Anver Corp. - Anver.Com    Hudson, MA 01749
Mar 14, 2011 Featuring rectangular suction pads that adjust to curvature of top surface, VPFL Air-Powered Vacuum Lifter lets one person handle cylindrical loads of up to 2,000 lb without blocking, chains, and slings. Full lengthwise support prevents bending and sagging, while 2 alignment guides facilitate attachment. Ergonomic, below-the-hook lifter also offers adjustable handlebar to accommodate loads of varying widths as well as vacuum leakage sensor that triggers audible and visual alarms.

Keystone Electronics Corp.    Astoria, NY 11105
Mar 11, 2011 Available in single- and dual-cell configurations, SMT and THM Lithium-Ion holders for 18650 batteries feature heat-resistant Nylon housings and Gold-plated Phosphor Bronze contacts. Battery installation and/or removal does not require tools, and design accommodates lead (Pb)-free solder as well as traditional reflow processes. Suited for THM and SMT use, holder helps meet demands for higher-energy, lightweight, rechargeable batteries for consumer and industrial electronic products.

Midland-ACS    West Midlands   United Kingdom
Mar 10, 2011 Featuring one diaphragm regulator coupled to spring-tensioned poppet valve, dual-redundant OPD Stemsaver guards against any failure of filter-regulator that controls compressed air system pressure. Product can be set to regulate pressure from 58-116 psi as standard and is intended for pneumatic control systems used for valve actuation in oil, gas, and other processing industries. Fabrication is of 316 stainless steel to meet anti-corrosion requirements of environments such as offshore platforms.

Aero Tec Laboratories, Inc. (ATL)    Ramsey, NJ 07446
Mar 09, 2011 Made of rubberized ballistic nylon, FueLockers(TM) serve as auxiliary and direct supply tanks for generators, engine-pump sets, extended range vehicles, and ferry-flight operations. Bladders accommodate gasoline, E10 bio-fuel, diesel, kerosene, bio-diesel, 100LL, bio-butanol, and all jet fuels. Available in 5 sizes from 100-500 gal, FueLockers are fitted with 2 in. cam-lok quick-fill for direct-pump or nozzle filling, and ½ or 1 in. outlets for engine fuel-line connection and aux-to-main transfer.

General Machine Products Co.    Trevose, PA 19053
Mar 09, 2011 With Cable Feeding Sheaves, utility cable can be smoothly fed into conduits and innerducts from any angle. Steel units accommodate 2-6 in. Schedule 40 and Schedule 80 ducts and feature half-circle, split-tube design that facilitates insertion and removal. Available in aluminum alloy or wear-resistant Nylatron®, sheave rollers utilize maintenance-free, self-lubricating bearings. Sheaves are bright yellow for visibility in dark work environments.

Insite Solutions, LLC    Wake Forest, NC 27587
Mar 09, 2011 Kaizen Cart empowers employees to maintain floor markings with Superior Mark floor tape, which ensures everyday floor markings stay clean and bright to maintain OSHA compliance. Holding up to 10 rolls of tape as well as all tools and supplies necessary to maintain floor markings, cart features 8 in. rubber tamper roller to ensure proper adherence of pressure sensitive tape. Also included, customized magnetic color code chart displays company's floor marking color code.

Sunnen Products Co.    St. Louis, MO 63143
Mar 08, 2011 Suited for oil and gas industry, Model HTG-10000 accommodates standard parts up to 30 ft long with 2-24 in. ID and up to 26 in. OD standard, or up to 48 in. as option. Machine features 100 fpm max stroke velocity, 0-300 rpm spindle, and tool feed force of up to 2,500 lb. Hydraulic feed system provides servo position control of feed system actuator, electronic pressure control, closed loop feedback, and ability to operate both standard and 2-stage tooling.

Screen Machine Industries, Inc.    Pataskala, OH 43062
Mar 08, 2011 Measuring 60 ft x 36 in., track-mounted wireless remote-controlled conveyor can match up to any track mounted crusher or screening plant for on-the-fly, finger-tip mobility. Counterweighted design, combined with heavy-duty channel frame build, enhances stockpiling capability, while hydraulic top fold and cylinder positioning facilitates setup as well as transportation between job sites.

Northfield Precision Instrument Corp.    Island Park, NY 11558
Mar 08, 2011 Featuring 3 in. diameter, hydraulically actuated, internal grip Collet Chucks mount on tilting table to drill angled hole. Fixed stop pad picks up inner face of automotive work piece while chuck expands and pulls back to grip part. Chucks repeat to 1/10,000 T.I.R. and have low profile that enables 8 chucks on one table.

Lincoln Electric Co., Inc., The    Fort Wayne, IN 46825
Mar 08, 2011 Compatible with up to 2,200 lb bulk stems as well as wood reels, Stem and Wood Reel Dispensing System allows accurate wire placement when using 1/16-3/16 in. dia wire. Horizontal dereeler, featuring heavy-duty design, offers large diameter wire dispensing speeds to 250 (ipm) and up to 800 ipm for smaller diameter wire. Motorized operation helps eliminate challenges such as wire flip, flux-cored wire splitting, excessive tip wear, pulsating, and burn back.

