IWKA Pac Systems, Inc.    Fairfield, NJ 07004
Jul 21, 2005 Designed to meet and exceed GMP standards, TFS 80-1 Tubefilling Machine provides optimal access to dosing system and all work stations. Clean, modular design facilitates thorough cleaning and reduces changeover times for size changes and fitting of different tube closing systems. With output rates to 100 tubes/min, machine employs horizontal tube transport system and servo-driven orbital tube transport system. Dosing range is 1-400 ml.

Automated Control Systems, Inc. (ACS)    New Haven, IN 46774 1362
Jul 21, 2005 To maximize unattended winding capacity, automatic Wyndamster 3210 incorporates 10-reel operation with side-by-side reel design. It coils any product strip up to 2.5 in. wide and accommodates reels up to 30 in. in dia. Operating at speeds up to 650 ipm, machine can function in overwind or underwind mode; complete conversion from one direction to other takes less than 1 min. Features include tangential feeder and paper interleaf with programmable tension control.

Anver Corp. - Anver.Com    Hudson, MA 01749
Jul 21, 2005 Designed for picking up non-porous surfaces, Model HC-108D consists of 2 hand suction cups and removable turnbuckle assembly that pulls them together for setting of seam. Turnbuckle assembly, providing fully adjustable tension for pulling pieces together, has reversing gear for quick release after setting. While unit provides 300+ lb side pull capacity at 4 to 1 safety factor, multiple tools can be used on larger countertops and floors as needed.

Speedline Technologies Inc.    Franklin, MA 02038
Jul 21, 2005 Camalot® XyflexProâ„¢ HVB (High Volume Batch) Dispenser uses conveyorless material handling system and dual dispense heads. Throughput rate is achieved by optimizing number of parts in process to fully absorb capillary flow times, part transport times, and extended product heating times. Max dispense head utilization provides ability to process 16 boats/96 parts within dispense area. Underfill solution also offers single station magazine loading/unloading.

Thomas & Betts Corp.    Memphis, TN 38125
Jul 20, 2005 To install one-piece Angler? Clamp, user snaps apart 2 halves of strut strap, fits to pipe or conduit, slides pre-threaded bolt through keyhole-shaped opening in strap, and tightens. Extruded, tapped threadform holds it securely. Bent tab design allows clamp halves to be assembled and bolt to extend up at 30? angle, providing installer access to bolt with screwdriver or power tool. Strap is sized to fit snugly to EMT, rigid conduit, IMC, and standard pipe sizes.

Alimak Hek, Inc.    Houston, TX 77061
Jul 20, 2005 Offering fully modular vertical transport solution, Scando 650 is available in single- or twin-car configurations, with 2-motor DOL, 2-motor FC, or 3-motor FC. Units offer payloads of 1,500-3,200 kg/car, speeds up to 65 m/min, and maximum lifting height of 400 m. Various types of doors and gates are available.

Meese Orbitron Dunne Co. (MOD)    Saddle Brook, NJ 07662
Jul 19, 2005 Able to accommodate loads up to 700 lb, MOD 100P features internal rib design and steel-top ring that optimizes cart's structural integrity and load bearing capacity. Roundtrip configuration features 2 repositionable, ventilated plastic shelves, while one-way cart includes non-removable wire shelves. Industrial strength casters are standard and truck is available with bag hook, hanger bar, and vacuum stand options as well as choice of steel or plastic base.

Phihong USA    Fremont, CA 94539
Jul 19, 2005 With quick disconnect for 3 individual loads, 1,500 W, 1U Model PSM1554 accepts three PSM500 500 W power supplies. Unit is available with 48 V main and up to 30 A, and 12 V standby up to 4.5 A. Operating from input voltage of 90-264 Vac with active power factor correction, rack is hotplug and n+1 configurable for scalable and redundant applications. Each output is individually protected against overloads that cause overheating of wiring from excessive current.

ITW Rocol North America    Glenview, IL 60025
Jul 19, 2005 Accu-Lube® 9045 attaches to 3-pump Accu-Lube® applicator system and applies smooth coat of lubricant directly to cutting edge and on both sides of saw blade. Nozzle mixes lubricant and air right at nozzle, so there is no lag time and no dry cutting. Mounting block facilitates installation, blade changes, and alignment.

Bosch Rexroth Corp., Corporate Headquarters    Hoffman Estates, IL 60192-3707
Jul 19, 2005 VarioFlow™ Workpiece Pallet System handles products up to 8 kg in weight and requires only one drive in many applications. To provide best possible surface for product transport, workpiece pallets are available in custom lengths of 80–500 mm. Featuring Adaptive Modularity™, system is available in widths from 65–320 mm in aluminum and stainless steel. It is suited for linking machine tools and manual workstations, as well as supplying parts to assembly process stations.

