Material Handling & Storage

Material Handling & Storage

Lift Trucks provide vibration-free power.

November 9, 2001

Cat® 8,000-11,000 lb capacity lift trucks feature pneumatic tires, and are offered with gas, LP gas and diesel engine configurations. Cabs include contoured seats and flexible operator restraint systems as well as open-step frames. Tilt steering column is adjustable within a 12° range of motion. Other offerings include Hydrostatic steering system, pusher fan arrangement and fingertip... Read More

Material Handling & Storage

Temperature Control System applies sealants and plastisols.

November 8, 2001

Integrated Metering and Temperature Control System ensures that robot-applied, single-component sealants or plastisols are applied at controlled flow rate and pre-set temperature. System controls material temperature and dispenses material at variable flow rates according to commands from servo drive. Fully automated for production applications, control system communicates with robots through its... Read More

Material Handling & Storage, Welding Equipment & Supplies

Wire Feeder operates at speeds from 50 to 780 ipm.

November 8, 2001

Model 714S bench style wire feeder features one tool-less, rotatable drive assembly and automatic run-in. Dual tension control provides independent drive roll pressure on front and back rolls, while trigger hold allows extended welds. 714S runs hard and cored wires from 0.023 to 1/8 in. dia at speeds from 50 to 780 ipm. Spool size capacity is 60 lb, and incorporates Posifeed(TM) four-drive-roll... Read More

Material Handling & Storage

Large Crane handles rough terrain.

November 8, 2001

The 130 ton RT9000E crane provides mobility, maneuverability and pick-and-carry capabilities. It has a five section 42 to 160 ft boom that provides a 169 ft maximum tip height and 140 ft maximum radius with 3,770 lb capacity. Cab has tinted safety glass, armrest-mounted single-axis controllers, hot water heater, air fan, sliding side and rear windows, sliding skylight with electric wiper and... Read More

Material Handling & Storage, Mechanical Components and Assemblies

Cylinders are available with bore sizes from 3/4 to 8 in.

November 8, 2001

Q6 Hydro-Line Cylinders come with pressure-energized nitrile rod seals and nonmetallic piston wear rings. Pre-lubricated from factory, cylinders are suitable for non-lubricated air service up to 250 psi. Q6 NFPA-interchangeable cylinders feature precision-machined aluminum end caps and self-aligning, externally removable rod cartridge assemblies. Hydraulic HQ6 tolerates pressures to 400 psi, and... Read More

Material Handling & Storage

Bridge Handles feature counter bored mounting holes.

November 8, 2001

Ergostyle® Bridge Handles are made from glass-fiber reinforced technopolymer plastic with black matte finish, while mounting holes are counter bored for socket cap screws and have technopolymer plastic cover caps available in variety of colors. Slight bend in handle distributes force on fingers during use. Resistant to solvents, oils, grease, and other chemical agents, handles are also... Read More

Material Handling & Storage

Fluid Dispenser ensures critical deposit control.

November 8, 2001

Model 2000XL applies adhesives, epoxies and assembly fluids in amounts as small as 0.006 in. dia. It uses microprocessor circuitry to control amount of fluid applied. Teach function helps user determine correct amount of fluid to use for specific applications. Digital displays of all dispensing parameters provide process control. Up to 8 different deposit amounts can be stored in non-volatile... Read More

Controls & Controllers, Material Handling & Storage

Control Valves are used with air, intert gas or vacuum.

November 8, 2001

MicroKing 4-Way Air Control Valves are direct acting units designed to control actuators, pilot other valves, and for blow off and dispensing applications. They are available as inline or subbase versions offering M5 or 1/8 in. ports with flow of 0.18 Cv and 4.8 W solenoid. Valves feature built-in flow controls and choice of IEM or Subbase Bar manifolds with side or bottom porting, as well as... Read More

Material Handling & Storage

Bulk Container accommodates double blade mixers.

November 8, 2001

All-plastic intermediate bulk container accommodates double blade mixers for mixing multiple ingredients and raw materials. It enables food, chemical and other processors to mix and blend inside bulk container, eliminating need to mix in processing vessel and transfer to another container for shipping. It handles products with up to 1.5 specific gravity, stacks 2-high when full and 3-high when... Read More

Material Handling & Storage

Inventory Management System suits tank and silo inventory.

November 8, 2001

Mark III Yo-Yo® Inventory Management System provides accurate and reliable inventory management information for tanks and silos. Mark III is FM-approved and rated for use in hazardous environments. Its sensor is housed in explosion-proof polyester-coated, cast aluminum housing. It may be interfaced to computer, PLC, or Bindicator solid state readout. Bindicator readout displays levels to... Read More

Material Handling & Storage, Packaging Products & Equipment

Solder Dispenser ensures even solder mix.

