ChemMasters, Inc.    Madison, OH 44057
Jun 06, 2006 VOC-compliant in areas affected by Ozone Transport Commission (OTC) regulations, solvent-based A team products cannot freeze, will not settle out, and are not susceptible to bacteria growth. Products included in series are styrenated acrylic sealer; non-yellowing acrylic cure and seal; and high-gloss, non-yellowing sealer. Also included, Silencure-A offers long-term silane protection, while Crystal Clear-A delivers long-term gloss and protection.

Union Process, Inc.    Akron, OH 44313
Jun 05, 2006 Produced with motors from 60-125 hp to suit application at hand, SD-100 is designed to grind ceramic materials such as alumina and zirconium in metal-free environment. Mill is automated to run in batch mode with pneumatically operated discharge valves and is equipped with tungsten carbide sleeved arms. Ceramic-lined tank has gross capacity of 155 gal.

Kurt Manufacturing Co., Industrial Products Div.    Minneapolis, MN 55413 1540
Jun 05, 2006 Utilizing 30 hp main motor, Model 1200 Chipmunk compacts up to 1,200 lb of chips per hr. High-volume system produces dense aluminum chips with its 8:1 compaction ratio. Aluminum material and coolant are saved, as is floor space for storing and handling scrap and coolant. Machine is suited for small- and large-scale chip producing operations.

Newson Gale, Inc.    Lakewood, NJ 08701
Jun 05, 2006 Designed to monitor Type C containers, Earth-Rite Flexible Intermediate Bulk Containers (FIBC) System provides verification that bag's anti-static construction is functional and that it is correctly grounded. Interlock design allows product transfer only when resistance through container is less than 1 x 10⁸ ohms. Should unacceptable readings be registered, alarm signal LED is lighted and system remains inoperable.

Hobart Brothers Co.    Troy, OH 45373-2900
Jun 02, 2006 Designed for A514, A710, and similar HSLA and Q and T steels, Tri-Mark TM-101 gas-shielded wire offers tensile strengths in 105,000-115,000 psi range. It is available in .045 and 1/16 in. diameters and features smooth, stable arc, low spatter, and flat bead profile. Quick freezing slag also makes wire suited for high deposition welding on either single or multiple pass applications.

Hexis USA LLC    Corona, CA 92880
Jun 01, 2006 Resistant to water, most oils, diluted acids, alcohol, and hydrocarbons, 65 µm Imitation Gold S5245 vinyl films feature permanent solvent-based adhesive and are suited for vehicle and fleet graphics, long-term permanent markings, and corporate signage. They are offered in 10 yd increments in various widths from 15-60 in. in punched and unpunched versions.

Victrex plc / Victrex USA Inc.    Greenville, SC 29615
Jun 01, 2006 Based on VICTREX® PEEK(TM) polymer and Celazole® polybenzimidazole, TU-60, TL-60, and TF-60V products are designed to be melt processable and capable of performing in demanding high-temperature applications requiring optimized strength, wear, hardness, creep, and thermal properties. They offer suitable replacement for metals and non-melt processable high-temperature plastics.

Laird Technologies    Chesterfield, MO 63017
Jun 01, 2006 Offering high temperature and voltage properties, thermally conductive and electrically insulating T-preg(TM) HTD is used to isolate copper circuit layers from aluminum or copper base plate when making metal-based PCBs. RoHS-compliant product has UL relative temperature index rating of 150°C. HTD boards and substrates are compatible with Sn-Pb and Pb-free solders as well as surface mount and chip and wire assembly processes.

Huron Technologies, Inc.    Leslie, MI 49251
May 31, 2006 Formulated for use with spray elastomeric and castable urethane compounds, Mold Release Agents facilitate release of foam parts from mold. In most cases, water-based agents dry with no additional heat source. Products are environmentally friendly and contain no hydrocarbon solvents that are present in solvent-based release coatings.

Stratasys, Inc.    Minneapolis, MN 55344 2020
May 31, 2006 By expanding mechanical properties of prototypes, photo-polymer FullCure(TM) Tango line offers feel of rubber or silicon and stretch to mate with other components. TangoBlack(TM) and TangoGray(TM) offer 61 and 75 Shore A hardness, respectively. Materials are suitable for manufacturers of products with pliable features, such as tires, toys, shoes, gaskets, keypads, over-molding, and flexible automobile trim components.

