KLA-Tencor Corp.    San Jose, CA 95134
Aug 19, 2011 Suitable for chip manufacturing at 20 nm device nodes and below, eDR(TM)-7000 electron-beam (e-beam) wafer defect review system addresses defect imaging and classification challenges at leading edge or located at bottom of deep trench/hole. System can drive directly to site of defect at high resolution, enabling review of multiple defects per second. Features include stage and vibration-isolation system as well as reticle defect review and voltage-contrast imaging modes.

J. W. Winco, Inc.    New Berlin, WI 53151
Aug 18, 2011 Available in inch and metric sizes, series GN 303.1 is suited for use wherever parts have to be clamped in confined space or in particular lever position. Insert is connected to lever via serrations, which can be disengaged in order to swivel to ideal clamping position. Serrations automatically re-engage when lever is released. Handle is zinc die-cast and ergonomic pushbutton is nylon plastic, while insert, spring, and screw for push button are stainless steel.

Thomas & Betts Corp.    Memphis, TN 38125
Aug 17, 2011 Available in ¼-20, 3/8-16, and ½-13 thread sizes, Kindorf® Fast Set Beam Clamps are load rated at 250, 600, and 1,000 lb, respectively, and require no tools for installation. Once clamp is slid onto I-beam flange and secured by hand, threaded rod can be screwed through clamp and tightened, thereby locking tongue of clamp against I-beam for extra security.

Key Technology, Inc.    Walla Walla, WA 99362
Aug 12, 2011 With stainless steel bed and vertical acceleration limited to almost 1 g, Iso-Glide(TM) features technology that achieves what resembles horizontal motion to maximize sanitation, gentle handling, and quiet operation. Conveyor can perform various product handling and packaging distribution functions, including scale feed applications, and supports various mounting methods. In-field adjustable speed and stroke allow rate at which product moves to be varied.

Davey Compressor Co. Div., Jenny Products Inc.    Somerset, PA 15501
Aug 11, 2011 Driven by 5 hp electric motor that requires single-phase, 230 V power source, J5A-30P single-stage compressor includes ASME-certified, 30 gal air tank. Integrated 4-cylinder J pump with compression ratio produces 19.4 cfm at 100 psi or 19 cfm at 125 psi. Pneumatic tires and lifting handles promote portability, and air shroud and flywheel help keep pump temperature low. Other features include splash lubrication system, manual tank drain, safety relief valve, and pressure gauges.

Schenck AccuRate    Whitewater, WI 53190
Aug 11, 2011 Offered in models with 12 and 24 in. belt widths, DEA Open Frame Weighbelt Feeder provides weight controlled feeding, weight indication, and totalization for fragile materials like cereals, snack foods, kibble, fruits, and pasta. System features tool-less belt removal, IP69K stainless steel load cell, 316 stainless product contact surfaces, and shaft-mounted, washdown drive system for power transmission. Feed rates up to 2,660 ft³/hr are achievable.

RIDGID    Elyria, OH 44035
Aug 11, 2011 Designed to hold PVC, steel, and copper pipes, TRISTAND® Model 460-6 has 1/8-6 in. capacity, while Model 460-12 has 12 in. jaw and extended chain to grip pipe from 1/8-12 in. Integrated ground lug provides conductive surface to connect weld ground, while jack screw helps stabilize units during use. Both are self-hooking for pipe up to 4 in., which helps when second hand is not available to engage chain into wear plate. Pipe benders are located at rear of base for bending or adjusting pipe.

Continental General Tire, Inc.    Charlotte, NC 28241
Aug 10, 2011 CrossContact LX20 with EcoPlus Technology is all-season tire that promotes safety and fuel efficiency. Traction Grooves, biting edges in tire grooves, shorted stopping distance on wet ground as well as provide traction and grip on snow. Also included, Smooth Response Technology contributes handling efficiency and road noise reduction. EcoPlus Technology employs temperature-activated functional polymers and grip-enhancing additive that help reduce wear and increase fuel efficiency.

Tharo Systems Inc.    Brunswick, OH 44212 0798
Aug 10, 2011 Designed for moderate- to high-speed operation, PA500w can print and apply 100+ labels/min to top, side, or bottom of products. Included product sensor and controller ensure accurate label placement, while wipe-on brush ensures proper adhesion to smooth flat surfaces as well as uneven surfaces. Capabilities handle application of labels, ranging from 3 x 1 in. to 4½ x 7 in., to materials such as cartons, tray and blister packages, bags, and cans.

Wilden Pump & Engineering Co.    Grand Terrace, CA 92313
Aug 10, 2011 Providing supplementary pumping action to remove pressure variations on discharge side of AODD pump, SD Series Equalizer® is suited for paint and coating operations where there are changes in pumping pressure and flow rate. Unit minimizes pipe strain and water hammer and protects in-line equipment. Available in multiple sizes from ½-3 in., SD Equalizer comes in ductile iron, 316 SS, aluminum, polypropylene, PVDF, and carbon-filled acetal to satisfy temperature and chemical-compatibility needs.

