improve abrasion resistance. Off-white or easy-to-color compounds can be processed without preheating or drying and offer matte finish. Used in 2-shot molding, compounds can substitute for silicone, latex, or rubber in power tools, hand tools, appliances, and consumer products.

Speedline Technologies Inc.    Franklin, MA 02038
Dec 08, 2005 With max temperature of 662°F, lead (Pb)-free OmniFlex(TM) 10 Reflow Oven features variable-speed, closed-loop blower control; power limiting, balanced gas flow; and dual-chamber heating design. Process width is 20 in., heated length is 148 in., and and cooling length is 50.5 in. Lead (Pb)-free Electrovert VectraElite(TM), combined with UltraFill nozzles and upper High Velocity Convection pre-heat module, incorporates ServoJet spray fluxer and roll-out solder pot design.

JRI Industries, LLC    Springfield, MO 65803
Dec 07, 2005 With automatic operation, closed-loop, countertop Model JR-1 cleans using only hot water and biodegradable detergents. It includes motor-driven rotating basket and multiple spray bars on top, bottom, and side, all equipped with V-Jet nozzles. Washer operates on 110 or 220 V and is suited for various applications including automotive and industrial. Oil removal system, low water shut-off, oil absorbent pads, and portable cart are optional.

Quadro Engineering Corp.    Waterloo N2V1A1  Canada
Dec 07, 2005 Available in 4 sanitary and industrial designed models offering liquid throughputs from 3 gpm, ZC5 is engineered to incorporate and disperse powders into liquid stream in single-pass. Rotor/stator design enables shearing of powders prior to hydration, producing homogeneous dispersions free of lumps and fish-eyes. Vacuum permits concentrations up to 25% by weight to be generated with minimal air entrainment. Design eliminates over-processing and wastages.

Mearthane Products Corp.    Cranston, RI 02921
Dec 06, 2005 Formulated to have constant high coefficient of friction to promote uniform feeding, self-cleaning Pick Pads are made from Durethane F/C, a chemically blown or mechanically mixed/frothed cellular foam with closed cell structure. Pads provide volume resistivity from E8-E10 ohm-cm at hardness of 10-95 Shore A. Pick pads are used in paper feed and advance systems to move paper, plastic film, and other thin film substrates from trays and transfer them to rollers.

Binks ITW Industrial Finishing    Glendale Heights, IL 60139
Dec 06, 2005 Available in 3 model options to suit non-agitated, rotary agitated, and oscillating agitated applications, 2-quart SG-2 Plus(TM) delivers continuous mixing capabilities. Four-screw lid design facilitates hose attachment, while divorced design of regulator and handle aids in maintenance. Dual-regulation is provided for rotary agitation models, and all models incorporate check valve that prevents paint clogs in internal spring.

Xenon Corp.    Woburn, MA 01801 1057
Dec 02, 2005 Designed for integration into in-line manufacturing process, Xenon CoolCureXL RC-800 Series Curing System features high-intensity, pulsed UV lamps with single- or dual-lamp operation, controller that provides instant on/off, and power supply. Modular system permits top-down and bottom-up curing configurations. Suitable for chemistries that absorb light at 180-1,000 nm, UV process does not create or use VOCs and produces peak pulses less than 300 µs, 1,000 W/cm².

C-Tech Industries    Camas, WA 98607
Dec 02, 2005 Using pressurized hot water and industrial detergents with rust inhibitors, top-load, automatic Cuda 2518 is large enough to clean transmission bells. It features 18 in. high wash cabinet, 25 in. diameter rotating turntable, and 500 lb capacity. Rated at 3 hp, seal-less pump delivers cleaning power at 50 gpm and 45 psi. Removable 10-mesh debris screen prevents loose parts and heavy particles from entering wash solution and damaging pump or clogging plumbing.

Tecan    Rancho Santa Margarita, CA 92688
Dec 01, 2005 Manufactured using Photo ElectroForming and photo-etching techniques, nickel and stainless steel masks combine coplanar rigidity with burr-free aperture edges. Multi-level masks with stepped recesses can also be produced, limiting need for spacer sheets in multiple-sheet sets. Cross-section thickness, where apertures occur, minimizes photo-shadow. Masks are suited for use across various selective vacuum chamber processes.

BP Lubricants USA, Inc.    Wayne, NJ 07470
Dec 01, 2005 Blended with partial synthetic base stock, Castrol® Hypuron(TM) S protects engines while optimizing component and equipment life, allowing fleets to extend service intervals. In addition to providing dispersancy to manage high soot levels generated by EGR engines, product offers detergency to neutralize high acid levels. Oil is formulated with low ash technology, minimizing oil consumption and piston deposit formation.

Select-Arc, Inc.    Fort Loramie, OH 45845-0259
Nov 30, 2005 Part of nickel-iron alloy group, self-shielded SelectWear 55NI is intended for buildup, joining, and repair of cast iron components as well as welding of cast iron to dissimilar metals. With hardness maintained to 1,200°F, SelectWear NICRB60-G nickel-chromium-boron electrode offers corrosion and abrasion resistance. Tubular SelectWear NIWC uses low melting temperature alloyed nickel sheath filled with tungsten carbide to weld dredge and rock drilling components.

Distech Systems, Inc.    Rochester, NY 14606
Nov 29, 2005 Compatible with most machine tools, Model DS1200-MTL uses robotic technology to load and unload parts. It accepts stacks of trays from carts, eliminating operator lifting. From position next to machine tool, robotic arm feeds parts directly into chuck, spindle, fixture, or machine tool's internal loader. Model DS1200-MTL is also capable of performing secondary operations such as part washing, packout, and stacking.

Ampacet Corp.    Tarrytown, NY 10591-5130
Nov 29, 2005 Ampacet 102794 allows polyethylene-based packaging films to be adhesive laminated to those made of polyethylene terephthalate or other polymer with little or no change in coefficient of friction after lamination. Product helps keep film movement through form, fill, and seal machine predictable and problem-free. There is no need to overdose it to compensate for lubricant migration from sealant layer after lamination.

Ferrari Textiles Corp.    Pompano Beach, FL 33069
Nov 29, 2005 Suited for new buildings, renovations, or building extensions, Stamisol FT 371 is rated with M1, B1, and Euroclass Bs2d0 fire classifications and withstands temperatures from -22 to 158°F. Controlled biaxial weaving performed on polyester scrim during coating process ensures dimensional stability in warp and weft directions. Custom-fitted to specific structure, composite textile acts as insulating barrier in cold weather and provides protection from sun in warmer months.

GE Advanced Materials    Wilton, CT 06897
Nov 29, 2005 One-component Tufel I is suited for tubing applications such as catheters and IV lines, while 2-component Tufel III provides resilience and elastic memory in tubing for peristaltic pumps. Both platinum-cure, silicone elastomers are cured without peroxides that can product VOCs, and are compositionally compliant with FDA 21 CFR 177.2600 for indirect food contact. They can be sterilized using steam, gamma radiation, and EtO.

General Kinematics    Crystal Lake, IL 60014
Nov 28, 2005 VIBRA-DRUM® sand and casting processors are suited for high-volume mold/sand handling in foundry applications. In one continuous operation, this 2-mass system removes sand and tramp metal without damaging castings, reduces sand lumps to original grain size, and equalizes shakeout sand temperature. Non-rotating design features natural frequency vibration, high-frequency agitation, and 2-mass vibrating drums that deliver capacities to 400 TPH.