Materials & Material Processing

Material Handling & Storage, Materials & Material Processing

Pallet Handling Conveyor is chain-driven.

January 8, 2002

Model 25-CREZD roll-to-roll accumulation conveyor combines intelligence of EZLogic Accumulation system with efficiency of EZ Drive System, which eliminates many mechanical components. Accumulation zones range from 30 to 120 in. in length, each of which contains a drive. Drive is turned off when there are no pallets present or when pallets are accumulated. Read More

Materials & Material Processing

Solder Paste eliminates tombstone defects.

January 7, 2002

Loctite® Multicore® 63S4 RP15 phased-reflow, no clean solder paste is formulated with 63S4 alloy. 63S4 alloy blends SN63 and SN62, with melting points of 183°C and 179°C respectively. In phased reflow process, small amounts of SN62 wets both sides of termination before SN63's melting point is reached, tack-soldering components to PCB, and delivering larger assembly process windows. Read More

Materials & Material Processing, Robotics

Robots feature servo control and color LCD touch screen.

January 4, 2002

IT Series robots can be mounted on injection molding machines from 50 to 550 tons with vertical stroke requirements of 650 to 1000 mm. Traverse stroke ranges between 1200 and 1500 mm, and payload ranges between 10 and 20 lbs. ITW Series robots have telescoping arms, and can be mounted on 50-850 tons with vertical stroke requirements of 700 to 1700 mm. Traverse stroke ranges between 1200 and 2000... Read More

Materials & Material Processing

Parts Washer purifies mechanical parts.

January 2, 2002

Model PW-005 Zee Line Parts Washer removes particles, soil, or other impurities from mechanical parts. It has capacity of 5 gal, solvent capacity of 3-1/2 gal, and fusible link steel cover that closes automatically in event of flash fire. Read More

Materials & Material Processing

Liquid Crystalline Polymer is a single-clad laminate.

January 2, 2002

ZYVEX(TM) liquid crystalline polymer circuit material is designed for high performance electronics where high frequency, chemical resistance, and fine line high density interconnect (HDI) requirements are critical. ZYVEX TeraClad meets industry requirements for low/stable dielectric constant, low/stable dielectric loss, extremely low moisture absorption, high chemical resistance, matched in-plane... Read More

Materials & Material Processing

Polyester Film features haze levels of 0.4%.

December 27, 2001

Lumirror® U50, available in thicknesses from 47 to 200 Gauge, provides consistent surface finish and clear base. It reduces high angle sun haze, and does not have chemical surface slip treatment, which can increase scratches and interfere with subsequent processing. Film is not prone to static issues, pitting/pimpling, or uneven unwind and rewind. Read More

Adhesives & Sealants, Materials & Material Processing

Encapsulant/Potting Material exhibits <1% shrinkage.

December 27, 2001

Ceramacast(TM) 510 aluminum oxide based, hydraulic-setting ceramic compound potting material can be used to encapsulate cartridge heaters and embed high temperature components to 3200ºF. Supplied as dry powder, Ceramacast 510 is bonded using calcium aluminate and as-cast. Its dried density is 180 lbs/ft3, and it exhibits exceptional thermal conductivity and dielectric strength of 75-100... Read More

Materials & Material Processing

Circulation Attritor can adapt to existing Q machines.

December 27, 2001

QL circulation grinding Attritor includes holding tank that is typically 10 times Attritor size. Specially configured arms speed up grinding and create more agitation. Unit's high circulation/pumping rate consists of holding tank contents passing through Attritor at ~8 times an hour. Grinding media for QL range in size from 3/32 to 1/4 in. in diameter. Typical media include chrome steel,... Read More

Materials & Material Processing

Static Mixer offers concave mixing elements.

December 27, 2001

Kenics® KMX static mixer's concave elements promote cross-stream flow. Each element is approximately 1 pipe diameter in length, and consists of multiple intersecting blades, which generate fluid layers as mixture flows downstream. Features include ASME-certified design and fabrication, diameters up to 24 in., no moving parts, and no external power or regular maintenance. Sheets of low... Read More

Materials & Material Processing

Flame Retardant Materials have no halogens.

December 27, 2001

Based on polytrimethylene terephthalate (PTT), RTP 4700 series glass reinforced, non-halogen, flame retardant polyester compounds are available with glass levels of 10% to 33%. It has flexural strength of 23,000 psi, dielectric strength of 500 V/mil, and HDT of 410°F @ 1.82 Mpa. It has UL 94 VO listing. Read More

Materials & Material Processing

Stripping Pot cleans magnet wire.

