Drawworks, L.p    Boling, TX 77420
May 09, 2012 With HPFAC High Pressure Fill-up and Circulation Tool, operators can fill-up, circulate, and take flow-back while casing is being run. Tool optimizes safety by eliminating need for personnel in derrick during operations. HPFAC tool can be activated at control panel located on rig floor or remotely by driller. Should casing pressure rise above pre-set limit, tool will set automatically without human intervention.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Apr 23, 2012 Designed to generate small, manageable chips, CoroDrill® 861 drills combine Advanced Chip Management flute geometry, point geometry that helps reduce thrust forces, and double-offset margin geometry that lends to stability. Consistent edge preparation protects cutting edge from premature chipping and flaking. Able to produce accurate, deep holes to depths of 12-30 x drill diameter without pecking, drills can achieve IT8-IT9 hole tolerance when used with suitable high-precision chuck.

Baker Hughes, Inc. (BHI)    Houston, TX 77210
Mar 06, 2012 Able to drill vertical, curve, and horizontal sections in one run, AutoTrak Curve(TM) maximizes pay zones and minimizes number of trips. Closed-loop drilling system takes commands from surface to place wellbore in desired direction and inclination. Combining bottomhole assembly and drill bit, system achieves build rates of more than 15°/100 ft. Tolerant to presence of lost circulation material in mud system, AutoTrak Curve does not require special pressure drop between pipe ID and annulus to operate.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Feb 24, 2012 Designed for intermediate hole-tolerance area of IT9-IT10, CoroDrill 870 can be tailored to optimize applications through diameter range, steps, and length possibilities. Secure interface between drill body and tip ensures precision, while quick tip change helps maximize active machining time. Drill is available in 0.472-0.826 in. diameter range and lengths 3x and 5x hole diameter as standard.

Walter USA, Inc.    Waukesha, WI 53188
Feb 22, 2012 Characterized by parabolic flute profile, Walter Titex UFL® A1549TFP employs helix angle of 40°, optimizing rigidity. In many applications, drilling to depth of 10-12 x D without pecking is possible. Drill's HSS-E 5% cobalt content substrate provides heat resistance, while TiAIN tip coating boosts cutting parameters and tool life, and U form point geometry promotes chip formation. Available in 1-12 mm diameters, drill is suitable for all ISO material groups.

BIG Kaiser Precision Tooling, Inc.    Hoffman Estates, IL 60192
Feb 06, 2012 Featuring 137° point angle, Power-Phoenix Drills are designed for deep hole applications in steel, stainless steel, cast iron, aluminum, and titanium. Unique point grind ensures consistent chip formation, while polished flutes allow for rapid chip evacuation. Available in 1.0-12.7 mm diameters for 16 x D version and 2.0-10.0 mm diameters for 20 x D, 25 x D, and 30 x D versions, drills have wear-resistant Helica coating and through-coolant capability with coolant pressures down to 290 psi.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Jan 26, 2012 Used for steel drilling, CoroDrill® 860 comes in lengths 3-8xD and offers optimized chip evacuation control. Design accommodates conventional drilling, chamfered holes, inclined surfaces, cross holes, stack drilling, and convex/concave surfaces. When using high cutting data in long and short chipping materials, drill provides consistently problem-free drilling. Geometry, combined with flute shape, provides cutting edge shape for effective clearance of chip.

Walter USA, Inc.    Waukesha, WI 53188
Jan 11, 2012 Able to handle ISO-P, M, K, and N material groups, Walter Titex Xotreme M, DM8, and DM12 respectively cover drilling depths up to 5 x D, 8 x D, and 12 x D. Each solid carbide drill, available in diameters from 2-2.95 mm, has AlTiN-based coating for optimal cutting performance and tool life. Point geometry ensures precise positioning on entry, while internal cooling and polished flutes with specialized profiles optimize removal of heat and chips.

Walter USA, Inc.    Waukesha, WI 53188
Dec 01, 2011 Offered as special tool with diameters from 5-12 mm dia, Walter Titex XD70 can produce holes up to 70xD in one operation and does not require pecking. Cooling is provided via internal coolant channels, and no special coolant equipment, such as an external high-pressure system, is required. Standard cooling unit, such as those available with any machining center, is sufficient. Respectively, TTP and XPL tip coatings are available for steel and cast iron workpiece materials.

Walter USA, Inc.    Waukesha, WI 53188
Nov 16, 2011 Walter Valenite Xtraotec® insert drills come in diameters as small as 0.531 in., which are suitable for depths up to 5xD and equipped with size 1 inserts. Also available, cartridge format drills cover 2.35-4.70 in. dia range. Standard version features 3.15 in. dia with 3xD depth, while 4.70 in. dia and 5xD depth model can be ordered. Hole diameter can be finely adjusted to 0.024 in. on outer cartridge, and center cartridge comes with heavy-duty PVD-coated Tigerotec® cutting tool material.

