Sandvik Coromant Co.    Fair Lawn, NJ 07410
Oct 10, 2012 Able to be tailored to optimize applications via diameter (0.472–1.020 in.), step, and length (3X, 5X, and 8X drill diameter) options, CoroDrill 870 features secure interface between drill body and tip that ensures reliability and precision. Tip change procedure helps maximize active machining time, while cutting edge geometries and grades increase penetration rates, provide safe cutting process, help maintain chip control, and promote extended tool life.

Walter USA, Inc.    Waukesha, WI 53188
Oct 04, 2012 Xtra•tec® Insert Drills are available with Tiger•tec® Silver aluminum oxide coating, which promotes tool life and process reliability in demanding drilling applications. Combining high temperature wear resistance and toughness, coating is available with several insert materials. Cutting materials WKP25S and WKP35S suit all cast iron and steel materials. When machining ISO-P, ISO-M, or ISO-S materials, PVD-coated center indexable insert made of cutting tool material WXP40 is available.

Walter USA, Inc.    Waukesha, WI 53188
Aug 21, 2012 Indexable grooving and cutoff inserts are available with Tigerotec® Silver PVD aluminum oxide coating, which offers high-temperature wear resistance to promote tool life. Optimized surface structure lowers friction on cutting surface; sharp, defined cutting edges can be achieved due to coating's thinness; and smooth surface helps prevent build-up on cutting edge while promoting process reliability. Four grades - WSM13S, WSM23S, WSM33S, and WSM43S - accommodate range of applications.

Klein Tools, Inc.    Lincolnshire, IL 60069
Aug 15, 2012 Conduit reaming drill head (Cat No. 85091) reduces time required for commercial electricians to ream and install conduit runs. Fitting into power drill chucks and quick release adapters, precision engineered replaceable blade reams ½, ¾, and 1 in. conduit using standard power tool. This U.S. manufactured tool, designed to minimize wrist strain experienced during extended conduit runs, includes replaceable No. 2 square recess bit for installing conduit fittings.

Walter USA, Inc.    Waukesha, WI 53188
Jul 11, 2012 Walter Titex Xotreme Inox, designed to work with stainless steel and other high-alloy ISO M materials, features multilayer TiAlN tip coating that maximizes tool life. Coordinated margins help minimize friction against hole wall, while internal coolant supply helps manage operating temperature. Design of main cutting edges and flute profile optimize stability. Available in 1/8 to ¾ in. dia sizes, drill is suitable for use in aerospace, chemical, and medical device industries.

General Tools & Instruments    New York, NY 10013
Jul 10, 2012 With addition of power drill, E-Z Pro Deluxe Doweling Jig Kit lets users produce edge-to-edge, right angle corner, or right angle edge-to-surface dowel joints in ¼, 5/16, and 3/8 in. sizes. Aluminum jig is anodized in gold color to impede corrosion. Pointed notches on working edges of jig center drill bit automatically, while included wood dowels add mechanical strength to butt joints and keep miters lined up during clamping. All components come in self-contained, pre-molded storage box.

H. T. Mould Inc.    Montreal, QC h4r2k9
Jul 03, 2012 Designed to fit on any drill, Polish Boss utilizes air-filled rubber drum, which can be inflated with any pump to conform to convex or concave shapes, for use in tight spaces. Because air in drum absorbs heat, it extends life of belts. Tool polishes chrome, paint, stainless steel, aluminum, magnesium, plastic, and most finished surfaces with lambskin sleeves that fit snugly over drum. Available in 3 sizes, Polish Boss is suited for polishing motorcycles, cars, aircraft, or marine vessels.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
May 29, 2012 Featuring thin TiAlN coating that helps retain cutting edge geometry, CoroDrill 862 produces holes in steel, stainless steel, cast iron, and aluminum. Post treatment, combined with specially designed point geometry, minimizes thrust forces, while Advanced Chip Management flute geometry helps evacuate chips. Available in drill lengths of 8-12 x D, CoroDrill 862 achieves hole tolerance of IT8-IT9. Internal coolant holes deliver coolant directly to tip of drill, even at deep drilling depths.

Drawworks, L.p    Boling, TX 77420
May 09, 2012 With HPFAC High Pressure Fill-up and Circulation Tool, operators can fill-up, circulate, and take flow-back while casing is being run. Tool optimizes safety by eliminating need for personnel in derrick during operations. HPFAC tool can be activated at control panel located on rig floor or remotely by driller. Should casing pressure rise above pre-set limit, tool will set automatically without human intervention.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Apr 23, 2012 Designed to generate small, manageable chips, CoroDrill® 861 drills combine Advanced Chip Management flute geometry, point geometry that helps reduce thrust forces, and double-offset margin geometry that lends to stability. Consistent edge preparation protects cutting edge from premature chipping and flaking. Able to produce accurate, deep holes to depths of 12-30 x drill diameter without pecking, drills can achieve IT8-IT9 hole tolerance when used with suitable high-precision chuck.