Lucifer Furnaces, Inc.    Warrington, PA 18976 2088
May 31, 2006 Designed for 2,450°F operation, HS Series employs silicon carbide heating elements, which are controlled off line with SCR power supply that automatically compensates for changes in element resistance. Furnace chamber is lined with ceramic fiber and heats to 2,200°F in 55 min. Available in single and dual chamber models in sizes from 6 x 6 x 12 in. to 12 x 18 x 24 in., furnaces feature heavy gauge sheet steel construction, platinum/rhodium thermocouple, and double-pivot horizontal swing door.

Master Bond, Inc.    Hackensack, NJ 07601
May 30, 2006 Master Bond Polymer System EP37-3FLSP bonds to substrates such as metals, glass, ceramics, plastics, and elastomers. Optically clear epoxy features electrical insulation properties and exhibits resistance to vibration, shock, and thermal cycling. Suited for large-volume castings, product has 20 Shore D hardness, 1,000 psi tensile strength, and over 400 V/mil dielectric strength. Pot life after mixing exceeds 10 hr, and full cure occurs within 4-7 days at ambient temperatures.

Huron Technologies, Inc.    Leslie, MI 49251
May 30, 2006 Designed for heat cured silicone rubber applications, EZR-311 semi-permanent, water based mold release coating produces high quality molded parts such as automotive engine gaskets and electrical insulators. It can be used at mold temperatures of 320-360ºF. EZR-311 works with single or multiple mold cavities and is available in 5-55 gal drums.

Integument Technologies    Tonawanda, NY 14150-6711
May 26, 2006 Peel-and-stick FluoroGrip® fluoropolymer films are installed to protect signs, steel and concrete structures, equipment, glass, and other surfaces in public places against paints, acids, dirt, and grime. Permanent, chemical covalent bond between film and adhesive withstands different stresses such as extreme temperature cycling, UV rays, and aggressive chemicals including acids. Films are suited for use in new construction or ongoing maintenance programs.

Modern Process Equipment, Inc.    Chicago, IL 60623
May 26, 2006 Designed to provide precisely-controlled uniform particle size distributions, Models IMD 1042 and 1052 high-capacity limestone Gran-U-Lizers(TM) use series of paired rollers to reduce limestone to 10-20 mesh finished product. System design allows use of micrometer-like settings for each pair of rollers, enabling precision particle size adjustments. Other features include high-speed motor drive configuration and precision, and automatic roll gap control.

GBC Materials Corp. Div., Morgan Advanced Ceramics    Latrobe, PA 15650
May 26, 2006 VX Crucibles operate under severe conditions including temperatures up to 1,450ºC and extreme thermal shock conditions. They offer thermal expansion of 6 x 10^-7/°C at 1,000°C, low specific gravity, low thermal conductivity, and high electrical resistivity. Available in various shapes and sizes, products are suited for brazing, sintering, melting, and heat treating applications in dental, jewelry making, and metal brazing industries.

Merquinsa North America Inc.    Seabrook, NH 03874
May 25, 2006 PEARLCOAT® Activa TPUs provide functionality for fabric melt coating and extrusion coating applications, such as antimicrobial resistance, conductivity, and fire resistant compounds. Offered in clear or colored pellets, thermoplastic urethanes are suited for fabric coatings for belting such as conveyor belts used in airports, distribution facilities, and grain handling, as well as consumer products such as life jackets, life rafts, and sports/outdoor clothing.

Rohm & Haas Co.    Philadelphia, PA 19106 2399
May 25, 2006 Ultrafill(TM) 4000 series of levelers and suppressors are targeted at sub 65 nm node for interconnect metallization. Levelers allow customers to dial-in specific amounts of dopants into ultra pure copper films that enhance Via Stress Migration results. Suppressors feature wetting capabilities that deliver optimal gap filling on thin copper seed layers.

Uniloy Milacron, Inc.    Manchester, MI 48158
May 24, 2006 Model UMA 20.SH uses parison suction technology to produce elongated and curved 3D automotive and appliance parts, flash-free and with uniform wall thickness, from high-temp engineering resins. Engineered for 640°F melt temperatures, machine can be equipped for sequential co-extrusion of 2-material parisons and enables molding of components with stiff and flexible sections. Modular design allows interchangeability between suction-blow and blow-molding.

Scapa North America    Windsor, CT 06095
May 24, 2006 Scapa 707 polyester film is double coated with silicone adhesive on one side and acrylic adhesive on other. With operating temperature range of -20 to +350°F, conformable tape contours to intricate parts and offers chemical resistance and quick stick properties. High tack acrylic adhesive on Scapa 707 bonds to plastic, glass, and metal substrates, and is supplied with silicone coated paper release liner to aid in die-cutting.