Cobar Solder Products    Londonderry, NH 03053
Jan 20, 2006 Suited for lead (Pb)-free wave soldering applications, Cobar 396-FTA eliminates solder balls as well as wetting and wicking issues, even on OSP assemblies. Product has less than 2% solids, yielding clean post solder surfaces. It is suited for use on most types of circuit boards.

Newson Gale, Inc.    Lakewood, NJ 08701
Jan 20, 2006 With flashing green LED, intrinsically safe Bond-Rite Remote wall-mounted monitoring module and grounding clamp system continually verifies low-resistance connection to ground is maintained in areas where potentially flammable materials exist. Models may be battery powered or line powered through power supply unit mounted in safe area up to 350 ft away. Approved for use in hazardous locations, monitoring electronics are housed in corrosion-resistant stainless steel enclosure.

Xuron Corp.    Saco, ME 04072 1840
Jan 19, 2006 Hand-held Wickgun(TM) lets users dispense, position, and cut-off braid using one hand while holding solder iron in other hand. Featuring braid with no clean flux, dispenser eliminates handling of braid and minimizes waste. Available in 4 braid sizes from 0.035-0.110 in. wide, cassettes are preloaded with 15 ft of braid. Dispenser allows braid to be advanced and retracted using thumbwheel and then cut-off by squeezing trigger.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jan 19, 2006 Aremcolox(TM) 502-600 is used to produce thermally insulative and high dielectric components and fixtures used in electrical and electronics applications to 1,100°F. Along with zero porosity, product exhibits compressive strength of 32,000 psi and flexural strength of 14,000 psi. Product, available in rods from ¼-1 in. dia x 18 in. long and plates from 14 x 20 x 1/8-1 in., offers 380 V/mil dielectric strength and 4.08 Btu-in/hr-ft²-°F thermal conductivity.

Epoxies Etc.    Cranston, RI 02921-3407
Jan 19, 2006 One-component 60-7105 adhesive, coating, and potting compound cures within seconds when exposed to UV light. With viscosity of 3,000 cps, product self-levels around intricate electronic designs, can cure in deep sections, and adheres to most substrates. Adhesive is available in pre-packaged syringes, quarts, and gallons.

Hexis USA LLC    Corona, CA 92880
Jan 17, 2006 Used indoors or outdoors, self-adhesive S5DEP series is comprised of 6 shades of 3-mil polymeric vinyl that withstands up to 5 years (blue, green, yellow, pink, and sparkle shades) or 8 years (silver shade) of vertical outdoor exposure. Semi-translucent appearance makes series suited for use as viewing barrier for privacy. Applied to any glass or mirror surface, products achieve etched glass, frosted glass, or sandblast effect.

JBC Tools USA, Inc.    Cary, IL 60013
Jan 16, 2006 Able to provide vacuum for demanding manufacturing environments, MS 9005 is driven by compressed air via Venturi valve and features instant ramp. Product works with DD 5700 and DM 6700 soldering stations, allowing 2 or 4 tools to be used simultaneously. In addition to providing engineering specifications control, modular system features Hibernation mode, on-screen menu with password protection, independent temperature settings for each tool, and sleep mode.

Wilson Industries, Inc.    Pomona, CA 91768-3278
Jan 16, 2006 Featuring carbon scrim, Electro-Safe heavy-duty transparent vinyl curtain is designed to bring voltage down to zero. Fire-resistant, 12 mil curtain is suited for oxygen-rich and dust-free atmospheres. Resistant to abrasion, cleaning processes, and corrosion, anti-static curtain is also useful for areas in which danger from explosives is present. Applications include machine and instrument covers, soft-wall cleanrooms, and electronic industry safety screens.

Zhejiang Yanfeng Plastic Machinery General Factory    Pingyang,Zhejiang   China
Jan 13, 2006 Along with computer-controlled frequency conversion, FYF-SPL series flat yarn extruders adopt electric digital-simulation control technology such as speed regulation and controllable silicon direct current speed regulation. Assembly offers advanced band net change structure as well as fibrosis structure used for producing flexographic packing bags or fibrosis bag sewing thread. Stock thread heating structures include hot-blast stretching bellows and electric baking board.

Mearthane Products Corp.    Cranston, RI 02921
Jan 11, 2006 Chemically blown cellular foam, Durethane F features closed cell structure and is used for banking equipment conveyor belts to bridge gaps between rollers. Mechanically mixed, microcellular Durethane M features uniform, mostly open cell structure. Solid elastomer Durethane S provides heat dissipation and resistance to wear in paper-handling and transport applications. Materials are self-cleaning, provide precision of movement, and are customizable for conductive properties.

