Esco Tool    Medfield, MA 02052
Apr 18, 2012 Esco Electric Wart MILLHOG® performs any angle of end prep and bevel, face, and bore simultaneously to produce clean, smooth, and square end preps. Designed for for applications where compressed air is not available, tool features Metalbo® 14 A electric grinder motor and gear reduction mechanism that produce variable speeds from 100-200 rpm. Portable tool is able to machine highly alloyed stainless steel pipe and tube from 3/4 in. ID to 4½ in. OD without requiring cutting oils.

Boart Longyear    Stone Mountain, GA 30086
Mar 15, 2012 Along with cutting matrix that enables penetration of hard rock formations in extreme conditions, 10UMX(TM) features Stage(TM) waterway design. Geometry of windows sustains integrity of bit through its entire life, allowing for variety of crown heights. Twin-Taper(TM) design improves surface flushing, forcing debris through windows while keeping bit face clear and reinforcing inner diameter. Razorcut(TM) protrusion arrangement on face of bit promotes tracking and balance in hole when drilling begins.

Thomas & Betts Corp.    Memphis, TN 38125
Dec 15, 2011 Providing couplings, adapters, reamers, and plugs, Carlon® PVC Conduit Repair System facilitates and accelerates repair of broken polyvinylchloride (PVC) conduit. Design lets contractors maintain conduit ID, reducing repair time to less than 2 min. Available in sizes from ½-2 in., system eliminates task of chipping away and re-pouring concrete around conduit. Included nonmetallic couplings, adapters, and plugs will not rust or corrode.

Rohrback Cosasco Systems    Santa Fe Springs, CA 90670
May 09, 2011 Available with pneumatic or electric drive options, COSASCO® Re-Facer Tool can repair corroded access fittings in pipelines under full operating pressure. Portable unit cuts and bevels surface area of fittings up to 0.020 in., including carbon steel and Hastelloy materials. Tool features feed rate of .0031 in. per trip, cutting speed of 30 sfpm, and cutting depths of 0.005, 0.010, and 0.020 in.

Boart Longyear    Stone Mountain, GA 30086
Mar 10, 2011 Comprising underground rock drill and blast rods and bits, Robust Standard Thread (RST(TM)) Series enhances impact efficiency, accelerates penetration, and lessenes hole deviation. Rods incorporate cross-sectional transition area that increases bending strength, while extended bit skirt reduces likelihood of rod tip-off events and downtime. Also, interchangeability with standard threaded rods and bits promote in-field flexibility.

Boart Longyear    Stone Mountain, GA 30086
Mar 09, 2011 Lightning Rod(TM) Series male and female rods have diameter range of 33-60 mm and lengths ranging from 8-14 ft. Male and female ends of products are wear-resistant and allow for automated subtractions and additions to drill string. Featuring mid-body steel design that offers efficient energy transfer, and which is optimized for air flushing, units are suited for various types of surface drill and blast applications.

Boart Longyear    Stone Mountain, GA 30086
Mar 09, 2011 Impregnating large synthetic diamonds within metallurgical formula, Ultramatrix(TM) Coring Bits create crown matrix that maximizes bit life and penetration capabilities. Razorcut(TM) face design optimizes tracking and balance in hole, while advanced Stage(TM) waterway design allows crown heights up to 25 mm. Twin-Taper(TM) windows optimize surface flushing, forcing debris through windows while keeping bit face clear and reinforcing inner diameter.

Seco Tools Inc    Troy, MI 48083
Nov 23, 2010 Developed for finish turning of nickel-based super alloys, CBN 170 grade is optimized for toughness and wear-resistance that can help increase tool life and cutting speed. It incorporates whisker ceramic binder and satisfies surface finish, tolerance, and length of cut requirements found in finishing operations. Designed for continuous cutting applications, product can achieve depths of cut up to 0.020 in. at cutting speeds from 900-1,300 sfpm.

Bondhus Corp.    Monticello, MN 55362 9347
Nov 10, 2010 Available in molded plastic carrying cases, high performance socket bits feature proprietary ProGuard finish and are constructed to survive tough work environments. Protanium steel construction provides strength, and design allows bit to flex instead of break when high torque levels are applied. Range of inch and metric, chamfered hex, ballpoint, and star tipped tools are available.

Bosch Power Tools & Accessories    Mt. Prospect, IL 60056
Oct 20, 2010 Available in SDS-max®, SDS-plus®, and Spline versions in various sizes, SpeedX series starts holes precisely via centric active tip and accelerates job initiation with inclined side cutters. Shortened head design and size of dust clearing channels enhance performance as holes get deeper. While wear mark is located at tip for precision anchoring applications, flutes reduce vibration and friction as holes get deeper by clearing debris.