November 8, 2001

Programmable LDS9000 bench top solder paste dispensing system eliminates tunneling, paste separation and waste. It has a hand-held gun with mechanically driven lead screw that gently and precisely pushes the solder mix through an industry-standard plastic syringe and tip. Linear actuator, which is under software control, moves plunger in syringe without crushing paste. It draws paste back at end... Read More

Material Handling & Storage

Reels stay together and keep products safe from damage.

November 8, 2001

Dead Bolt reels feature stay-tight bolt assembly for safety. They are available in variety of sizes to accommodate nearly any type material, and come fully assembled or ready for assembly. Reels have tapered start holes and multiple tie-off holes to reduce material waste, and are available with optional water resistant cores. They can be stacked, making transport, material handling and storage... Read More

Material Handling & Storage, Portable Tools, Safety & Security Equipment

Tool Lanyards comply with OSHA guidelines.

November 8, 2001

Miller® Bandit(TM) Tool Holder and Miller WristBandit Tool Holder prevent workers from dropping tools at heights. Miller Bandit Lanyard Tool Holder attaches to workers' waist belts while allowing freedom of movement. It is constructed of stretchable cord surrounded by nylon tubular webbing, and stretches from 26 to 43 in. Miller WristBandit Tool Holder attaches to workers' wrists using Velcro.... Read More

Material Handling & Storage

Bulk Wire Container features octagonal shape.

November 8, 2001

Marathon Pac(TM) corrugated structures are 100% recyclable and easily collapsed by hand. They require only wire conduit attachment bracket and conduit connector. Enclosed packaging with moisture barrier protects wire from dust, spray and splash. Spoolarc MIG wire is spooled into carton, eliminating cast and helix as wire exits from welding gun. Containers are available in range of wire sizes and... Read More

Material Handling & Storage

Vacuum Pumps are used for pick and place applications.

November 6, 2001

Fastbreak pre-assembled high speed blow-off vacuum pumps, levelers and cups are suitable for applications that require accurate part placement of irregularly shaped objects and/or rapid part release in dusty/dirty environments. Blow-off action continuously self-cleans vacuum lines to ensure positive release into nesting fixture for safe placement of parts. Applications include metal stamping,... Read More

Material Handling & Storage

Electric High Lift is available in 2 models.

November 6, 2001

Maxx-Jack Electric High Lift is capable of lifting skids, plastic pallets, wire baskets and containers with open bottoms. Unit includes 12 Volt electrical system with battery and charger. Push button lift and lower control is located in handle, and magnetic backed remote lift/lower control with 6 ft. cord is optional. Electric High Lift, with 2,200 lb capacity, includes automatic floor lock. Read More

Material Handling & Storage

Conveyors provide single solution for multiple applications.

November 6, 2001

Zig-Zag® Overhead Enclosed Chain Conveyors allow manufacturing and distribution centers to combine carton, tote distribution, and trash handling in one conveyor system that can integrate with existing floor conveyor systems. They automate manual functions and provide safer working environment. Read More

Material Handling & Storage

Scissor Lift is for low volume paint operations.

November 6, 2001

Self-propelled, curved rail guided scissor lift can access both sides and ends of product as it travels on floor guide rail. This pneumatic/hydraulic powered personnel lift travels from lowered platform height of 31 ft to maximum raised operator platform height of 144 ft. Its 30 x 66 ft operator platform features 500 lb capacity. Unit can be rolled off guide rail and used as stationary scissor... Read More

Material Handling & Storage

Smart Lift floats loads in assembly systems.

November 6, 2001

Computer-controlled iLift(TM) lifting and balancing system for assembly and material handling lets operators apply 2 lb of physical force to move 150-lb load at speeds up to 4.9 ft/sec. Float mode allows direct movement of loads without need to push buttons from central control position, thus shaving seconds from cycle times. In-line slide handle eliminates vertical overtravel. Lift can be... Read More

Material Handling & Storage

Stackers offer capacities to 4000 lbs.

November 6, 2001

Series W heavy-duty walkie stackers provide lift heights to 154 in. and operate from 24 volt electrical system. Comfortable dual twist grip controls forward and reverse travel. Buttons for raise, lower, and horn are located in center of handle for easy access. Button at end of handle reverses truck's travel direction away from operator should he/she come in contact with it. Speed cutout switch... Read More