Fuchs Lubricants Co.    Harvey, IL 60426
Mar 06, 2013 Intended for use by aerospace manufacturing industry, ECOCOOL 7830 B water-miscible cutting and grinding fluid is stable in hard water and low foaming in soft water without use of silicone defoamers. Fluid is designed for high-speed machining of aerospace aluminum and titanium alloys as well as ferrous materials. This product is formulated with bio-resistance for extended service life, lubricity to protect tools against wear, and detergency for machine and part cleanliness.

Quaker Chemical Corporation    Conshohocken, PA 19428
Jan 07, 2013 Designed for machining of aluminum alloys, QUAKERCOOL® 7000 ALF BAF machining and grinding coolant is water soluble as well as boron-free and amine-free. Low alkalinity properties aid in prevention of staining, while wetting abilities result in optimized cutting performance and microbiological growth control without biocide addition. Product also provides cleanliness on tools and machines with good detergency.

Master Chemical Corporation    Perrysburg, OH 43552
Oct 24, 2012 With VOC levels of less than 75 g/L as per Southern California AQMD Rule 1144, TRIM® OM 313 clean running straight oil does not contain any active sulfur, is free of chlorine, and does not stain parts. Suitable uses include form-tapping, thread-rolling, and Swiss screw machines. Offering oxidation inhibition for extended life, oil is proven on steel and bearing steel parts and safe for use on aluminum alloy and steel alloy parts as well as cast iron, copper, brass, and bronze.

Quaker Chemical Corporation    Conshohocken, PA 19428
Aug 29, 2012 Suitable for use with gray cast iron and alloy steels, QUAKERCOOL® 3511 can operate within range of 125-750 ppm hardness while demonstrating optimal foam control and fines handling. Bio-stable coolant was formulated without any secondary amines, chlorinated or sulfurized compounds, or phenolic ingredients. Product delivers corrosion protection characteristics to ensure rust-free parts, and exhibits optimal tramp oil rejection properties to extend bath life.

Walter USA, Inc.    Waukesha, WI 53188
Aug 03, 2012 Designed to exceed stringent coolant criteria in metalworking, ValCool(TM) VPLFC Cutting Fluid provides foam control properties, suited for high pressure systems rated 1,000 psi and up. Heavy-duty, non-chlorinated, semi-synthetic formula optimizes tool life and surface finish, and helps boost overall system cleanliness, rejecting tramp oils and maintaining stable pH levels. Product is available in 5 gal pails to 55 gal drums.

Wallover Oil Co., Inc.    Strongsville, OH 44136
Jun 25, 2012 Consisting of heavy-duty, chlorinated semi-synthetic coolant, WS 7450 forms transparent micro-emulsion when mixed with water. WS 7450HP has similar formulation but also offers foam control, making it suitable for high pressure CNC and grinding operations. Both can be used on wide range of metals, including stainless steel alloys, cast aluminum, ferrous metals, and cast iron.

MAG IAS, LLC    Erlanger, KY 41018
Jan 12, 2012 Formulated for machining titanium, hardened steels, and superalloys, CYCLO COOL® 900 and 5000 series are comprised of additive-free synthetic concentrates with near-neutral pH formulas. Both coolants are clear in use, promoting visibility in cutting zone. While low-foaming CYCLO COOL 900 series suits high-pressure, through-tool delivery systems up to 2,000 psi, CYCLO COOL 5000 non-staining anionic synthetic cutting fluid suits applications with delivery pressures of 300-400 psi.

Rust-Lick, Inc.    Glenview, IL 60025
Sep 28, 2011 Available in 5- or 55-gal containers, Ultracut 380R is effective in wide range of light, moderate, and heavy-duty applications, including machining, cutting, grinding, milling, broaching, threading, and turning. Hard water stable formula contains no DCHA, chlorine, boron, phenol, nitrites, triazines, sulfur, copper, or SARA 313 reportable chemistry. Product is recommended for ferrous/nonferrous metals, aluminum, titanium, brass, bronze, copper, and other high nickel alloys.

Rust-Lick, Inc.    Glenview, IL 60025
Feb 24, 2011 Hard water-stable and resistant to bacterial and fungus, ULTRACUT Pro is effective in light, moderate, and heavy-duty applications, including machining, cutting, grinding, milling, broaching, threading, and turning. Tight emulsion ensures consistent lubrication and cooling for optimized tool life and surface finish. Available in 5 or 55 gallon containers, ULTRACUT Pro contains no boron, phenol, nitrites, triazines, sulfur, copper, or SARA 313 reportable chemistry.

Rust-Lick, Inc.    Glenview, IL 60025
Jan 28, 2011 ULTRACUT Aero is bacteria- and fungus-resistant cutting fluid that is optimized for use with metals such as titanium, aluminum, Inconel, and stainless steel. Non-chlorinated coolant contains no sulfur, boron, phenol, nitrites, copper, or SARA 313 reportable chemistry and has extreme pressure additives for optimal surface finish. It is available in 5 or 55 gal containers and is suited for use in aerospace, medical, and electronics industries.

