G2 Fuel Technologies    Tampa, FL 33646
Jan 14, 2011 Supporting uses from cleaning to lubricating, Bio-Blast(TM) is composed of additives and bio-solvents that provide penetrating catalyst that is non-staining to metals. Product works by driving out moisture, providing dielectric insulation in electrical equipment, and removing rust/dirt. Formulated to penetrate into tight areas and prevent corrosion, lubricant performs with capillary wetting action that reduces surface tension and frees up frozen parts.

Nye Lubricants, Inc.    Fairhaven, MA 02719
Dec 30, 2010 Using phenylmethyl silicone as base oil, NyoGel® 741A-RED soft grease is intended for light- to moderately loaded bearings and instruments. This red version of 741A has recommended service range of -65 to +200°C, making it suitable for low-temperature applications where little torque is available. Kinematic viscosity values are 27.8 cSt at 100°C and 71.2 cSt at 40°C, and viscosity index value is 404 as per ASTM D-2270. Respective flash and pour points are 275°C and -70°C.

Nye Lubricants, Inc.    Fairhaven, MA 02719
Dec 08, 2010 Consisting of 15% aqueous dispersion of PTFE, NyeFilm® 501F is applied in wet form, which then dries to surface. Product was developed to have controlled particle size distribution where no particles are greater than 10 microns, allowing for even distribution of PTFE. Environmentally safe, NyeFilm® 501F offers rub and abrasion resistance as well as chemical compatibility with all polymers.

Lubrication Engineers, Inc.    Fort Worth, TX 76107
Nov 10, 2010 Designed to help electric motor bearings run cooler and last longer, Monolec® Extend EM Grease (1282) increases motor efficiency by decreasing drag. It offers mechanical stability even in high-moisture environments and contains Monolec proprietary wear-reducing additive. Resistant to oxidation, NLGI grade 2 grease protects bearings against rust and corrosion and also resists water spray-off. It will not bleed into motor windings and maintains pumpability at low temperatures.

ZYP Coatings, Inc    Oak Ridge, TN 37830
Oct 27, 2010 Able to be used in temperatures from ambient to 1,000°C, Keralon-B is brushable lubricant/coating/paint based on organic Methylated Seed Oil and inorganic ceramic mixture of chemically-inert lubricating phases: Boron Nitride, Graphite, and Titanium Dioxide. It performs as oily mixture at room temperature and acts as dry film lubricant above 200°C. Solution is nonreactive/nonwetting with molten metals, glasses, and slags and prevents oxidation/rusting/galling/reactions while lubricating.

Hydrotex    Carrollton, TX 75006
Sep 16, 2010 Non-toxic, non-bioaccumulative, and chemically inert with low VOCs, Techni-Glide Lubricant contains microscopic poly-spheres that reduce surface contact, enabling smooth cable pulling, even under high sidewall bearing pressures. After drying, there is no sticky residue and product remains slippery. Low aquatic toxicity makes Techni-Glide suitable for marine and port installations as well as any area concerned with ground water, soil, or water contamination.

Chemtronics, Inc.    Kennesaw, GA 30152
Aug 18, 2010 CircuitWorks® Boron Nitride Heat Sink Grease is thermally conductive grease, available in syringe dispenser for precision application. Engineered material provides optimal thermal conductivity for heat sinks with maximum electrical insulation. Throughout its rated thermal range of -99.4 to +392°F, silicone-free product will not harden or dry out.

Lincoln Industrial    St. Louis, MO 63120 1578
Aug 17, 2010 Designed for heavy-duty applications, 18 V PowerLuber features output-optimized motor and battery technologies that unite to promote run time. Dual-speed transmission provides high-volume grease flow option. Along with torque-optimized motor, 120 V corded PowerLuber features variable-speed trigger and 2-speed transmission for precise flow control. Both guns, in addition to balanced design, have composite body as well as metal gear and pump housing.

CIMCOOL®    Cincinnati, OH Oh. 45209
Aug 04, 2010 Designed for moderate to heavy-duty operations, CIMTECH 609® is suitable for use with most aluminum alloys, titanium, exotic alloys, cast iron, carbon steels, high-speed steel, high alloy steels, and stainless steels. Product offers drawability and biological protection for use in recirculating systems. With no smoke and minimal residue, low-misting fluid leaves no slippery film on parts, machinery, or floor. Corrosion inhibitors allow use on both ferrous and non-ferrous applications.

CIMCOOL®    Cincinnati, OH Oh. 45209
Aug 04, 2010 Featuring hybrid blend of patented and synthetic lubricants, CIMTECH 610® provides synergistic performance on difficult-to-machine ferrous and non-ferrous alloys without corrosion or stain. Product is suited for use on hard, brittle metals, such as inconel, titanium, stainless steel, aerospace alloys, and hardened steel. Formulated without chlorine, sulfur, or phosphorous EP lubricants, low-foaming fluid offers near neutral pH and corrosion control.