Key Technology, Inc.    Walla Walla, WA 99362
Jan 11, 2006 Intended for tight fitting processing and packaging distribution lines, stainless steel Impulse(TM) Compact Shakers feature solid-state controls that allow conveying pan amplitudes from 0-100%. Sizes range from 8-15.7 in. wide and from 5-6.5 ft long. All units are dust and moisture resistant with controls housed in NEMA 4X rated enclosure. With oil-free electromagnetic drives, shakers help ensure food safety and meet 3A Dairy Sanitary Standards, USDA, HACCP, and FDA requirements.

Solvent Kleene, Inc.    Peabody, MA 01960-5146
Jan 10, 2006 Designed for use in immersion tank with no heating required, D-Zolve 1012 strips hard-to-remove powder coatings and paints from intricate part shapes. Product is compatible with metals, ferrous and non- ferrous, as well as plastics. Stripping time typically ranges from 30 min or less to 2 hr. Designed to minimize health and environmental hazards, product is non-flammable, has no hazardous air pollution potential, and does not contain any carcinogenic compounds.

Key Technology, Inc.    Walla Walla, WA 99362
Jan 10, 2006 Impulse(TM) Compact series utilizes dedicated solid-state controls, allowing conveying pan amplitudes to range from 0-100% to adjust for different products or processing conditions. Offered in sizes from 5-6.5 ft long x 8-15.7 in. wide, products feature capabilities that enable precise metering and gentle product handling while minimizing maintenance requirements. Stainless steel, oil-free units can be adjusted from low stroke, high cycle mode to high stroke, low cycle mode.

Norplex Micarta    Postville, IA 52162
Jan 10, 2006 Manufactured from multiple plies of woven fiberglass, which is saturated with epoxy resin and compressed under heat and pressure, NP571HT provides mechanical strength at continuous temperatures up to 210°C. Product also provides machinability, dimensional stability, and creep resistance. In use, it maintains physical, mechanical, and electrical properties for up to 1 decade. Composite is suited for applications in power generation, oil and gas, and aerospace.

Westfall Mfg. Co.    Bristol, RI 02809-2721
Jan 06, 2006 Suitable for any fluid handling system, variable flow Model 2900 utilizes 2 in-line wafer type mixers, one fixed with 0.9 Beta ratio and one variable with 0.7 Beta ratio and that adjusts incrementally to adapt to changing flow conditions. Featuring automatic modulation to maintain 3 psi regardless of flow rate, mixer flattens head loss at max flow, while providing consistent mixing over 20:1 turndown ratio. Sizes range from 3/8-120 in. ID.

Sonobond Ultrasonics    West Chester, PA 19380
Jan 05, 2006 Suited for chemical and industrial liquid applications, Filter Collar Bonder(TM) ultrasonically attaches rigid plastic circular frames to non-woven filter bags using SureWeld 20(TM) technology. Operator loads plastic ring and filter bag onto center fixture. Start button is activated causing welding head to close on part, ultrasonically weld it, and retract. Operator then manually rotates center fixture 60° and repeats process 6 times to achieve 360° weld.

Carver, Inc.    Wabash, IN 46992 0544
Jan 05, 2006 With no hydraulics, E-Series provides clean, quiet operation suited for compression molding rubber/elastomers, gum silicones, TPRs, thermosets, and plastics, as well as bonding and laminating applications. All electric power/drive system provides ramping of clamp force from 1,000 lb to 30 tons. Standard temperature range is to 650°F, and platen sizes range from 12 x 12 in. to 24 x 24 in. Functions can be programmed with microprocessor-based control.

Bekaert Specialty Films    San Diego, CA 92123-4359
Jan 04, 2006 Spectrally selective Panorama® Hilite 70 helps meet daylighting and solar control needs of architectural properties by blocking over 99% of damaging UV radiation and 95% of uncomfortable IR heat, while not noticeably affecting visible light transmission. Optically clear, polyester-based glass coating, applied to interior glass surface, helps eliminate hotspots around windows and glass doors, balance room temperatures, and reduce energy costs.

Wellington Alloys    Franklin, MI 48025
Dec 30, 2005 Used to fabricate plates, chutes, and hoppers, WELLBRAZE and WELL-CLAD suit high- and severe-wear applications. As solid sheet with manganese and nickel content, WELLBRAZE has 17-20% work hardening factor and increases in toughness with use. WELL-CLAD has impact and wearing, chromium-carbide overlay applied to low-carbon steel (.12 max) substrate that absorbs impact resulting from heavy service. Composite material can be rolled or press-brake formed without separation.

STMicroelectronics    Lexington, MA 02421
Dec 29, 2005 Designed to protect static-dissipative equipment from damage or degradation caused by overvoltage transients, ESD Diode Arrays offer ESD protection up to 15 kV for 1-5 lines. Featuring 2 ESD diodes in SOT883 package, Model ESDALC6V1M3 offers 7 pF capacitance and can be used for 1- or 2-line ESD protection. Models ESDA(LC)6V1M6 and ESDA(LC)6V1-5M6 are 4- and 5-line ESD diode arrays offering 2 different levels of capacitance in Micro QFN package.