Chemineer, Inc., A Unit of Robbins & Myers, Inc.    Dayton, OH 45401
Jun 27, 2011 With design that facilitates seal maintenance, Model 20 HT/GT modular agitators eliminate need to lift or remove gearbox. Replacement of mechanical seal is done by rotating gearbox 90° around pivot pin. Seal pedestal top opens for clear, line-of-site view and provides ample room for removal of coupling half and seal assembly. Other components include gearbox optimized for efficiency with helical gearing and parallel shaft configuration. Available range of speeds promote process control.

EV Group Inc.    Tempe, AZ 85284
Jun 27, 2011 Available as option on EVG850TB and EVG850DB automated temporary bonding and debonding systems, In-Line Metrology Module can detect variety of thin-wafer process irregularities and defects, including total thickness variation of carrier wafer, adhesive layer, bonded stack, and thinned wafer; bow/warp of bonded stack; and voids in bond interface. Adding in-line metrology to thin wafer processing enables ramp-up of 3D-IC and TSV manufacturing from pilot-line to volume production.

Toray Plastics (America)    North Kingstown, RI 02852
Jun 23, 2011 Available for CPGs and converters, Torayfan® CBH and CBLH biaxially-oriented clear barrier polypropylene films are designed for used as mono-webs and alternatives to PVdC-coated film. Torayfan CBH friction properties, seal-initiation temperature, and heat-seal window accelerate processing and manufacturing. Additionally, Torayfan CBLH film offers improved sealant layer that provides greater seal strength and hermetic seal. Both films protect against moisture-vapor transmission.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jun 22, 2011 Combining Teflon®-coated fiberglass tape with silicone adhesive, Pyro-Tape 682-CR is suited for insulating pipes and ductwork, and as non-stick covering for chutes, slides, heat-seal bars, and molds. Tape is rated from -100 to 500°F with adhesive strength of 50 oz/in. and tensile strength of 120 psi. Pyro-Tape 682-CR is available in standard sizes of ½ and 1 in. wide x 36 yards with cross-sectional thickness of 0.009 in.

SWECO®, Div. of M-I L.L.C.    Florence, KY 41022
Jun 21, 2011 Supplied in open-manifold or Packed-Vessel configuration, SWECO® Hydrocyclone System provides fine particle separation for wet processing. Manifolds utilize 2, 4, 5, or 10 in. diameter cyclones while Packed Vessels contain either 1 or 2 in. diameter cyclones. Both configurations can process feed rates from 10-3,000 gpm, depending on size and number of hydrocyclones installed in system. Reliable operation only requires consistent feed at steady pressure.

Cortec Corp.    St. Paul, MN 55110
Jun 16, 2011 Used to loosen frozen/rusted parts or as mold release, EcoLine® CLP maximizes life of machine parts by reducing friction and wear in addition to providing corrosion protection. USDA certified biobased product is non-flammable, non-toxic, and freeze stable and can be removed with common detergents. Safe for use on all metals and most plastics, multifunctional cleaner/lubricant/penetrant (CLP) leaves behind persistent layer that protects against corrosion for up to 24 months.

Kafko International Ltd.    Skokie, IL 60076
Jun 15, 2011 Oil Eater TableTop Parts Cleaner features environmentally-friendly, water soluble solution that flows through integrated cleaning brush. Measuring 13 x 5.5 x 14 in., it has 5 gal capacity and comes with 1 gal bottle of Oil Eater Original cleaner/degreaser. Cleaner has high-impact plastic body, corrosion-resistant pump and on/off switch, and removable lid that keeps tank clean when not in use.

RTP Co.    Winona, MN 55987
Jun 15, 2011 Glass fiber-reinforced polylactic acid (PLA) compounds, optimized for strength, stiffness, and thermal performance, target durable and semi-durable applications. Engineered bioplastic compounds offer sustainable alternative to traditional hydrocarbon-based thermoplastics. Fully colorable, PLA bio-polymers have glass fiber loadings from 10%-40%; 30% grade has 16,500 psi tensile strength, 1,630,000 psi flexural modulus, and 320°F heat deflection temperature at 66 psi.

Siemens Water Technologies    Warrendale, PA 15086
Jun 15, 2011 AquaCarb CX Series combines microporous structure of coconut shell-based carbon with kinetics of bituminous coal-based carbons. This provides alternative to coal-based activated carbon for surface water treatment, where taste and odor removal, disinfection byproduct (DBP) or DBP precursor removal, and total organic carbon (TOC) removal are required. Product can also serve groundwater applications.

Builders Automation Machinery    Largo, FL 33773
Jun 14, 2011 Remediator pressure cleans off mold, dirt, stain, and contamination from lumber and then moves it into chamber, where mold inhibitor is applied. This mold repelling machine allows lumber that has been sitting at lumber yards and home improvement centers for longer periods of time than recommended to be treated and re-entered into inventory as good lumber. Also, excess lumber from building sites can be restored to like new condition.