CRC Industries, Inc.    Warminster, PA 18974
Jul 26, 2010 Formulated to withstand extreme temperatures of -40 to 450°F, Syntha-Tech(TM) Lubricant w/PTFE penetrates into cracks and joints to lubricate and protect all exposed metals. Non-flammable, zero-VOC product utilizes PTFE additives to minimize surface contact, friction, and wear, extending equipment life. Available in 16 oz aerosol can, food-grade product is NSF H1 Registered for use in meat and poultry facilities.

Ultrachem Inc.    New Castle, DE 19720
Jun 25, 2010 Available for compressor, hydraulic, chain, gear, and multipurpose applications, Omnilube® food grade synthetic lubricants are suited for all food, beverage, pharmaceutical, and related industries. They meet all requirements of USDA, 21 CFR 178.3570, and conform to requirements of NSF. Also available in 12 oz aerosol spray cans, lubricants are formulated from high quality polyalphaolefin (PAO), polyalkylene glycol (PAG), ester, and mineral base oils, depending on application.

Sunnen Products Co.    St. Louis, MO 63143
Jun 16, 2010 Based on renewable vegetable formulation, SHO-500 cutting oil provides oxidation stability and is suited for honing applications where additives cannot be used, such as nuclear and some aerospace parts. Available in 5 gal pails, 55 gal drums, and 330 gal totes, oil can be used with conventional vitrified honing abrasives and metal-bond super abrasives.

ITW Rocol North America    Glenview, IL 60025
Jun 09, 2010 Made from naturally derived, vegetable-based oils, Rustlick PowerCool Green and PowerCool Green CF water-soluble oils are formulated to provide optimal lubricity and biostability in heavy-duty cutting and grinding applications. Products are safe for all metals and suited for light- to heavy-duty jobs. PowerCool Green contains chlorinated EP additives, while PowerCool Green CF contains non-chlorinated EP additives and is also recommended for use on titanium.

Alemite Corporation    Charlotte, NC 28226 3515
Jun 09, 2010 Operating at 7,500 psi, Pistol Grip Grease Gun includes dual leverage feature for operating in volume or pressure mode, ergonomic rugged cast handle, and universal follower for cartridge and bulk use. Gun delivers 1 oz of grease per 30 strokes and has cylinder capacity of 16 oz. Heavy-duty follower spring maintains prime.

Blaster Chemical Co.    Valley View, OH 44125
May 10, 2010 Containing sulfur, chlorine, wetting, and anti-weld agents, light-colored Cut 'N Cool is suited for stainless steel, carbon steel, aircraft steel, cast iron, aluminum, and other hard alloys. Product's petroleum base helps prevent rust on machinery, tooling, and materials. Formulated to meet stringent environmental regulations, Cut 'N Cool comes in recyclable aerosol package.

McLube Div., McGee Industries, Inc.    Aston, PA 19014
Apr 23, 2010 Water-based lubricant, intended for rubber, plastic, leather, and metal parts, suits automobile and transportation industry applications such as O-rings, seals, gaskets, and weather-stripping. Also used as insertion and assembly lubricant, product eliminates noises such as squeaks, rattles, squeals, and whines. It exhibits thermal as well as chemical stability and provides clear colorless film coating that will bond to applied surface. Inert nature lends to overall compatibility.

Lubrication Engineers, Inc.    Fort Worth, TX 76107
Apr 20, 2010 Battery Powered Clear Grease Gun features high-impact, fracture-resistant clear tube. Tube collars made of T6061 aircraft aluminum, and gun has maximum pressure of 8,500 psi, delivers up to 4.9 oz of grease per minute, and provides 19.2 volts of power. It comes with two 1,500-mAh rechargeable battery packs and 30-in. whip hose, as well as battery charger and hard plastic storage case. Cartridge holds 14.5 oz grease.

ITW Rocol North America    Glenview, IL 60025
Apr 16, 2010 Designed to stay where it is applied, Accu-Lube JL-12 opaque gel lubricant can be pumped or hand-applied directly to tube or bending mandrels, leaving clean coating on mandrel that will not build up over time. No cleaning is required before welding and lube can be easily cleaned before paint or plating.

CRC Industries, Inc.    Warminster, PA 18974
Mar 10, 2010 With ability to withstand extreme pressures, temperatures up to 650°F, water, and chemicals, CRC Quick Dry Moly Lube fills pores of metal surfaces to provide dirt repelling barrier that protects surfaces from pressure and friction. Available in 16 oz aerosol can (part #03043), EPA regulatory compliant solution does not contain any known Ozone Depleting Chemicals. It can be applied on gaskets, transfer belts, and conveyor belts.