Norplex Micarta    Postville, IA 52162
Jan 10, 2006 Manufactured from multiple plies of woven fiberglass, which is saturated with epoxy resin and compressed under heat and pressure, NP571HT provides mechanical strength at continuous temperatures up to 210°C. Product also provides machinability, dimensional stability, and creep resistance. In use, it maintains physical, mechanical, and electrical properties for up to 1 decade. Composite is suited for applications in power generation, oil and gas, and aerospace.

Westfall Mfg. Co.    Bristol, RI 02809-2721
Jan 06, 2006 Suitable for any fluid handling system, variable flow Model 2900 utilizes 2 in-line wafer type mixers, one fixed with 0.9 Beta ratio and one variable with 0.7 Beta ratio and that adjusts incrementally to adapt to changing flow conditions. Featuring automatic modulation to maintain 3 psi regardless of flow rate, mixer flattens head loss at max flow, while providing consistent mixing over 20:1 turndown ratio. Sizes range from 3/8-120 in. ID.

Sonobond Ultrasonics    West Chester, PA 19380
Jan 05, 2006 Suited for chemical and industrial liquid applications, Filter Collar Bonder(TM) ultrasonically attaches rigid plastic circular frames to non-woven filter bags using SureWeld 20(TM) technology. Operator loads plastic ring and filter bag onto center fixture. Start button is activated causing welding head to close on part, ultrasonically weld it, and retract. Operator then manually rotates center fixture 60° and repeats process 6 times to achieve 360° weld.

Carver, Inc.    Wabash, IN 46992 0544
Jan 05, 2006 With no hydraulics, E-Series provides clean, quiet operation suited for compression molding rubber/elastomers, gum silicones, TPRs, thermosets, and plastics, as well as bonding and laminating applications. All electric power/drive system provides ramping of clamp force from 1,000 lb to 30 tons. Standard temperature range is to 650°F, and platen sizes range from 12 x 12 in. to 24 x 24 in. Functions can be programmed with microprocessor-based control.

Bekaert Specialty Films    San Diego, CA 92123-4359
Jan 04, 2006 Spectrally selective Panorama® Hilite 70 helps meet daylighting and solar control needs of architectural properties by blocking over 99% of damaging UV radiation and 95% of uncomfortable IR heat, while not noticeably affecting visible light transmission. Optically clear, polyester-based glass coating, applied to interior glass surface, helps eliminate hotspots around windows and glass doors, balance room temperatures, and reduce energy costs.

Wellington Alloys    Franklin, MI 48025
Dec 30, 2005 Used to fabricate plates, chutes, and hoppers, WELLBRAZE and WELL-CLAD suit high- and severe-wear applications. As solid sheet with manganese and nickel content, WELLBRAZE has 17-20% work hardening factor and increases in toughness with use. WELL-CLAD has impact and wearing, chromium-carbide overlay applied to low-carbon steel (.12 max) substrate that absorbs impact resulting from heavy service. Composite material can be rolled or press-brake formed without separation.

STMicroelectronics    Lexington, MA 02421
Dec 29, 2005 Designed to protect static-dissipative equipment from damage or degradation caused by overvoltage transients, ESD Diode Arrays offer ESD protection up to 15 kV for 1-5 lines. Featuring 2 ESD diodes in SOT883 package, Model ESDALC6V1M3 offers 7 pF capacitance and can be used for 1- or 2-line ESD protection. Models ESDA(LC)6V1M6 and ESDA(LC)6V1-5M6 are 4- and 5-line ESD diode arrays offering 2 different levels of capacitance in Micro QFN package.

Hobart Brothers Co.    Troy, OH 45373-2900
Dec 26, 2005 Quantum Arc copper coated mild steel wire has shiny surface finish with consistent lubrication that promotes feedability, while stable arc ensures smooth weld beads with minimal weld discontinuities and spatter. Offered in ER70S-3 (Quantum Arc 3), ER70S-6 (Quantum Arc 6), and ER80S-D2 (Quantum Arc D2) AWS classifications, product comes in 0.35, 0.45, 0.52, and 1/16 in. wire diameters, packaged in fiber spools, wire baskets, drums, and reels.

Cortec Corp.    St. Paul, MN 55110
Dec 22, 2005 Clean, Preserve and Protect (CPP) Program restores metal parts and equipment to operational specification, preventing disposal and subsequent replacement costs. Designed for use where sandblasting is not applicable, 3-step treatment system utilizes chemistries to remove corrosion from metal parts, clean parts, and preserve restored parts. Program is available in various systems, including environmentally friendly, biodegradable, and zero VOC processing.

Caplugs    Buffalo, NY 14207
Dec 21, 2005 Suited for finishing industry, Flex500Plus material provides high-temperature masking protection in powder coating, plating, painting, anodizing, and chemical processing applications. It is designed to withstand service temperatures beyond 500°F and addresses all requirements of traditional finishing processes. Use of product in molding process results in parts that combine high temperature resistance, complex designs, and flexible material.