Asymtek    Carlsbad, CA 92008
Mar 07, 2011 Designed to jet 0.1-0.2 mm dots through windows as small as 0.4 mm into LED cavities, Spectrum(TM) S-920N automatically maintains consistent shot weight with software-managed dispense parameters. Closed-loop dispensing eliminates need for constant operator adjustments. Non-contact fluid dispensing system is suited for manufacturing side-view LEDs, which are used to illuminate displays in devices such as tablet computers, smart phones, and e-readers.

FleetwoodGoldcoWyard    Romeoville, IL 60446
Mar 03, 2011 Tight Pitch Live Transfer Conveyor utilizes 0.3 in. pitched chain wrapped around ¼ in. nosebar to minimize deadplates from chain-to-chain transfers, which helps to eliminate product skewing. Unit is designed to be driven off existing chain with no need for motor, and is also available as standalone conveyor. It is suited for companies that process shrink wrap packs and corrugated 4-, 6-, 8-, and 12-packs.

Novellus Systems, Inc.    San Jose, CA 95134
Mar 03, 2011 Equipped with 2,100 mm OD lapping wheel, AC-2100L microLine® can process up to twenty 300 mm prime silicon wafers in one batch with sub-micron precision. It can also process up to eight 450 mm wafers. Along with independently driven inner and outer pin rings, features include automatic force calibration, in-situ wafer thickness metrology, and contactless gauges. Latter controls lapping wheel gap dimension, ensuring repeatable within-batch and batch-to-batch wafer thickness.

Safe Conveyor, Inc.    Swansea, MA 02777
Mar 03, 2011 Modular Plastic Belt Incline Conveyor enables product transfers from under equipment to containers as high as 43 in. (fills Gaylord bins on pallets), facilitated by adjustable angles up to 60° and removable guide rails combined with pin-less belting. Maintenance free and repairable unit has heavy-duty aluminum extruded design and utilizes variable-speed drive that can move products at rates to 25 fpm while using less than ¼ A from standard 115 Vac.

Nordson Corp., Packaging Systems    Duluth, GA 30097
Mar 01, 2011 Combining traditional slot nozzle and rotating bar technologies, TCHP TrueCoat Slot Applicators provide stripes or full coating in continuous web coating processes. V-shaped body design enables flexible setup of web routing and guidance. Featuring quick-change filters and modules as well as flange-on solenoids, hot melt adhesive applicators offer standard application widths up to 31.5 in. and are suitable for coating papers, foils, films, and nonwoven materials.

Winkle Industries    Alliance, OH 44601
Mar 01, 2011 Designed for typical mag-grab applications, where scrap magnets are permanently fitted into top of grapple, OptiMag G-Series is fabricated to order with required fitting to suit any make or model of grapple. Deep-field magnets allow grapple operators to sweep work area without changing attachments or leaving cab. Units can maintain 75% duty cycles in continuous 24/7 operation.

Proper Storage Systems, Inc.    Seguin, TX 78155
Mar 01, 2011 With Full Extension Pneumatic Roll-Out Shelving Racks, users can store and access heavy tooling and materials. Units offer shelf widths from 36-66 in. and shelf depths of 36 or 48 in. in 2-, 3-, and 4-shelf models. Automatic safety interlock locks in all other shelves when one shelf is extended. Shipped fully assembled, racks include all necessary anchors.

Labjacks.com    Buffalo Grove, IL 60089
Mar 01, 2011 Designed for industrial and laboratory applications, Xtreme-Z Lab Jacks come in 4 models with lift heights from 4.5-12 in. All are stable under minimum or maximum load, with ±.015 in. deflection over full range of movement. Largest model offers respective dynamic and static weight capacities of 150 and 250 lb. All models feature adjustment handle that is removable and machined to accept powered movement. Mounting top and bottom plates are standard and metric grids, respectively.

Stakrak Ltd    West Sussex RH11 9SH  United Kingdom
Feb 28, 2011 Used in lean, JIT (just-in-time) manufacturing and concession stockholding environments, Kanban side storage racking system facilitates storage of components at point-of-use on production line. It can be adapted and modified to fit requirements and is suited for smaller components such as fasteners and fixings. Options include all-metal shelves with plastic bins, or racks with particle board decks and plastic bins. Dual-bin arrangement simplifies stock rotation and replacement.

Key Technology, Inc.    Walla Walla, WA 99362
Feb 28, 2011 Using close-coupled high-speed ejector system made up of 256 air jets spaced 6 mm apart, G6 Tegra® sorters remove foreign material and product defects from acceptable product stream. Auto Valve Check feature, by automating routine testing of ejection system valves, enables food processors to detect potential problems and take appropriate corrective action so sorter operates at peak performance. Check can be initiated by operator or OPC command from network and takes 10-25 min.