New England Machinery, Inc.    Bradenton, FL 34203 5304
Apr 22, 2009 Offering positive pump placing control, positive container control, and positive torque control, Model NERPS/NERPC handles wide range of containers and/or pump combinations, including finger, lotion, and trigger, as well as non-pump caps. Unit applies correct torque upon placement of pump onto container, eliminating need for subsequent cap tightener. With change in positive guidance of dip tube, machine can straighten dip tube curvature up to 1/3 of overall length.

Rockford Systems, Inc.    Rockford, IL 61109 2695
Apr 17, 2009 Suitable for lathes, drills, mills, grinders, and band saws, Flexible-Arm Shields have spring steel arms covered with vinyl to protect against grease and oil. Arms offer virtually unlimited adjustment possibilities and direct or magnetic mounting. Direct-mount base can be fastened right on machine, while magnetic base consists of 3 in. diameter magnet with 100 lb holding force. Transparent portion of shield is constructed of 3/16 in. thick clear polycarbonate.

Independent Machine Co.    Fairfield, NJ 07004
Apr 17, 2009 Mounted to press or laminating operation, 12 x 12 in. modular Spool-Mate requires 220 V power source and speed reference to follow. Unit includes IMC Dancer Tension Controller for adjustable precision tensioning, AC vector follower drive with speed range to 250 fpm, core chucks for most core sizes, interface capability, and range of mounting brackets.

Posi Lock Puller, Inc.    Cooperstown, ND 58425 0246
Apr 14, 2009 PH-113IE, 3-jaw, 25 ton internal/external puller features internal, external and optional long jaws for pulling. Internal puller jaws have reach from 2.5-7 in. and spread from 8-21 in., while external jaws come with 12 in. reach and 2½-18 in. of spread with standard jaws. Optional long jaws provide 20 in. of reach and 1½-30 in. of spread.

NCMT Ltd    Surrey KT7 0QJ  United Kingdom
Apr 13, 2009 T-Slot Clean covers aid in comprehensive removal of swarf from T-slots in machining area of mill or machining center to accelerate changeover to subsequent batch runs. Products also reduce inaccuracies due to chips causing misalignment when component is clamped. Pushed into T-slots over all areas of machine table where they are not being used to clamp fixtures, strips are retained by spring-loaded sides, slightly wider than slots, that prevent swarf and coolant ingress.

Specialty Equipment    Houston, TX 77055
Apr 10, 2009 Made of all-welded, structural steel with 316 stainless wetted parts, dual-lance Model ADO-5520 automatically rotates each drum, locates and aligns bung openings, positions each drum at 6 o'clock, then shuttles drums to fill station where tare and filling is also automatic. When converted to twin pail filler by selector switch, machine indexes 2 containers directly to fill station then tares and fills two 5-gallon jugs, simultaneously. Fill rate is 8 pails per minute.

Schlitter Tool, Inc.    Warren, MI 48093 6036
Apr 10, 2009 With HexMaster(TM) Rotary Broaching Attachments, users can machine Hex, Double Hex, and other ID and OD shapes in seconds on most CNC lathes, mills, or screw machines with feed rates up to .012 ipr and speeds to 2,000 rpm. Attachments are suited for manufacturing military fasteners and defense parts.

Wilson Tool International Inc.    White Bear Lake, MN 55110
Apr 09, 2009 Opti-Bend tooling helps fabricators achieve lean manufacturing goals by eliminating secondary bending operations. With this solution, simple 90° bends can be made in thick turret or Trumpf-style punch presses. Tooling creates 90° wipe up form using rotating cam, built into die, that acts like press brake. Results include minimal to no sheet marking and fewer required hits. By enabling smaller bending operations on punch press, tooling can reduce part handling and setup time.

MAG IAS, LLC    Erlanger, KY 41018
Apr 01, 2009 Delivering repeatable process control as automated blade molding facility, CNC-controlled Rapid Material Placement System (RMPS) offers integrated manufacturing capable of spraying in-mold coatings, dispensing/lay-up of glass and carbon fiber materials, and dispensing/application of adhesive. Also available, quick-cure molding system produces molds using customer CAD data, yielding finished blade to spec with each cycle. It can be infused with resin in 1 hr and followed by 2 hr cure.

Qualitest International Inc    Fort Lauderdale, FL 33308
Mar 30, 2009 Models 142-20 and 142-40, featuring electro hydraulic drive, fully automatic test sequence, and switch off at specimen failure, respectively offer max drawing forces of 200 and 400 kN. Integrated 3D optical image analysis software, AutoGrid Vario, determines field of strain values in range of 0.5% to more than 100% without any unambiguity. By combining data collected from both systems, user is provided with true understanding of how sheet metal behaves during forming process.