Guyson Corporation of U.S.A.    Saratoga Springs, NY 12866
Jun 14, 2011 Designed for surface preparation in coating work cells, Robotic Grit-Blasting System features 6-axis robot arm that serves as blast gun manipulator. Arm is attached to 52 x 32 in. rotary blasting cabinet with servomotor-driven 24 in. turntable controlled as seventh axis of coordinated robotic motion. Key to elimination of over-/under-blasted surfaces is ability to constantly maintain exact blasting angle, nozzle-to-surface distance, and surface speed while precisely following part contours.

US Products    Coeur D'Alene, ID 83815
Jun 13, 2011 CRI-certified PEX series has upright dolly design with roller handles to facilitate maneuvering and transport. For maintenance, hinged tank opens for full access to internal components. Wand caddy has retractable hose wrap, and rear wheels are sized to facilitate going up and down stairs. Available models include PEX 500 and PEX 200, which are adjustable from 50 to 500 and 200 psi, respectively.

Bergquist Co.    Chanhassen, MN 55317
Jun 10, 2011 Suited for use between high-power electrical device requiring electrical isolation and its heat sink, Hi-Flow® 650P thermally conductive phase change material offers thermal impedance of 0.20ºC-in.²/W at 25 psi. Top side is dry to touch, bottom side has natural tack, and polyimide film reinforcement provides dielectric strength as well as cut-through resistance. Appropriate uses include power supplies, IGBTs, discrete components, and automotive applications.

Bergquist Co.    Chanhassen, MN 55317
Jun 10, 2011 Gap Pad® VO Ultimate is fiberglass reinforced, silicone-based material that is suitable for use on surfaces with high roughness or uneven topography. Fiberglass carrier on one side offers optimal puncture resistance, and has slight inherent tack, minimizing any shifting during assembly. Available in standard sheet size of 8 x 16 in. and thicknesses of 20-125 mil, conformable, elastic product is also offered as die-cut parts in any shape or size.

Terronics Development Corporation    Elwood, IN 46036
Jun 10, 2011 Incorporating PLC-based control system and powder-processing technology, custom-designed seasonings applicator enables range of powders to be applied at precisely controlled weights uniformly on product. Deposition depends on powder properties and can range from gravity-driven to smoke-like dispersion. System includes all mechanisms necessary for taking powder from bulk sources and depositing them, containing them, and capturing any percentage not applied to product.

Turbex Ltd    Alton   United Kingdom
Jun 09, 2011 Versa Mk III offers automatic loading via programmable logic control that supports basket weight of 10 or 20 kg, while manual and semi-automatic handling allows loads up to 30 kg to be processed. System includes 7-day timer and panel on each tank for control of functions such as dunking and fine filtration. Utilizing degassing to remove air dissolved in water caused by emptying and filling tank, unit can include any number of tanks with either 40, 80, or 120 L capacity.

Interstate Products, Inc.    Sarasota, FL 34233
Jun 07, 2011 Approved for use on all non-food contact surfaces, "1" STEP neutralizes existing rust and acts as primer on both rusted metal and previously painted surfaces. Product can be sanded, top-coated with suitable paint, body puttied, or left as is. Non-flammable and non-toxic, water-based treatment can handle light freeze during storage and remains effective after it thaws. It is not recommended for rust stains on moving parts or on hot areas such as barbecues or engines.

Alliance Polymers & Services    Romulus, MI 48174
Jun 03, 2011 With Shore A hardness range from 10-85 A, styrenic A-Series Maxelast® TPEs can be overmolded onto PC, APS, PC/ABS, or copolyester substrates. Benefits include soft, flexible feel with optimized grip characteristics and compression set as well as processing and coloring characteristics. Also available in translucent and clear grades, TPEs resist scratching and are suited for use in such products as power and hand tools, personal care items, computers, consumer electronics, and auto parts.

Graymills Corporation    Chicago, IL 60613
Jun 03, 2011 Compliant with freeboard ratio/rule of .75, Handikleen(TM) model PL36-FB features 16/18 gauge steel construction with powder coated exterior and removable work shelf. Upon removal of shelf, 20 gal unit may be used as soak tank. Built-in filtration and pump deliver cleaning and rinsing action through flexible metal flush hose, and bottom drain facilitates fluid change-outs. Other features include abrasive-resistant, 170 gpm pump; external drain shelf; and 170 gph flow.

Graymills Corporation    Chicago, IL 60613
Jun 03, 2011 Made of heavy gauge metal with powder coated exterior, TL Series Liftkleen(TM) Semi-Automatic Washers accommodate parts up to 47 x 18 x 24 in. For water-based applications, units are available in stainless steel with insulated tank and thermostatically adjustable heat up to 180°F. Electro-pneumatic lift mechanisms provide 300 lb capacity with adjustable stroke/speed settings. Automatic open-and-close lid, filtered detail brush, and recirculation pump allow spot cleaning of hard-to-reach areas.