CIMCOOL®    Cincinnati, OH Oh. 45209
Aug 04, 2010 Designed for moderate to heavy-duty operations, CIMTECH 609® is suitable for use with most aluminum alloys, titanium, exotic alloys, cast iron, carbon steels, high-speed steel, high alloy steels, and stainless steels. Product offers drawability and biological protection for use in recirculating systems. With no smoke and minimal residue, low-misting fluid leaves no slippery film on parts, machinery, or floor. Corrosion inhibitors allow use on both ferrous and non-ferrous applications.

Sunnen Products Co.    St. Louis, MO 63143
Jun 16, 2010 Based on renewable vegetable formulation, SHO-500 cutting oil provides oxidation stability and is suited for honing applications where additives cannot be used, such as nuclear and some aerospace parts. Available in 5 gal pails, 55 gal drums, and 330 gal totes, oil can be used with conventional vitrified honing abrasives and metal-bond super abrasives.

ITW Rocol North America    Glenview, IL 60025
Jun 09, 2010 Made from naturally derived, vegetable-based oils, Rustlick PowerCool Green and PowerCool Green CF water-soluble oils are formulated to provide optimal lubricity and biostability in heavy-duty cutting and grinding applications. Products are safe for all metals and suited for light- to heavy-duty jobs. PowerCool Green contains chlorinated EP additives, while PowerCool Green CF contains non-chlorinated EP additives and is also recommended for use on titanium.

Blaster Chemical Co.    Valley View, OH 44125
May 10, 2010 Containing sulfur, chlorine, wetting, and anti-weld agents, light-colored Cut 'N Cool is suited for stainless steel, carbon steel, aircraft steel, cast iron, aluminum, and other hard alloys. Product's petroleum base helps prevent rust on machinery, tooling, and materials. Formulated to meet stringent environmental regulations, Cut 'N Cool comes in recyclable aerosol package.

ITW Rocol North America    Glenview, IL 60025
Feb 25, 2010 Formulated with chlorinated and non-chlorinated EP additives, respectively, Rustlick PowerCool MaxLife and PowerCool MaxLife CF coolants provide biostability and performance for heavy-duty cutting and grinding applications. They can be used on ferrous/non-ferrous metals, aluminum, brass, bronze, and copper. Available in 5 or 55 gal containers, products suit wide range of low to heavy-duty applications, including machining and milling. PowerCool MaxLife CF can also be used on titanium.

LENOX    East Longmeadow, MA 01028
Feb 24, 2010 Formulated with Extreme Pressure additive, CYCLE HD is suited for moderate to heavy-duty machining of ferrous and non-ferrous metals. Product resists bacteria, extending sump life and providing odor control. Fluid is prepared with small oil droplets that prevent separation of oil from water, which leads to stable emulsion. Low foaming and low misting, CYCLE HD offers optimal performance in sawing, drilling, milling, tapping, and turning applications.

Doall Sawing Products    Des Plaines, IL 60016
Feb 01, 2010 Providing tramp oil rejection and control of bacteria and mold, semi-synthetic Kool-ALL Ultra® extends sump life. Power-Cut Ultra® soluble oil has emulsifiers that mix with water and can handle alloy steels such as 300 series stainless steel. Featuring low foaming tendency, Synthetic Kleen-Kool Ultra® optimizes fines release and hard water tolerance, minimizing grinding swarf and maintaining unclogged grinding wheel. All use recyclable containers and liners that are tamper-resistant.

Rust-Lick, Inc.    Glenview, IL 60025
Dec 02, 2009 PowerCool coolants are safe for all metals, including ferrous/non-ferrous metals, aluminum, brass, bronze, and copper. Products can be used for wide range of low to heavy-duty applications including machining, cutting, grinding, and milling. Coolant is available in 2 versions, PowerCool contains chlorinated EP additives and PowerCool CF contains non-chlorinated EP additives. Both are available in 5 or 55 gal containers.

Henkel Corporation    Rocky Hill, CT 06067
Jul 30, 2009 Formulated to generate minimal foam and be used continuously for years with minimal biological degradation, Multan® B 236(TM) and B 414(TM) are semi-synthetic, water-soluble solutions for machining and grinding ferrous and non-ferrous alloys. Multan B 236, suited for most water conditions and multi-metal applications, offers optimal performance on cast iron and steel. With additional properties, Multan® B 414 contains more oil and is formulated with additional extreme pressure additives.

Genevieve Swiss Industries, Inc.    Westfield, MA 01085
Jul 09, 2009 Designed for soft and hard metal applications, Swiss Silver cutting oils eliminate wax-like buildup on machine's slide surfaces that can catch chips that create abrasion, loss of accuracy, and machine maintenance. All formulations are clear, and low viscosity results in less fluid use, less fluid carry out on parts, and less chance of tolerance change as machine oil temperature increases. Swiss Silver can be used with high-pressure delivery systems.