December 21, 2001

Magnet Wire Stripping Pot removes film insulations from magnet wires of all sizes, types, and configurations. Wires are dipped into stripping solution to remove insulation without causing any mechanical stress or abrasion to wire. Units are available in 2 models: DSP1 has temperature control and DSP2 has programmable control for selecting and maintaining exact temperature. Both models are... Read More

Materials & Material Processing

Boron Rings are oriented radially.

December 18, 2001

Made of sintered neodymium iron, single-piece Boron rings have radially oriented magnetic field. Because ring is single piece, and all grinding processes can be done prior to magnetizing and assembly. Polarization is single pole on outside with opposite pole on inside of ring, or alternating configuration with multiple poles on OD or ID. Parts can be magnetized in assembled state, or externally.... Read More

Materials & Material Processing

Extruder reprocesses low bulk density foam.

December 17, 2001

Scrapper(TM) dual-diameter extruder features large diameter screw section equipped with deep flights to mix and break down materials, while small diameter section is dedicated to melting, pumping and removing excess gases and volatiles. Feed section is cored for water-cooling and contains knives to assist in feeding of roll stock. Steel, fixed weldment base allows for mounting of smaller diameter... Read More

Materials & Material Processing

Fluoroelastomers feature reduced post-cure time.

December 17, 2001

Tecnoflon HS Family Fluoroelastomer products allow fabricators to reduce in-plant energy consumption, speed throughput of end products, and reduce need for inventory of their products. When injection- or compression-molded into O-rings, seals and other precision components, HS fluoroelastomers exhibit reduced mold fouling. They meet industry specifications, including MIL-R-83248C. Read More

Materials & Material Processing

Steel Turning Grades increase tool life.

December 17, 2001

KC9110 and KC9125 have coating bonding technology that can apply 3 main layers and several sub-layers of coating with total thickness of 18 microns. Grade KC9110 is ISO class P10 grade for finishing operations while Grade KC9125 is P25 class grade for universal machining on all types of steel. Both have coatings 25 to 75% thicker than company's conventional coated carbides and increase... Read More

Materials & Material Processing

Developer Replenisher is highly concentrated.

December 17, 2001

DR-501CR aqueous developer replenisher is a 1-part concentrate formulated for developing fully aqueous dry film photoresists and photoimageable solder masks. It is suitable for use in feed and bleed systems, requiring fewer additions than more diluted carbonate solutions. DR-501CR reduces volume of solution to waste treat. Read More

Chemicals & Chemical Processing, Materials & Material Processing

Corner Cushions protect products from damage.

December 13, 2001

Corner Keeper protectors are made from extruded polyethylene foam to provide non-abrasive surface areas and protection against multiple impacts. Protectors are fabricated from closed-cell polyethylene foam extrusions. Cylindrical profile is pneumatically cut to produce shape that mimics 3-dimensional, 90° angle, enabling protectors to fit around multi-planed edge of cube shape products. Read More

Materials & Material Processing

Desoldering Ribbon is an alternative to braided wick.

December 13, 2001

Constructed with 4 layers of fine precision copper screen wire mesh, Matrix® Desoldering Ribbon removes more solder than conventional wick. Dispenser with spring guide permits accurate placement while keeping operator's fingers safe from heat. Ribbon is available in 3 widths with rosin flux, no-clean flux, or bare copper. It features permanently static dissipative dispenser and is clean-room... Read More

Materials & Material Processing

T-Slotted Extrusions are available in 2 series.

December 11, 2001

Metric T-Slotted Extrusions, available in 25mm and 40mm series, feature smooth surfaces and ability to use either fractional or metric hardware. Typical industry applications include machine frames, cleanrooms, machine guards and enclosures, lighting, material handling equipment, and prototype equipment. All structures can be assembled using hand tools. Read More

Materials & Material Processing

Security Kit marks devices to thwart thieves.

December 11, 2001

Secure Marking Kit leaves invisible identification mark on servers, PCs, laptop computers, software CDs and other valuable office or personal assets. Kit includes hand held ultraviolet lamp, 3 UV marking pens, equipment inventory form and security labels. UV pens can mark wood, plastic, metal, glass, cloth and paper. UV lamp illuminates identifying marks. Kit comes with CD containing 38 security... Read More