Bosch Power Tools & Accessories    Mt. Prospect, IL 60056
Jul 01, 2010 Speed-X Hammer Carbide features centric carbide tip, side cutters that power their way into concrete, as well as head design and dust clearing channels that allow it to perform better as holes get deeper. Flutes minimize vibration in deep drilling, while vacuum-optimized brazing and heat treatment of carbide tip provide resistance to impact and thermal stresses. Wear mark on carbide tip alerts users when tip is worn and bit will stop precision anchoring at start of drilling.

PB Swiss Tools    Gainesville, GA 30501
Jun 07, 2010 Made from spring steel alloy with precision heat treatment, PrecisionBit® Series fits perfectly into screw and will not slip out during tightening and loosening. Units are available in variety of styles, including standard C6 bits and E6 power tool bits, in regular and long versions for wide selection of screw profiles. Colored nanotech coating not only enables users to differentiate between sizes, but also protects bits against rust.

Ideal Industries, Inc.    Sycamore, IL 60178
May 19, 2010 Double-fluted step drill bits feature ¼ in. hex shank, as well as aggressive split point tip that prevents skidding across surface and eliminates need to make pilot hole or punch. Each 1/16 in. multi-diameter step is radius-blended to smoothly transition from one step to next. Bits also have double-fluted design with secondary cutting edge to minimize vibration. Manufactured with double-tempered high-speed steel, they are available in 1/8 to 1/2, 1/4 to 7/8, and 1/4 to 1 1/8 in. sizes.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Apr 12, 2010 Offered in dia of 0.157-0.500 in., CoroDrill® 854 and CoroDrill® 856 are designed to withstand carbon fiber reinforced plastics and aluminum stacks in aerospace applications. Suited for high fiber content materials, model 854 addresses splintering or fraying problems, while model 856 eliminates delamination in resin-rich materials. Available in standard N20C solid carbide versions with diamond coating, both products help eliminate burrs and enhance surface finish.

GoldEdge Steel Solutions, Inc.    New Bethlehem, PA 16242
Mar 30, 2010 Manufactured using patented cryogenic treatment process that alters steel's molecular structure, ultra-durable GoldEdge® drill bits are designed to handle demanding jobs in construction, maintenance, and metal working industries. They feature 135° split point design that eliminates need for center punching, and 3-flat shank that eliminates chuck slippage, making it ideal for use in hand-held drills.

Bosch Power Tools & Accessories    Mt. Prospect, IL 60056
Mar 18, 2010 Nailkiller(TM) Auger Bit features reinforced tip that pushes hidden nails to side when it makes contact. Product's dual cutting edges enable it to slice through hidden fasteners twice per revolution. Dual-reamer-edge design prevents splinters from piercing electrical wire housings and wood fragments from clogging conduit or water pipes with narrow IDs. Bits use 7/16 in. shank with power groove, which fits ½ in. corded drill, and are available with 7½-24 in. lengths and ¼-1½ in. dia.

Climax Portable Machine Tools Inc.    Newberg, OR 97132
Mar 05, 2010 Used for in-situ repair and on-site machining of flange surfaces, FF6200/FF7200/FF8200 let users adjust feed rate while machine is running and without reaching into it. Feed rate is infinitely variable from 0.002-0.035 in./rev, and heavy-duty, construction-grade bearings provide rigid performance throughout entire machining range. Turning arm and tool head rotate full 360°, creating variety of chamfers, o-ring grooves, and other angular surfaces as well as generating phonographic finishes.

Bondhus Corp.    Monticello, MN 55362 9347
Jul 07, 2009 Made of Protanium® steel for strength, ProHold® Socket bits feature non-magnetic buttons on sides of each bit, which lock it securely into socket. Offered with ProGuard(TM) finish for corrosion protection, full range of inch, metric, and star tools are available.

DeWalt Industrial Tool Co.    Hampstead, MD 21074
Jun 25, 2009 Specifically designed for impact drivers, IMPACT READY(TM) Drill Bits feature one-piece shank design, which helps minimize occurrence of bit breakage. Tapered web design provides added strength in high-torque applications, while pilot point tip allows drilling process to begin rapidly upon contact with drilling surface for burr-free holes. Bits are suited for drilling holes into sheet metal, stainless steel, steel studs, and junction boxes.

Bondhus Corp.    Monticello, MN 55362 9347
Jun 10, 2009 Made from Protanium® steel, full range of inch, metric, and star tools is available with real 14K gold-plated finish and BriteGuard(TM) chrome-plated finish. Visually striking finish helps users locate tools and identify inch vs. metric models. All tools carry lifetime warranty.