Durham Manufacturing Company, The    Durham, CT 06422-2108
Jul 15, 2005 Offered in 3 models, Rotabin® systems consist of circular revolving steel shelves, dividable into triangular bins, mounted in stacks on vertical stem or axle. Space-saving solutions facilitate viewing and picking of parts from one spot. Series 1300, 1200, and 1110 offer up to eight 34 in. dia shelves, ten 28 in. dia shelves, and ten 17 in. dia shelves, respectively. Series 1300 has 5 permanent compartments per shelf, and each shelf will hold up to 500 lb.

Cobar Solder Products    Londonderry, NH 03053
Jul 15, 2005 Constructed of polypropylene, refillable Flux Pen features fine tip that allows user to apply liquid flux to tiny chip components and individual solder joints on densely populated assemblies. Flux is dispensed by squeezing barrel, and transparent cartridge shows amount of remaining material. Design minimizes waste and prevents over-fluxing, which reduces cleaning time and prevents contamination. Ergonomic pen fits into top pocket of lab coat.

Hitachi Power Tools    Norcross, GA 30093
Jul 14, 2005 Designed to withstand jobsite use, 5.5 hp EC2510E incorporates cast iron pump and oversized oil level sight glass. Base plate integrated control panel protects gauge, regulators, and plumbing while centralizing all controls to facilitate in-field use. Product cycles from 116-145 psi and also features pneumatic throttle control, over-sized flywheel and head scoop, braided stainless steel exhaust, shielded cross over tube, and ball valve tank drains.

Vi-Cas Mfg. Co., Inc.    Cincinnati, OH 45236
Jul 13, 2005 With ½â€“12 in. widths and lengths to 12 in., oblong vacuum cups and bellows handle pick-and-place applications of cylindrical objects like pens, bread, candy bars, capsules, tubes, and other hard to handle items. Handling of uneven surfaces is achieved with cushioning effect of bellows design. Cups and bellows are available in anti-static and food-grade materials.

Triple E Corp.    Lowell, MA 01852
Jul 13, 2005 Single-Camâ„¢ ejector handle is designed for direct replacement of plastic VME card ejector handles to provide additional 1/8 in. cam travel for positive board disengagement from backplane connectors. Made from solid extruded aluminum, handle offers strength and durability in harsh environment applications. It is available with or without custom front panels created with downloadable design kit.

Heartech Precision Inc.    Elk Grove Village, IL 60007-5617
Jul 12, 2005 Featuring adaptable sealing system, Model JNC140-EDM can be used in submersible applications with EDM dielectric fluids. Auto Air Purging system removes any possible condensation accumulation inside indexer housing. Indexer has stainless steel faceplate with 140 mm dia and center height of 110 mm. Table center through-hole dia is 28 mm and max work dia is 140 mm. Maximum workload is 136 lb when mounted vertically and 275 lb when mounted horizontally.

Igus, Inc.    East Providence, RI 02914 0349
Jul 12, 2005 Used to guide and protect moving cables and hoses attached to automated machinery, System E4 cable carriers are available with crossbar that attaches along inner or outer radius and accommodates conduits up to 11.8 in. dia. Crossbar connects to side links directly or can be used in combination with 2 standard snap-open crossbars to provide management of additional cables and hoses.

Kurt Manufacturing    Minneapolis, MN 55421
Jul 12, 2005 Suited for mid-size and larger machining centers, HDL ClusterTowersâ„¢ feature 8 stations, each with 6 in. width, 4 in. openings, and clamping force to 6,316 lb at 70 lb of torque. Quick-change jaws lift off vise module with half-turn of hex key, and reset and self-align with no special tools. Self-adjusting holding block enables clamping of same or dissimilar sized parts, while adjustable pre-load feature minimizes handle turns for opening and closing clamping stations.

Imagineering Finishing Technologies    South Bend, IN 46619
Jul 12, 2005 Lead- and Cadmium-Free Electroless Nickel surface finish is electroless nickel process yielding mirror bright nickel phosphorus alloy that offers corrosion resistance, uniformity of coverage, and repair and salvage capabilities. Trivalent Chromate Conversion Coating produces protective coating on pure aluminum, zinc, and anodic aluminum. It minimizes corrosion, provides bonding surface for paints, and appears faint blue to tan and iridescent.

Bel-Art Products    Wayne, NJ 07470
Jul 07, 2005 Suited for low volume users, Frigimat® Cub Dry Ice Maker can be attached to liquid CO₂ cylinder and produce 250-350 gram block of dry ice in minutes. Production can be viewed through translucent polycarbonate body that opens without clamps or screws. System operates at low pressure and incorporates multiple pressure relief safeguards.