Amada Cutting Technologies Inc.    La Mirada, CA 90638
Sep 11, 2008 Single pulse cutting machines PCASW430AX and PCSAW530AX are designed to minimize problems such as noise, vibration, and cutting resistance for optimal efficiency in metal bandsawing. While PCASW430AX and PCSAW530AX, respectively, cut material sizes up to 16 and 21 in., both machines are optimized for reductions in cutting noise, kerf loss, and material waste to promote safe and efficient working environment.

Tyrolit Schleifmittelwerke Swarovski K.G.      Austria
Sep 11, 2008 Providing more than 10 dBA noise reduction, SILENTIO resinoid-bonded, fiberglass-reinforced grinding wheel is suited for working on steel and SS to maximum speed of 80 m/sec, has damping feature for high run-out, and is available in 4 diameters in 115-230 mm range. Intended for machining SS at up to 80 m/sec, SUPER-THIN cut-off wheel is manufactured by using specially coated abrasive grain and fiberglass reinforcement.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Sep 10, 2008 WMX wiper insert combines main radius with multiple complementary radii and integrates chip-breaker geometry. This design widens feed rate and chip-breaking ranges. Designed for broad variety of applications, insert enables high quality surface to be achieved in finishing operations.

2L inc.    Hudson, MA 01749
Sep 10, 2008 Including selection of 5 styles of 2L's precision solid-carbide engraving tools, Engraving Tool Starter Kits help simplify engraving tool selection. Available for diameters of 1/8 and 3/16 in. in lengths of 2 in., each kit has conical ballnose and conical softer material engraving tools for use with aluminum, brass, and plastic. Kits also have engraving tools for steel, SS, and iron, such as tough tip and conical general purpose engraving tools and engraving mill-drill tool.

Matthews International Corp., Marking Products Div.    Pittsburgh, PA 15206 4407
Sep 10, 2008 With self-cleaning printhead, I-Mark(TM) C84e Continuous Ink-Jet marking system prints up to 4 lines of text from .05-.61 in. high at maximum production line speed of 1,050 fpm. It may be used to print expiration dates, batch codes, logos and bar codes on porous/non-porous materials. Unit has solvent pump and improved start-up/shut-down programs, flush routine that removes ink and flushes solvent to printhead nozzle, and vertical text positioning for fine adjustment of spacing between lines.

Rex-Cut Products, Inc.    Fall River, MA 02720
Sep 09, 2008 Rex-Cut® Megabrite T27 Finishing Flap Discs are offered in 3 grades including coarse, medium, and fine grits for cleaning, deburring, blending, and finishing stainless steel, aluminum, and other metals. Featuring smooth, controlled action, they are constructed with layers of non-woven synthetic fiber surface conditioning materials. Available in 4½ and 5 in. dia sizes with 7/8 in. holes or 5/8-11 adapters, with or without hubs, flap discs are rated for 13,300 rpm max.

Manncorp    Willow Grove, PA 19090
Sep 05, 2008 Suitable for prototyping, short runs, or full production, Economy Turnkey Line features 3 main components. MC384 pick-and-place machine, offering speeds of 4,000 cph, includes 128-lane feeder capacity and ability to mount 0201s, CFPs, and µBGAs in 14.5 x 13.4 in. placement area. Model 5500 Stencil Printer has independent, pressure-controlled dual squeegees and pneumatically controlled stencil frame. With 5 independent zones, CR5000 reflow oven attains lead-free-ideal temperatures to 300ºC.

Anver Corp. - Anver.Com    Hudson, MA 01749
Sep 05, 2008 Used for loading and unloading operations, VT Series lets one person handle four 5 gal pails (50 lb each) at once without manual lifting. Unit can be integrated with ceiling mounted gantry crane and is available with range of vacuum pad attachments. Along with 4 pliable bellows-style suction pads that provide soft touch and secure hold under vacuum, product features ergonomic handle with up/down controls that can be adjusted to match user's hand strength.

CS Unitec, Inc.    Norwalk, CT 06850
Sep 05, 2008 With blade stroke of 2 3/8 in., Model 5 1212 0050 will cut 24 in. dia pipe at 90° in one pass. Unit features 1.5 hp air motor that uses 51 cfm air volume at 90 psi air pressure. Certified to ATEX regulations EX 112 GcT5, saw can operate in hazardous atmospheres and environments classified as EX Zone 2. Portable tool uses range of heavy-duty blades from 8-37 in. long, which are available in HSS (M2) and HSS-SL with Molybdenum for cutting carbon steel, SS, and hard alloys.

Modern Process Equipment, Inc.    Chicago, IL 60623
Sep 05, 2008 Model IMD 99 Gum Recovery Gran-U-Lizer(TM) is specifically designed to flatten and striate candy-coated gum tablets for internal re-work and recycle. Special roll corrugations allow for high production rates and clean operation, in which hard candy coating is broken and separated from gum substrate. Thereafter, each component can be separated and re-introduced, at different phases, back into production process.

