Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 Used for MIG, pulsed MIG, and flux-cored welding processes, Magnum® PRO 450/550 are rated for 100% duty cycle and designed/tested for extreme environment welding applications. Balanced, barrel-style handle provides comfortable grip and reduces fatigue, while industrial-grade construction with copper and aircraft-grade aluminum parts ensures optimal electrical contact and heat dissipation. Also, Copper Plus(TM) contact tips maximize diameter and tip volume by weight.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 Designed for continuous operation, Mobiflex® 100-NF is suited for construction or shop welding applications where removing welding fume from source is needed without filtration. Portable, low-vacuum system can adapt to various work locations and welding applications, including stick, TIG, MIG, and flux-cored. Components include 16 ft house/hood set and 16 ft exhaust hose set, which can also be used to extend hose/hood set to full length of 32 ft.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 Available in 2 bulk sizes (500 and 1,000 lb), Accu-Pak® Boxes for SuperArc® MIG wire are designed to meet needs of robotic welding applications with bulk quantities, mini pallets, and side view windows. These 100% recyclable products, which can be stacked up to 2 high, are optimized for portability due to forklift-ready, corrugated cardboard mini-pallets on 500 lb box and wooden mini-pallets on 1,000 lb.

National Instruments Corp.    Austin, TX 78759-3504
Aug 10, 2009 Intended for control, test, and embedded system development, LabVIEW 2009 addresses challenges of parallel hardware architectures through virtualization technology that utilizes multicore systems as well as compiler and IP that enhance FPGA design. In addition to simplifying real-time math, software makes it possible to deploy code to wireless sensor networks to build smart industrial measurement and monitoring systems and features solutions for testing multiple wireless standards.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 With low fume generation rates, UltraCore® 70C Gas Shielded Flux-Cored Wire optimizes cleanliness and visibility while welding. Diffusible hydrogen levels are controlled at H8 AWS classification to provide resistance to hydrogen induced cracking. Optimized bead stacking and slag removal minimize clean-up time for multi-pass welding. Wire meets requirements of structural fabrication, heavy equipment, and ship building industries.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 Designed to meet requirements of heavy equipment, structural fabrication, and mining industries, gas-shielded UltraCore® 75C provides optimized stackability for welding thick steel sections. Basic slag system offers resistance to hydrogen induced cracking in many applications, including difficult-to-weld materials and restrained joints. Charpy V-notch test results are capable of exceeding AWS E70T-5C-JH4 impact requirements of 20 lbf-ft at -40°F.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 For fabrication shops dealing with small- to medium-sized parts, eCell(TM) LR provides flexible automation layout that delivers consistent and predictable production. Power Wave® i400 welding power source and AutoDrive(TM) 4R90 welding wire drive are employed for MIG, synergic MIG and MIG pulse welding, or flux-cored arc welding. Supplied as pre-engineered system, cell has 80 x 50 in. footprint and takes advantage of reach/stroke ratio and axis speeds of Fanuc ARC Mate® 50iC/5L robot arm.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 10, 2009 Built around 54 MHz, 10-bit ADC, Model MAX9526 provides 4x oversampling while consuming 200 mW during normal operation and 100 µW in shutdown mode. Supply voltage range of 1.7-3.5 on digital I/O eliminates need for external level shifters when interfacing with video processor. Power-over-Ethernet allows use of existing Cat-5 wiring for both data transmission and power. Designed to power up in fully operational mode, unit automatically configures itself to decode NTSC or PAL input standard.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 10, 2009 Supplied in 4 x 4 mm, 28-pin TQFN package, MAX8903A DC-DC charger employs 4 MHz (typ) switching frequency to minimize heat and charge time. All power switches and current-sense circuitry required for charging and switching load between battery and external power are included, along with Smart Power Selector(TM) circuitry. Charger can operate with separate inputs for USB and AC-adapter power or from single input that accepts both. Charge current is adjustable up to 2 A.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 10, 2009 Model MAX7036 superheterodyne receiver integrates self-contained PLL block; 400 kHz IF filter with RSSI; and analog baseband, data-recovery circuitry. Operating over -40 to +105°C temperature range from 3.3 or 5 V power supply, it offers sensitivity of 109 dBm and draws less than 1 µA in shutdown mode and 5.5 mA in receive mode. Power-down pin puts unit in low-current sleep mode and automatic gain control circuit reduces LNA gain by 30 dB when input signal power is large.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 10, 2009 Housed in 38-pin TSSOP package, 4-channel 24-bit MAX11040 provides compensation for phase shift caused by resistor dividers, transformers, or filters at analog inputs through programmable delay of 0-333 µsec. Eight units can be daisy-chained to provide sampling capacity of up to 32 channels. With minimum SINAD of 90 dB and SFDR of 91 dB, ADC is suited for power-grid-protection equipment, as well as other applications that require conversions of simultaneously sampled channels between 0.25-64 kS/sec.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 10, 2009 Operating from 6-38 V supply, MAX9943 (single) and MAX9944 (dual) op amps consume 550 µA quiescent current per amplifier. They have 100 µV max input-offset voltage as well as 0.4 µV/°C offset drift and offer gain-bandwidth product of 2.4 MHz. Featuring 15 nV/SqrRtHz input-voltage noise density and 1 fA/SqrRtHz input-current noise density, MAX9945 operates from 4.75-38 V supply, consumes 400 µA quiescent current, and has gain-bandwidth product of 3 MHz.

