Drilling Machines & Tools

Related Categories
Machinery & Machining Tools

Insert Drills offer optimized clamping system, cutting material.

March 18, 2015

Featuring Walter Capto™ clamping system and indexable inserts with Tiger·tec Silver® cutting tool material, 16–45 mm dia Xtra·tec® Insert Drills can be used on materials from steel and cast iron to stainless and difficult-to-cut materials. Drills offer depth of cut of 3xD and can handle chain drilling, sloping, and convex surfaces. Indexable inserts comes in 3 geometries and 4 grades and have 4 cutting edges. Ground indexable inserts are also fitted with wiper edge for optimal finish. Read More

Machinery & Machining Tools

Solid Carbide Pilot Drill enhances deep hole productivity.

February 25, 2015

Used for drilling depths from approximately 2 x D, X•treme Pilot 180 comes in 1/8–7/8 in. dia, features internal cooling (emulsion or oil), and supports use with coolant pressures as low as 145 psi. Point angle is 180°, and corner protection chamfer maximizes reliability. Along with 4 margins for optimum alignment, features include TFT coating for protection against wear. Drill can be used for cross holes, spot-facing inclined or convex surfaces, and counterboring drilled holes. Read More

Machinery & Machining Tools

Micro Drill accelerates starter hole creation in wire EDM.

February 25, 2015

With its flute- and cutting-edge geometry, Sphinx micro deep-hole drill helps conserve time during creation of wire EDM starter holes. Functionality replaces process of plunge EDM to establish starter hole, and construction of carbide with abrasion-resistant coating promotes efficacy during use on high-strength alloyed tool steels. Holes with length/diameter ratio of up to 80 x Ø are possible in range of Ø.25–1.50 mm in steps of .1 mm for hole depths up to 20/40/60/80 x Ø. Read More

Machinery & Machining Tools

Rig-Mounted Core Drill offers multi-speed operation.

January 27, 2015

Used for drilling up to 14 in. dia holes in concrete, reinforced concrete, asphalt, and natural stone, 77 lb EBM 352/3 PSA employs 20 A motor and rugged gearbox with drilling speeds of 230, 500, and 1,030 rpm. Internal oil pump lubricates gearbox and shaft for extended life. Along with soft start and overload protection, features include mechanical slip clutch that provides protection in case of jamming. Screw jack for bracing is also included along with 39 in. tall anchor stand. Read More

Machinery & Machining Tools

Solid Carbide Drill overcomes deep-hole drilling problems.

January 15, 2015

Suited for applications up to 8xD, TiAlN-coated R459 drills such materials as steel, stainless steel, cast iron, copper, and aluminum. Continuously Thinned Web geometry maximizes flute volume and cross sectional strength, outer corner design protects against wear and chipping, and 140º point angle facilitates centering and reduces thrust requirements. While consistent edge preparation protects against premature chipping and flaking, internal coolant holes help minimize machine downtime. Read More

Machinery & Machining Tools

Solid Carbide Drill addresses small lot production needs.

January 8, 2015

Available in 0.12–0.63 in. diameters for everyday machining applications involving older machines, small quantities, or frequent workpiece changes, DC150 can be universally used for all materials and in all industries (especially general machining). Respectively featuring external and internal cooling, 3xD and 5xD variants are both available in cylindrical shank (DIN 6535 HA) or Whistle Notch shank (DIN 6535 HE) and may be used for material groups P, M, K, N, S, H, and O.
Read More

Portable Tools, Machinery & Machining Tools

Bit Inserts carry shock loads of impact drivers.

December 3, 2014

Constructed using shock-resistant tool steel and induction heat treatment that allows differential hardening of shank body, Tensor® Bits Series can withstand impact shock loads generated by tip interface, with screw head farther down shank and away from head. Shaped shank bit inserts leverage flexural properties of steel itself to transfer load from tip to shaft, minimizing risk of bit faces shearing off and extending bit life. Read More

Portable Tools, Machinery & Machining Tools

Portable Magnetic Drill features multi-axis positioning.

October 23, 2014

Used for job site drilling, boring, and slotting applications, MAB 800 KTS features infinitely variable torque control, servo-assisted drilling, 10 in. stroke, and full-wave electronics. Multi-axis positioning capability lets drill be adjusted up to 2 5/32 in. forward/backward and up to 4 ¾ in. left/right after magnet adheres to surface. In addition to cutting holes up to 2 3/8” dia, capabilities include twist drilling up to 1 in. dia. and tapping up to 1 1/8 in. dia. Read More

Mechanical Components & Assemblies, Machinery & Machining Tools, Services

Deep Hole Drill produces close tolerance holes. .

September 25, 2014

Suitable for diameters from 0.614–2.559 in. and tolerance demands of IT 9, CoroDrill® 808 features optimized pad design for good hole finish, unique edge preparation for chip breaking, and reinforced periphery insert corner for added security. Drill is equipped with fully traceable dot matrix. Two-dimensional patterned array is used for storage and display of various types of information, such as measurement protocol, which includes data on diameter and run out of drill. Read More

Machinery & Machining Tools

Solid Carbide Drills deliver performance, stability, reliability.

September 11, 2014

Supplied in 16xD and 20xD sizes and suited for use on ISO-P and ISO-K materials, DC170 internally cooled drill features land design that orients margins radially and copper-color finish (DPP Coating). Lands have shallow cooling grooves at drill end, and 8 visible cooling grooves can be used as scale for regrinding. Coolant flow encompasses entire drill point, optimizing cooling while also inhibiting chip packing. Amount of material behind cutting edge enhances sturdiness. Read More

Machinery & Machining Tools, Services

Core Drill creates holes from 1/4 to 2 5/8 in. dia.