Walter USA, Inc.    Waukesha, WI 53188
Oct 19, 2011 Featuring 4-margin design, 140° point angle, and L/D ratio of 3 x D, short version of Titex X•treme Drill is suitable for drilling angled entry/exit surfaces, convex workpiece surfaces, and cross holes. Internal coolant supply and aluminum chromium nitride-based XPL coating maximize tool life. Available from 1/8-¾ in. with cylindrical or whistle notch shank, drill is suitable for general machine construction and vehicle manufacturing as well as energy industry and die and mold industry.

Widia Inc.,    Latrobe, PA 15650
Oct 14, 2011 Featuring advanced VDS point geometry, VariDrill(TM) minimizes chipping on cutting edge and delivers extended tool life across range of materials, including steels, stainless steels, cast irons, non-ferrous materials, and high-temperature alloys. Its point and flute design enables chips to roll smoothly, minimizing friction, heat, jamming, and scratching. Available in 3XD, 5XD, and 8XD lengths as well as coolant-through and solid options, VariDrill provides optimum hole finish.

Baker Hughes, Inc. (BHI)    Houston, TX 77210
Oct 13, 2011 Installed and released prior to cement job, TORXS(TM) Expandable Liner Hanger System eliminates risk of running tools becoming fixed in place during cementing, requiring fishing or well abandonment. System enables seamless 1-trip, 2-stage hanger and packer setting for cemented liner applications. Advanced torsion capability allows casing to be worked to depth in challenging zones, and there is no need to add retarders that compromise cement formulation or extend cement pumping time.

OSG Tap & Die, Inc.    Glendale Heights, IL 60139
Oct 04, 2011 In addition to coolant-through capabilities, HY-PRO® CARB 3D and 5D Drill Series feature point and flute geometry that reduce thrust forces and chip size. Applied multi-layered TiAlN coating resists thermo-cracking from heat, improving wear resistance, and overall design fosters achievement of higher feeds and metal removal rates. Common DIN shank sizes promote rigidity while reducing number of tool holders required to accommodate them.

Walter USA, Inc.    Waukesha, WI 53188
Sep 08, 2011 Non-coolant thru versions of Titex X-treme(TM) solid carbide high-performance drills are available from 1/8-¾ in. dia and can be used with all common materials. Featuring 4-margins design that promotes stability relative to workpiece, drills maintain position at point of entrance or exit as well as when machining inclined surfaces. Additional features include aluminum chromium nitride-based XPL coating, 140° point angle, and cylindrical shank or whistle-notch shank.

CS Unitec, Inc.    Norwalk, CT 06850
Jun 14, 2011 Designed with horizontal motor mount, MAB 150 stands 7 in. tall and weighs 24 lb. It has 1 in. max drill depth with annular cutters in structural steel and other metals and is powered by 9.25 A, 110 V double-insulated motor with no-load speed of 400 rpm. Able to accept cutters with ¾ in. Weldon shank, portable drilling machine integrates automatic cooling/lubrication system, dual-coil magnet with holding strength of up to 2,640 lb, and left- or right-mounted advancing lever.

Torchmate    Reno, NV 89502
May 02, 2011 Supplied with software that is compatible with CAD/CAM design programs, 2X2 CNC Prototyping System cuts, drills, engraves, and can be used as router or plasma cutter. Machine's repeatability allows users to design part once and manufacture as many as needed. Basic package includes 2-axis machine, 2x2 Driver Software, relay to turn plasma torch or other closed circuit tool on and off, mounting plate, and basic cutting table.

Seco Tools Inc    Troy, MI 48083
Apr 11, 2011 Feedmax(TM) -N solid carbide drills, suited for drilling in aluminum and non-ferrous materials, feature low-silicon coating that suits machining of aluminum with less than 10% silicone, as well as brass, zinc, and magnesium. Tools have conical front clearance with 12° relief angle and 140° point angle, with narrow land margins to minimize friction and buildup of material on edges. They are available in diameters ranging from 0.1-0.551 in. and have 3xD drilling depth.

Seco Tools Inc    Troy, MI 48083
Mar 31, 2011 Available in diameters from 4-10 mm, Feedmax(TM) SD230A features 4-facet point geometry that provides optimal centering capability, with primary and secondary relief angles and point angle of 136°. Four land margins provide stability and maximize hole quality. Featuring low-friction, TiAIN + TiN coating, drill is suited for applications found in automotive, oil and gas, mold and die, medical, and general engineering industries.

Widia Inc.,    Latrobe, PA 15650
Mar 30, 2011 Available with 15XD, 20XD, 25XD, and 30XD length ratios, WIDIA-Rubig(TM) deep-hole drills come in 3.0-13.0 mm diameters and do not require special drivers or guide bushings. Products can also be used in machining centers and are engineered to enhance material removal rate, hole quality, and cycle times. With 132° cone-point geometry, drills provide thrust and centering ability that lend to hole quality. Also, 4-margin design improves stability in cut.