Numerex Corp.    Atlanta, GA 30339
Aug 10, 2011 Using rugged tracking tag, satellite solution provides worldwide coverage and can also be used as wireless sensor hub. Years of uninterrupted service are possible using one field-replaceable battery, and unit can be installed, activated, and operational in less than 1 min. In addition to movement tracking and configurable reporting parameters, functionality enables monitoring and alerting of sensors, from door open/close or air temperature to flow rate and tank level.

Memory Protection Devices    Farmingdale, NY 11735
Aug 09, 2011 Supporting CR2032 batteries and available in both through hole and surface mount versions, Snap Dragon Holders have dual pressure contacts made of nickel-plated phosphor bronze and are covered with gold flash overall for corrosion resistance. LCP base piece is capable of withstanding up to 280°C for reflow solder processes. With height of just 4.83 mm above PCB including cover piece, holders are suitable for automotive products, handheld electronics, key fobs, and industrial equipment.

Anver Corp. - Anver.Com    Hudson, MA 01749
Aug 09, 2011 To compensate for unevenly packed loads with staggered rows, Anver VPFL4 lifts heavy pipe or tube, in and out of containers, from top without using slings or hooks. Nylon centering guides and oval rubber suction cups prevent anything other than nylon or rubber from touching load. With 500 lb capacity, lifter can simultaneously pick up 2, 3, or 4 pipes or tubes. Air-powered or electric units require 8 in. of headroom, and features include adjustable handle with built-in controls.

PDC International Corp.    South Norwalk, CT 06854
Aug 09, 2011 Featuring stainless steel frame, upstream photo-eyes, and Allen Bradley touchscreen interface, 50 Series ShrinkSealers apply tamper-evident banding and shrink sleeve labeling at up to 130 cpm, continuously. Systems run 40-50 micron banding materials and are compatible with all petroleum-based and sustainable films, including PVC, PET, PETG, OPS, and PLA films. Material can range from .375-3 in. D and .625-7 in. H. Modules for both vertical and horizontal perforations are available.

Interstate Products, Inc.    Sarasota, FL 34233
Aug 09, 2011 Made from military grade materials, IPI Fuel Bladders are suited for storing potable water, wastewater, fuels, chemicals, dielectric oil, and alternative or blended fuels. Tanks utilize variety of geomembrane fabric materials with 3 in. overlap on seams. Fabrics are matched to application to resist temperature extremes, humidity, UV exposure, abrasion, and corrosion. Available with variety of connections, fittings, and valves, collapsible cells provide temporary and long term storage.

SKF USA, Inc.    Lansdale, PA 19446
Aug 08, 2011 Reducing need for manual maintenance, SKF Hydraulic Driven Lubricator automatically lubricates construction and off-highway equipment attachments using integrated pump driven by hydraulic oil itself. Integral pump feeds proper lubricant in appropriate amount at right time, and delivery rates can be adjusted or reset to meet operating requirements. Installed directly on attachment, unit performs ideally with chisel paste and helps increase machine availability as well as worker safety.

Rockwood Manufacturing Co., Inc.    Rockwood, PA 15557
Aug 08, 2011 Key operated from outside with turn piece on inside, LP Series integrates contemporary postmount style door pull with deadbolt locking system. Cylinder and thumbturn location eliminates physical strain when locking and unlocking, while design facilitates mounting. Able to be used on multiple swinging and sliding door types, product can incorporate Yale® 1109 rim cylinder or Yale K680 SFIC housing or be provided without cylinder. Multiple locking options and custom sizes are available.

Essemtec Ag      Switzerland
Aug 08, 2011 Designed for electronics manufacturing and LED assembly, Scorpion can be equipped with up to 4 different dispensing valves and is built on Paraquda machine base that enables dispensing of up to 100,000 dots/hr with ±25 µm accuracy. XY-portal is built on mineral cast chassis, which provides damping and smooth motion at high speeds. For production of high volumes, Twin Dispensing mode enables 2 valves to dispense simultaneously on 2 different locations with adjustable distance.

SentrySafe    Rochester, NY 14625
Aug 05, 2011 Designed to protect digital media, documents, jewelry, and other valuables from fire, water, and theft, FIRE SAFE Big Bolt Series features full-length pry-resistant hinge bar and may be bolted to floor to prevent unauthorized removal. Units are UL Classified for 1 hour fire endurance up to 1,700°F. For increased security, select models come with dual key lock that works in conjunction with either primary combination or electronic lock.

Air Technical Industries    Mentor, OH 44060
Aug 05, 2011 Equipped with specially-designed hopper, mobile universal lifter-dumper will lift and invert (up to 180°) any shape or size of container desired in order to safely dump its contents. Self-propelled unit offers variable-speed control from 1 fpm to 4 mph and 90° left/right steering. V-shaped dumping chute is designed to retain control of item regardless of its shape, and stop bars prevent container from sliding out during dumping. Optional conveyor bottom is available for automated loading.