Manchester Tool & Die, Inc.    Manchester, IN 46962
Sep 05, 2008 With capacity of ¾ in. dia x .120 in. wall, 24014 High Pressure/High Thrust Groover operates by advancing and closing spinning head containing rolling or cutting tools over clamped tube. Depth of rolled or machine cut grooves can be changed, and design facilitates access to tooling as well as tool changes. In addition to 5 sec cycle time, machine features jaw opening of 1¼ in. and clamp force of 3 tons. It comes with 7½ hp spindle motor and variable speed control.

Bosch Power Tools & Accessories    Mt. Prospect, IL 60056
Sep 04, 2008 Utilizing Litheon(TM) battery technology, Brute Tough(TM) 18 and 14.4 V cordless drill/drivers and hammer drill/drivers feature 25+1 clutch and tight-gripping ½ in. metal chuck. Unibody motor construction, all-metal gear train, and DuraShield housing lend to durability, while ergonomics promote grip and minimize fatigue. Offered in same voltages, Compact Tough(TM) cordless drill/drivers offer maneuverable performance via ergonomic design, 20-position clutch, and ½ in. single sleeve chuck.

Applied Materials, Inc.    Santa Clara, CA 95054
Sep 03, 2008 Applied Endura® Extensa(TM) PVD1 is used for depositing critical barrier films for copper interconnects in sub-55 nm memory chips. Its titanium/titanium nitride (Ti/TiN) process technology enables diffusion barrier films with optimal step coverage and less than 3% film thickness non-uniformity across wafer. Dual-magnet PVD source with flux-shaping side electromagnets enables defectivity below 10 particles at greater than/equal to 0.12 µm.

Applied Materials, Inc.    Santa Clara, CA 95054
Sep 03, 2008 Optimized for throughput and MTBC ratings, Applied Producer® Etch system performs interconnect dielectric etch steps needed for production of Flash and DRAM memory chips. Reactor design promotes high-throughput, high-yield dielectric etch in DRAM and NAND Flash interconnect structures from 8X-4X nm technology nodes. System is suited for chip manufacturing applications such as low k deposition, strain engineering, litho-enabling films, thermal films, and high-temperature PECVD.

Star Micronics GB Limited    Melbourne   United Kingdom
Sep 02, 2008 Sliding-headstock, 7-axis CNC mill-turn centers manufacture simple to medium-complex parts up to 20 mm dia. Available with guide bush, SR-20J suits precision machining of long, slender components as well as short, complex parts. Model SR-20JN, used for complex machining of larger diameter components, does not have guide bush and minimizes material costs. Both machines feature 3.7 kW/10,000 rpm main spindle, 35 m/min linear axis rapids, and C-axis positioning of main/counter spindles.

Amada Wasino America, Inc.    Rolling Meadows, IL 60008
Sep 02, 2008 Featuring B-axis with 270° range of motion and capable of 5-face machining in one set-up, Mi8 is suited for manufacturing complex and multi-operation work pieces for industries that demand precision parts. Components include fixed station tools for turning, 20-station tool changer for rotary tools, as well as 8,000 rpm main turning and 20,000 rpm milling spindles. With integration of robot, machine can also perform unattended small production runs of carbon and copper electrodes.

Hilti Inc.    Tulsa, OK 74121
Sep 02, 2008 Suited for cutting pipe, strut, threaded rod, steel studs, and other miscellaneous steel, Hilti WSR 36-A can also be used for cutting wood with nails, wood beams, treated lumber, plywood, wood composites, or plastics. With 36 V 3.3 Ah CPC Li-Ion battery, it features Active Vibration Reduction technology that reduces vibration by up to two-thirds. Including ergonomic operating controls and comfortable handling, it maintains control when cutting overhead and in difficult to reach areas.

Sandvik Coromant Co.    Fair Lawn, NJ 07410
Sep 02, 2008 Suited for turning/milling applications, Coromant Capto® machine adapted clamping units (MACUs) promote flexible system changes while also channeling high-pressure coolant. Self-centering and balanced polygon coupling enables MACUs to operate in any situation, from low- to high-speed machines, without changing properties of balanced spindle. System covers all metal cutting operations, such as turning/machining centers and multi-task machines.

Guyson Corporation of U.S.A.    Saratoga Springs, NY 12866
Aug 28, 2008 Fitted with direct pressure media delivery module, Model 8-EP is suitable for processing components with large amount of surface area and for surface treatment operations such as descaling, etching, coating removal, and surface preparation. Consisting of cyclonic separator linked to ASME-certified pressure vessel, pressure-blast module is attached to rear of blast cabinet. Most types of dry blast media can be used, including plastic grit, glass beads, and fast-cutting mineral grit.

Primary Cutter, LLC/SUPERMILL    Berlin, CT 06037
Aug 28, 2008 With tool geometry specially designed for aluminum applications, SUPERMILL carbide end mill features sharp corner, full eccentric relief, and diamond like carbon coating for fast stock removal and long tool life. Available in 3 flute, variable pitch and with 45° helix angle, it is offered in 3/16 to 1 in. sizes, and Long and Extra Long in ¼ to 1 in., and is designed to meet demanding application requirements in aerospace and medical industries.