IRC, Advanced Film Div.    Corpus Christi, TX 78411
Dec 15, 2005 Providing thermal conductivity to polymer-based insulated metal substrates, Anotherm(TM) is insulated by chemically grown, anodized dielectric layer with solderable screen printed conductors. It eliminates need for additional heatsinks and features uniform thickness of 35 microns, with no potential for delamination or peeling. Max operating voltage is 250 Vac, with thermal impedance at 0.2°C/W, and max continuous operating temperature is 400°C without solder mask.

Dow Corning Corp.    Midland, MI 48686 0994
Dec 15, 2005 Able to squeeze down during application for increased contact surface, InstantGlaze® II facilitates application and installation of glass for residential and small commercial window and door manufacturers. Soft texture promotes elasticity and elastic recovery performance. Product features 24 hr pot life and up to 15 min of open time, develops instant green strength, and bonds to vinyl, wood, glass, aluminum, paint, and fiberglass.

Kinetic Instruments, Inc.    Bethel, CT 06801
Dec 13, 2005 Suited for bench top and automated UV curing applications, SpotCure-B6 is available with 2 interchangeable light probes to cure UV adhesives in 365 and 395 nm ranges. In automatic operation mode, light activates ON when probe is removed from holder, and OFF when replaced in holder. Light delay of 1.5 sec allows accurate positioning of 12 mm light probe over work area, while selectable 10 sec timed cycles up to 60 sec and manual mode allow accurate control of curing time.

Premix Thermoplastics, Inc.    Milton, WI 53563
Dec 12, 2005 With conductivity less than 1 x 10⁵, PRE-ELEC 12-000 conductive compounds are based on copolymer polyacetal with carbon black or carbon fiber additive, while PRE-ELEC 12-031 compounds can be colored without affecting electrical properties. Ranging from 1 x 10⁹ to 1 x 10¹¹ §Ã™, PRE-ELEC ESD 12-000 static dissipative compounds are colorable alloys of copolymer polyacetal and inherently dissipative polymers.

TPE Solutions, Inc    Shirley, MA 01464
Dec 08, 2005 Featuring 20 to 90 Shore A hardness range, Softlink 900 Series TPEs allow lowering of friction coefficient to improve abrasion resistance. Off-white or easy-to-color compounds can be processed without preheating or drying and offer matte finish. Used in 2-shot molding, compounds can substitute for silicone, latex, or rubber in power tools, hand tools, appliances, and consumer products.

Speedline Technologies Inc.    Franklin, MA 02038
Dec 08, 2005 With max temperature of 662°F, lead (Pb)-free OmniFlex(TM) 10 Reflow Oven features variable-speed, closed-loop blower control; power limiting, balanced gas flow; and dual-chamber heating design. Process width is 20 in., heated length is 148 in., and and cooling length is 50.5 in. Lead (Pb)-free Electrovert VectraElite(TM), combined with UltraFill nozzles and upper High Velocity Convection pre-heat module, incorporates ServoJet spray fluxer and roll-out solder pot design.

JRI Industries, LLC    Springfield, MO 65803
Dec 07, 2005 With automatic operation, closed-loop, countertop Model JR-1 cleans using only hot water and biodegradable detergents. It includes motor-driven rotating basket and multiple spray bars on top, bottom, and side, all equipped with V-Jet nozzles. Washer operates on 110 or 220 V and is suited for various applications including automotive and industrial. Oil removal system, low water shut-off, oil absorbent pads, and portable cart are optional.

Quadro Engineering Corp.    Waterloo N2V1A1  Canada
Dec 07, 2005 Available in 4 sanitary and industrial designed models offering liquid throughputs from 3 gpm, ZC5 is engineered to incorporate and disperse powders into liquid stream in single-pass. Rotor/stator design enables shearing of powders prior to hydration, producing homogeneous dispersions free of lumps and fish-eyes. Vacuum permits concentrations up to 25% by weight to be generated with minimal air entrainment. Design eliminates over-processing and wastages.

Mearthane Products Corp.    Cranston, RI 02921
Dec 06, 2005 Formulated to have constant high coefficient of friction to promote uniform feeding, self-cleaning Pick Pads are made from Durethane F/C, a chemically blown or mechanically mixed/frothed cellular foam with closed cell structure. Pads provide volume resistivity from E8-E10 ohm-cm at hardness of 10-95 Shore A. Pick pads are used in paper feed and advance systems to move paper, plastic film, and other thin film substrates from trays and transfer them to rollers.

Binks ITW Industrial Finishing    Glendale Heights, IL 60139
Dec 06, 2005 Available in 3 model options to suit non-agitated, rotary agitated, and oscillating agitated applications, 2-quart SG-2 Plus(TM) delivers continuous mixing capabilities. Four-screw lid design facilitates hose attachment, while divorced design of regulator and handle aids in maintenance. Dual-regulation is provided for rotary agitation models, and all models incorporate check valve that prevents paint clogs in internal spring.