Esco Tool    Medfield, MA 02052
Apr 18, 2012 Esco Electric Wart MILLHOG® performs any angle of end prep and bevel, face, and bore simultaneously to produce clean, smooth, and square end preps. Designed for for applications where compressed air is not available, tool features Metalbo® 14 A electric grinder motor and gear reduction mechanism that produce variable speeds from 100-200 rpm. Portable tool is able to machine highly alloyed stainless steel pipe and tube from 3/4 in. ID to 4½ in. OD without requiring cutting oils.

Boart Longyear    Stone Mountain, GA 30086
Mar 15, 2012 Along with cutting matrix that enables penetration of hard rock formations in extreme conditions, 10UMX(TM) features Stage(TM) waterway design. Geometry of windows sustains integrity of bit through its entire life, allowing for variety of crown heights. Twin-Taper(TM) design improves surface flushing, forcing debris through windows while keeping bit face clear and reinforcing inner diameter. Razorcut(TM) protrusion arrangement on face of bit promotes tracking and balance in hole when drilling begins.

Baker Hughes, Inc. (BHI)    Houston, TX 77210
Mar 06, 2012 Able to drill vertical, curve, and horizontal sections in one run, AutoTrak Curve(TM) maximizes pay zones and minimizes number of trips. Closed-loop drilling system takes commands from surface to place wellbore in desired direction and inclination. Combining bottomhole assembly and drill bit, system achieves build rates of more than 15°/100 ft. Tolerant to presence of lost circulation material in mud system, AutoTrak Curve does not require special pressure drop between pipe ID and annulus to operate.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Feb 24, 2012 Designed for intermediate hole-tolerance area of IT9-IT10, CoroDrill 870 can be tailored to optimize applications through diameter range, steps, and length possibilities. Secure interface between drill body and tip ensures precision, while quick tip change helps maximize active machining time. Drill is available in 0.472-0.826 in. diameter range and lengths 3x and 5x hole diameter as standard.

Walter USA, Inc.    Waukesha, WI 53188
Feb 22, 2012 Characterized by parabolic flute profile, Walter Titex UFL® A1549TFP employs helix angle of 40°, optimizing rigidity. In many applications, drilling to depth of 10-12 x D without pecking is possible. Drill's HSS-E 5% cobalt content substrate provides heat resistance, while TiAIN tip coating boosts cutting parameters and tool life, and U form point geometry promotes chip formation. Available in 1-12 mm diameters, drill is suitable for all ISO material groups.

BIG Kaiser Precision Tooling, Inc.    Hoffman Estates, IL 60192
Feb 06, 2012 Featuring 137° point angle, Power-Phoenix Drills are designed for deep hole applications in steel, stainless steel, cast iron, aluminum, and titanium. Unique point grind ensures consistent chip formation, while polished flutes allow for rapid chip evacuation. Available in 1.0-12.7 mm diameters for 16 x D version and 2.0-10.0 mm diameters for 20 x D, 25 x D, and 30 x D versions, drills have wear-resistant Helica coating and through-coolant capability with coolant pressures down to 290 psi.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Jan 26, 2012 Used for steel drilling, CoroDrill® 860 comes in lengths 3-8xD and offers optimized chip evacuation control. Design accommodates conventional drilling, chamfered holes, inclined surfaces, cross holes, stack drilling, and convex/concave surfaces. When using high cutting data in long and short chipping materials, drill provides consistently problem-free drilling. Geometry, combined with flute shape, provides cutting edge shape for effective clearance of chip.

Walter USA, Inc.    Waukesha, WI 53188
Jan 11, 2012 Able to handle ISO-P, M, K, and N material groups, Walter Titex Xotreme M, DM8, and DM12 respectively cover drilling depths up to 5 x D, 8 x D, and 12 x D. Each solid carbide drill, available in diameters from 2-2.95 mm, has AlTiN-based coating for optimal cutting performance and tool life. Point geometry ensures precise positioning on entry, while internal cooling and polished flutes with specialized profiles optimize removal of heat and chips.

Thomas & Betts Corp.    Memphis, TN 38125
Dec 15, 2011 Providing couplings, adapters, reamers, and plugs, Carlon® PVC Conduit Repair System facilitates and accelerates repair of broken polyvinylchloride (PVC) conduit. Design lets contractors maintain conduit ID, reducing repair time to less than 2 min. Available in sizes from ½-2 in., system eliminates task of chipping away and re-pouring concrete around conduit. Included nonmetallic couplings, adapters, and plugs will not rust or corrode.

Walter USA, Inc.    Waukesha, WI 53188
Dec 01, 2011 Offered as special tool with diameters from 5-12 mm dia, Walter Titex XD70 can produce holes up to 70xD in one operation and does not require pecking. Cooling is provided via internal coolant channels, and no special coolant equipment, such as an external high-pressure system, is required. Standard cooling unit, such as those available with any machining center, is sufficient. Respectively, TTP and XPL tip coatings are available for steel and cast iron workpiece materials.