July 23, 2014

Weighing 7 lb, END 1550 P Wet Diamond Core Drill creates holes in natural stone, tiles, porcelain, stoneware, and glass without shock, dust, or vibration. Unit is powered by 13 A variable-speed motor that operates with no load speed of 1,800–4,400 rpm. For corrosion-free wet operation, drill features integrated water supply with flow control and stainless steel spindle. Changing drill bits and removing center core is accomplished via standard quick-lock adapter or 5/8 in. x 11 UNC threads. Read More

Material Handling & Storage, Machinery & Machining Tools

Plastic Case keeps drill bits safe and ready for use.

May 28, 2014

Made of shock-resistant polyethylene plastic materials, bright orange-colored Walter Drill Bit Carrying Case helps protect Walter drill bits products from water, rust, oil, grease, and other contaminants. Closed, quick-release belt clip provides mobile end-users with practical means to realistically work with 29-piece drill bit set. Read More

Machinery & Machining Tools, Construction Equipment & Supplies

Rock Drill reduces operator exposure to noise and vibration.

May 23, 2014

Designed to suppress noise and vibration, S250-M3 improves drilling production while decreasing fatigue regarding operators' ears, hands, and feet. Main airflow cylinder channel and exhaust allow efficient actuation of drill, and design drives more energy to face of rock. Vibration level also helps reduce components wear, promoting extended operation. There are 3 primary variations — jackleg, stoper, and sinker — to match specific needs, and 22 and 25 mm drill hex chuck ends are available. Read More

Portable Tools, Machinery & Machining Tools, Mining, Oil Drilling & Refining

DTH Hammers and Bits are designed for down-the-hole drilling.

May 8, 2014

Designed to increase productivity in reverse circulation (RC) drilling and conventional down-the-hole (DTH) drilling, BLH™ series includes valved BLH5 and BLH3 hammers as well as valve-less BLH1. Bits are available to support all BLH hammers. BLH5 delivers balanced operation with minimized vibration as well as optimized productivity in various ground conditions, and BLH3 adds steel valve system. With minimal moving parts, BLH1 achieves balance between simplicity and performance. Read More

Machinery & Machining Tools

Solid Carbide Deep-Hole Drills reach depth of 50 x diameter.

May 7, 2014

With respective drill depths of 40xD and 50xD, Walter Titex X•treme D40 and D50 employ XD (extremely deep) technology which enables holes to be drilled in one operation, without pecking, in steel, cast iron, or non-ferrous metals. TiALN-tip coating promote service life, and other features include internal coolant channels for optimum heat dissipation and reliable chip evacuation. Latter is also supported by polished flutes, and 4 margins keep drill exactly on its intended course. Read More

Machinery & Machining Tools, Services

Solid Carbide Microdrill can serve diverse applications.

April 28, 2014

Built on KC7325™ solid carbide grade, GOdrill™ is designed for 0.0394–0.5 in. dia holes and works with multiple materials. Marginless design reduces friction and heat, and multilayer TiAlN-based coating allows for high-heat hardness. Second TiN top layer serves as visual wear indicator. Available in solid (flood coolant) or through-coolant options, drills also feature straight cutting lip with protection chamfer that ensures even distribution of cutting forces. Read More

Portable Tools, Machinery & Machining Tools, Construction Equipment & Supplies

Foundation Drilling Tools feature quick change holders.

April 1, 2014

In addition to quick-change tool holders and tools, KF Series includes duo-cut and single-cut wall cutters, welding bar tools and teeth, modular pilot drills, and modular pilot drill holders. Series covers majority of core barrel applications and is suitable for all foundation drilling conditions, especially deep foundation of large-diameter bore holes. Also, tapered seating design provides strong seating area and enables easy removal of tool. Read More

Machinery & Machining Tools

Drilling Unit mounts to robots for complex applications.

March 19, 2014

Measuring 15.5 x 3.9 x 8.3 in., SSV2 Selfeeder™ Servo Series provides spindle speeds from 390–200,000 rpm, supporting small diameter drilling in aluminum, cast iron, and steel. Combination of high-power motor and compact size makes SSV2 suitable for automated robot applications in aerospace industry and applications where hard mounted drill does not apply. Read More

Machinery & Machining Tools

Solid-Carbide Drill produces burr-free holes in CFRP-metal stacks.

March 14, 2014

Used for drilling composite fiber-reinforced polymer (CFRP)-metal stacks in hole diameter ranges of 3/16–5/8 in., B55_DAL operates with standard through coolant, MQL, or dry. Double-angle point design lends to centering capability, while sharp edge cleanly cuts CFRPs in top layer of stacks and cleanly exits titanium or aluminum side. Stack drill can be applied in all combinations of stacks, and fine-grain solid-carbide Beyond™ KN15™ grade is polished for optimal chip evacuation.
Read More

Machinery & Machining Tools, Mining, Oil Drilling & Refining

Diamond Coring Drill Rig supports deep hole drilling.

March 11, 2014

Combining 110 kW power pack, 128 kN feed frame, rotation unit, foot clamp, and controller, Model LM110 provides high pullback force and fast rod-handling rate for maximum drilling productivity. Components can be interchanged to adapt to customer requirements as their needs change. For optimized safety, hands-free making or breaking of joints, and semi-autonomous drilling, Model LM110 can be outfitted with rod handler and Drill Control Interface™. Read More