AEMC Instruments    Foxborough, MA 02035
Jun 21, 2011 Powered by alkaline batteries, 4-channel Simple Logger® II Model ML914 includes 4 integral 6 in. MiniFlex® current probes. Line tracking is performed such that 64 samples over one line cycle are taken, and harmonic measurements are calculated from these 64 samples. Recorder stores TRMS at user programmable rates up to 8 times/sec. Through Bluetooth communication, data from instrument's internal memory can be transferred to computer for analysis.

AEMC Instruments    Foxborough, MA 02035
Jun 21, 2011 Water-resistant and IP65-rated, 4-channel Simple Logger® II Model AL834 features 4 integral current sensors, each measuring 24 in. long and capable of wrapping around 8 in. conductor. Selection of data storage modes, as well as data sampling rates is user programmable through DataView® software. Up to 1,000,000 measurements can be stored in internal nonvolatile memory. Powered by 4 C cell alkaline batteries, logger communicates to DataView software via Bluetooth technology.

Larson Electronics, LLC    Kemp, TX 75143
Jun 21, 2011 Incorporating water-cooled diesel engine and 10,000 W generator, Model HAL-WCDE-4X1000 provides lighting solution for areas up to 7 acres. Tower includes four Class 1, Division 2, 1,000 W metal halide lights that produce total of 440,000 lumens and are mounted atop telescoping boom, which can be extended to 30 ft in height. With fuel capacity of 15 gal, unit can run uninterrupted for up to 12 hours. Entire lighting package is mounted to 2-wheel trailer with 15 in. wheels and 2 in. ball hitch.

Allegro MicroSystems Inc.    Worcester, MA 01615
Jun 20, 2011 Suited for backlighting LCD monitors and TVs, A8516 WLED/RGB driver helps designers reduce component count by integrating boost controller to drive external MOSFET and 6 internal current sink channels capable of up to 80 mA each. Channels can be combined to achieve higher currents, and boost converter operates in constant frequency (programmable) current mode control. LED sink current is set by external R_ISET resistor, and PWM dimming allows control of LED currents.

Trek, Inc.    Medina, NY 14103 9710
Jun 20, 2011 With large signal bandwidth greater than 125 kHz (-3 dB) and small signal bandwidth greater than 200 kHz (-3 dB), Model PZD700A addresses need for capacitive load driving requirements. Design delivers DC stability and precise control of output voltages (DC or peak AC) in programmable ranges of 0 to ±700 V with output current range of 0 to ±100 mA (bipolar model); 0 to +1.4 kV with ±50 mA (unipolar model); and 0 to -1.4 kV with ±50 mA (unipolar model).

Crestron Electronics, Inc.    Rockleigh, NJ 07647
Jun 20, 2011 Channel selectable for 70 or 100 V, AMP Series is suited for lecture halls, restaurants, and conference rooms. At less than 11 in. deep, Models AMP 2210S and AMP-3210S offer 2 or 3 channels to drive 4 and 8 W speakers at 120 W and 210 W, respectively. At less than 15 in. deep, Models AMP-2210T and AMP-3210T deliver 2 or 3 channels for 210 W at 4 W, 120 W at 8 W, and 120 W at 70/100 V. Model AMP-2210HT offers full 210 W at 70 V. All fit in 1U rack and include auto power-down.

datakamp System    Buxtehude D - 21614  Germany
Jun 20, 2011 Based on MXM system connector, 70 x 70 mm Q7bd-GT40N features AMD Embedded G-Series platform that combines CPU and GPU into one embedded Accelerated Processing Unit (APU). Apart from DirectX-11 capable graphics, computation-intensive tasks can be transferred to GPU. By offloading from CPU, overall performance of APU can be increased. Unit provides functional requirements for embedded application, which includes PCIe, graphics, sound, mass storage, network, and multiple USB ports.

HASCO Hasenclever GmbH + Co KG    Ludenscheid D-58513  Germany
Jun 20, 2011 Able to withstand operating temperatures up to 180°C, Z13/... Series is designed primarily for precise guiding of ejector plates in injection molding tools, compression molds, and diecasting molds, and for guiding of mold plate assemblies. Guide ball bearings roll continuously in rotating ball tracks, virtually eliminating possibility of denting guide pillar. Installation of Z13/... Series in H7 drill holes is possible in tight spaces.

CamdenBoss Ltd    Mildenhall   United Kingdom
Jun 20, 2011 IR and vapor phase reflow solder compatible SMT LEDs indicators come in 0603/0605, 0805, and 1206 size packages that conform to EIA standards and are compatible with automated placement equipment. Depending on size, color options include red, amber, yellow, green, blue, white, and red/green. All offer 130° viewing angle, max forward current of 30 mA or 20 mA for blue lamps, 5 V max reverse voltage, and clear lenses. Parts include panel mount 514 23-LED series and open-ended 580 series.

Creform Corp.    Greer, SC 29652-0830
Jun 20, 2011 Custom built using 28 mm pipe and metal joints, Creform Cart enables one person to move heavy grinding wheels without aid of powered vehicle. Storage sections are adjustable to accommodate varying wheel widths, and angle of retaining supports allows wheels to be lifted in or out by hand or with lift assist device. Additional features include 4 in. urethane casters, 2 fixed and 2 with locking brakes, and abrasive-resistant UHMW polyethylene tubing on bottom support pipes.