JWC Environmental    Costa Mesa, CA 92626
Mar 25, 2009 Measuring 13 ft tall, Channel Monster XD 3.0 produces 7 tons of cutting force at peak loads. System combines rotating screening drums and Muffin Monster® grinder to shred solids while processing up to 59 million gallons/day. It features 15 hp grinder motor, 1 hp motor for drums, 3 in. hex drive shafts, and stainless steel coil drums with ½ in. diameter rod. System is suited for pump stations since grinder shreds rags, plastics, wood, and trash so particles flow through pumps and pipelines.

Schober USA, Inc.    Fairfield, OH 45014
Mar 24, 2009 Featuring tag dispenser with web tension relief, Model RFID-CP inserts UHF and HF inlays under die-cut blank or pre-printed labels and validates finished product. Control and monitoring is accomplished through pendant station which houses industrial PC. System works with transponders in accordance with ISO specifications, in widths from 20-80 mm. With inserter, pre-printed labels ranging from 101.6-203.6 mm wide can be applied at rates from 5,000-20,000 labels/hr.

Davis-Standard, Killion Specialty Systems    Pawcatuck, CT 06379
Mar 24, 2009 Capable of winding film in widths from 80-140 in. with single or dual winder configuration, PAC 60 uses center shaft support for 3 in. cores to wind multiple slit rolls to 30 in. OD, while 40 in. rolls are wound on 6 in. shafts. It comes with motorized roll cart and shaft puller fully integrated into PLC-based controller, which reduces operator lifting of shafts and promotes winding automation. For stretch film, lay-on roll eliminates air and improves film relaxation prior to winding.

Dalemark Industries, Inc.    Lakewood, NJ 08701
Mar 20, 2009 Printing, coding, and debossing systems of 975 Series accommodate range of flat products - blister cards, tyvek pouches, sleeves, labels, envelopes, cartons, discs - with dimensions from 1.5-14 x 1-13 x 0.075-0.187 in. Designed for short- and long-run imprinting, products are available with debossing, hot roller coding, flexographic plate printing, or ink jet coding capabilities. They can print horizontal or vertically at speeds up to 150 cpm.

Komax Corp.    Buffalo Grove, IL 60089
Mar 19, 2009 Fully automatic Zeta 651 and 655 allow for production of small batches and broad variety of harnesses with minimal changeover time. Base machines can carry 36 wire choices and several crimping stations, each with programmable height adjustment, and require no application-specific parts to change between setups. Measuring system monitors entire block loading operation, while force sensors control each insertion. Additional options are offered for wire marking and more processing stations.

NanoInk, Inc.    Chicago, IL 60607
Mar 18, 2009 Model NLP 2000 enables patterns of nano- to micro-sized features to be created using various materials, from metal nanoparticles to biomolecules. Capabilities enable researchers to design and create custom-engineered and functionalized surfaces using Dip Pen Nanolithography® technique to transfer nanoliter or smaller amounts over environmentally controlled area as large as 40 x 40 mm. Pens deliver spot size over range of 50 nm up to tens of microns.

Schleuniger, Inc.    Manchester, NH 03103
Mar 18, 2009 Built from modular components, TransferModule 6000 includes cable transport system, transfer shuttles, transfer chain, cable loading/unloading stations, control system, and PC-based user interface. Stations can perform stripping, tinning, sealing, shield flaring, and micro-flame soldering, as well as ultrasonic and resistance welding, connector housing insertion, and electrical testing. Typical applications include coaxial, flat, and round multi-conductor and zipcord cable assemblies.

Oil-Rite Corporation    Manitowoc, WI 54221 1207
Mar 16, 2009 Lubrication system, comprised of PurgeX® dispensing technology, 3-way air solenoid, and polypropylene ½ gal reservoir with low-level switch, delivers continuous bath of lubricant to cutting surfaces during CNC operations as well as moving parts of internal machinery. Featuring 4 in. aluminum body, PurgeX offers mechanics necessary for precise and repeatable lubrication cycles. Adjustment screw controls length of piston stroke and determines volume of fluid dispensed with each cycle.

Sonobond Ultrasonics    West Chester, PA 19380
Mar 11, 2009 Able to accommodate tinned or heavily oxidized wires, Dual Head SpliceRite(TM) welds wire bundles that have cross-sectional areas of up to 100 mm². It comes with 3,500 W power supply and utilizes Wedge-Reed system, which directs high frequency ultrasonic energy via welding tips to wires to be welded. Welding heads on each side of weld area enables accelerated splicing of large wire bundles. Up to 250 jobs can be stored/recalled, and welds may be controlled by height, energy, or time.

Flexicon Corporation    Bethlehem, PA 18020 8006
Mar 09, 2009 All-stainless Sanitary Bag Dump Station for pneumatic conveying systems collects dust created during manual dumping of bulk materials from bags, boxes, drums, and other containers and allows tool-free wash down. High velocity vacuum fan draws airborne dust from operator's atmosphere onto 2 cartridge filters, which are accessed by removing interior baffle, and replaced using quick-disconnect fittings. Unit is also available mounted on frames with casters for in-plant mobility.