Analog Devices, Inc.    Norwood, MA 02062-9106
Aug 10, 2009 Model ADuM4160 utilizes iCoupler® digital isolation technology to offer 5 kV rms medical-grade isolation, upstream short-circuit protection, and isolated 1.5 and 12 Mbps data rates. Combining high-speed CMOS and microtransformer technology, USB 2.0-compliant chip operates off 5 V USB supply or 3.3 V power using internal regulator. It provides isolated control of pull-up resistor, allowing peripheral to control connection timing. Also, 2 mA idle current eliminates need for suspend state.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 10, 2009 Designed using monolithic SiGe BiCMOS process, 2.0-3.9 GHz MAX19996A provides fully integrated downconversion channel, with +24.5 dBm IIP3, 8.7 dB conversion gain, and 9.8 dB typical noise figure. Unit features 2LO-2RF spurious rejection of 67 dBc for RF level of -10 dBm, and 62 dBc for level of -5 dBm. Housed in 5 x 5 mm, 20-pin TQFN package, device supports both high- and low-side LO injection architectures for 2.3-2.9 GHz WCS, LTE, WiMAX(TM), and MMDS base stations.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 10, 2009 When configured as downconverter, Model MAX2051 provides 35 dBm of IIP3, 24 dBm of IP1 dB, 7.4 dB of conversion loss, and 7.8 dB noise figure. SiGe passive mixer exhibits 2 x 1, 2 x 2, and 3 x 3 spurious suppression, with typical values of 88, 79, and 101 dBc, respectively, over entire 50-1,000 MHz IF band. As upconverter, MAX2051 delivers 33.4 dBm of IIP3, conversion loss of 7.5 dB, and better than 61 dBc of LO ±2IF and 78 dBc of LO ±3IF suppression.

Future Facilities Inc    San Jose, CA 95110
Aug 10, 2009 6SigmaET enables building of models entirely from intelligent objects, which accelerates model creation, enables automatic gridding, and simplifies post-processing. In addition to multi-grid solver technology, software utilizes intelligence contained in every aspect of model to enable automatic meshing. Solution also solves conduction equations required to accurately simulate rotated or angled geometry.

Cyber-Tech, Inc.    Portland, OR 97281
Aug 10, 2009 Offered with choice of standard, sealed, or proportional switch functions, EG-930 Pro Series Ergo-Grip® comes in ergonomic, die cast aluminum housing that is unaffected by chemicals or UV rays. Proportional Pro-Switch, included, uses Hall-effect technology in environmentally sealed enclosure and provides smooth linear output of 0.5-4.5 Vdc for precise control. Up to 4 switch functions are available in right- or left-hand configurations.

Kalamazoo Machine Tool, Inc.    Portage, MI 49002
Aug 10, 2009 Model C320SA, designed for semiautomatic operation, is suitable for production sawing of tubes, profiles, and small solids. It features 17 and 34 rpm spindle speeds while accepting blades with up to 12½ in. dia. Offering simplified controls, it incorporates powered vise and downfeed control. Device includes heavy-duty precision-ground saw bed, TEFC 3-phase 2½ hp drive motor, enclosed transmission, and removable full-blade guarding.

Kalamazoo Machine Tool, Inc.    Portage, MI 49002
Aug 10, 2009 Model CT 350 A-NC is fully automatic high-speed circular saw suitable for use on aluminum extrusions, small aluminum solids, and other nonferrous materials. Utilizing 14 in. carbide-tipped sawblade and spray mist coolant, it can yield 50 rms quality cuts at 90°, or 45° left and right, with accuracy of ±0.005 in. Saw features twin pneumatic vises with infinitely variable clamping pressure and programmable control with digital entry for lengths and storage of up to 99 jobs.

Kalamazoo Machine Tool, Inc.    Portage, MI 49002
Aug 10, 2009 Offering full-cycle semi-automatic operation, model H310SA incorporates sawframe which automatically senses vise clamps and material size, lowers to cut at preset rate, and automatically returns to clear workpiece after cut. Unit provides vibration-free cutting and includes 12½ in. vise opening, 10 in. capacity, infinitely variable blade speeds from 60-360 fpm, and double mitering 45° left and 60° right. Also, it features TEFC 3-phase 2 hp drive motor and worm gear transmission.