TB Wood's, Inc.    Chambersburg, PA 17201
Jun 20, 2011 Suited for problem drives that require impact strength, Premium Banded V-Belts feature multiple layer tie band that provides lateral rigidity to prevent belts from turning over or coming off drive. Clutching non-rubber surfaced cover allows momentary slippage due to excessive overloads without burning belts up, while Kevlar or Aramid tensile cords yield maximum strength and virtually zero stretch. Curve design compensates for sidewall bulge, which occurs when belts bend around sheave.

ILLUMRA    Orem, UT 84058
Jun 20, 2011 Working with any Dawn/Dusk sensor, ILLUMRA CMR helps minimize energy consumption by shutting off lights during second half of every night. One device is installed per pole or fixture to shut off lights when not needed for maintaining safety lighting levels. CMR automatically synchronizes to existing dawn/dusk sensors, adapts to changing seasons, and limits peak demand inrush through sequenced start up. Applications include parking lots, parking garages, streetlights, and landscape lighting.

Solutionware Corp.    San Jose, CA 95129
Jun 20, 2011 Working within GeoPath and MazaCAM CAD/CAM software, Solid-Verify module helps users save time by verifying CNC programs on computer before putting them on machine. Integrated solution shows cuts, rapid crashes, tools and holders, differently shaped tools, and user-defined tools on computer before going to CNC. Simultaneously, unwanted rapid moves through part are identified on computer screen. Module was provides feature set commonly needed in solid-verification.

Solutionware Corp.    San Jose, CA 95129
Jun 20, 2011 Supporting entire range of machines from Mazak's first T1 model to Mazatrol SMART lathes and controls, MazaCAM Smart Edition converts between control generations, programs Mazatrol on computer, converts CAD files such as IGES and DXF to Mazatrol, and checks program before it goes out to shop floor. Additionally, software offers live-tooling support for multi-tasking mill-turn lathes, and enables users to send/receive files over Ethernet directly to CNC.

PCB Piezotronics Inc.    Depew, NY 14043 2495
Jun 20, 2011 Operating over 20 Hz to 20 kHz range, models 130E20, 130E21, and 130E22 have similar specifications but are respectively differentiated by BNC, 10-32, and SMB connectors. All models have electret designs and operate on free-field response type, which compensates for their own presence in sound field. Sensitivity is 45 mV/Pa, with noise dloor rating of 30 dBA, and sound pressure level measurement is rated up to 122 dB. TEDS v1.0 lets user locate specific microphone within large group.

PCB Piezotronics Inc.    Depew, NY 14043 2495
Jun 20, 2011 Series 4115K uses non-contact, rotary transformers for sending excitation voltage to and receiving measurement signals from strain gauge instrumented rotating sensor element. Flange and splined shaft design conforms to AND 10262/20002, making these transducers suited for torque studies on aerospace hydraulic motors and pumps. Other applications include dynamometers, drive shafts, transmissions, fans, and electric motors. Optional pickup provides output proportional to speed.

NK Technologies    Campbell, CA 95008
Jun 20, 2011 Monitoring resistive or inductive loads to detect current usage on large machines using AC current, ATCR Series flexible loop current transducers consist of sensing coil and True RMS signal conditioner. Each model uses 2 wires to provide power supply and output signal, allowing installer to pass coil around conductors without disconnecting existing wires. Supplied in 35 mm DIN-rail mount enclosure, series offers single range functionality and output magnetically isolated from input.

PennEngineering® (Penn Engineering)    Danboro, PA 18916
Jun 20, 2011 Used where only one side of panel is accessible for hardware installation, portable ATLAS® AE938 installs steel, brass, aluminum, or stainless steel blind threaded inserts that provide strong threads in thin panel sections. Pressure-controlled setting allows for installation of same insert type into various material thicknesses without requiring adjustment, while pull-to-pressure feature helps extend life of tool's mandrel. Auto-reverse mode is also standard.

International Microsystems, Inc.    Milpitas, CA 95035
Jun 20, 2011 Featuring on-board Linux OS and SATA/SAS capabilities, modular M3300 can concurrently test up to 32 devices. Supported form factors include 3.5, 2.5, and 1.8 in. as well as custom SSDs using SATA I (1.5 GBps), SATA II (3 GBps), SATA III (6 GBps) single-channel interfaces or SAS (6 GBps) one- and 2-channel interfaces. Used for SSD production, engineering, and QA testing, product supports multiple test functions and logs results into SQL database.

Bud Industries, Inc.    Willoughby, OH 44094
Jun 20, 2011 Available with 4 casters, portable BudRack Professional Series features ventilated tempered glass front door, solid steel locking rear door, and removable locking sides for security and quick access. It handles 19 in. rack-mount component equipment such as computer servers, monitors, KVMs, networking, and test instruments. Rack has 2 pairs of fully-adjustable 14 ga panel mounting rails, and comes complete with either two 23 in. or four 31 in. depth fans to expel air from cabinet.