Pickering Interfaces Inc    GRANTS PASS, OR 97526
Nov 16, 2009 Available in 32 x 8, 24 x 8, 16 x 8, and 8 x 8 configurations, 50 W Model 60-770 is contained within 3U rack mountable chassis with SMA front panel connectors. Housed in 6U rack mountable case, 75 W Model 60-730 comes in 32 x 16, 16 x 16, 16 x 8, and 8 x 8 configurations with F type front panel connectors, allowing device to be used in typical coaxial video applications. Both offer optimal crosstalk and isolation characteristics.

AMETEK Technical & Industrial Products    Kent, OH 44240
Nov 16, 2009 Available in 2.080, 2.552, and 3.025 in. lengths, 30 mm Pittman® Series 8540 achieves continuous torque up to 9.3 oz-in., peak torque up to 78.7 oz-in., speeds to 6,440 rpm at continuous torque, and continuous power up to 43 W, depending on model. DC motors integrate bonded neodymium magnets, 7-slot straight armature, diamond-turned commutator, and copper-graphite brushes. PC board brush card with integral surface mount components incorporates electrical noise suppression.

Thermo Electron Corporation / Molecular Spectroscopy    Madison, WI 53711-4495
Nov 16, 2009 Escalab 250Xi X-ray photoelectron spectrometer lets analysts configure it with range of surface characterization techniques. Ion scattering spectroscopy and reflection electron energy loss spectroscopy are provided, while ultra violet photoelectron spectroscopy and Auger electron spectroscopy are available as options. Sample preparation chamber is also provided, and system can be expanded with selection of sample preparation options and additional experimental chambers.

Elobau Sensor Technology, Inc.    Lake Bluff, IL 60044
Nov 16, 2009 Based on Hall effect technology, Model 175D provides 2 output signals which can be combined in 8 different options, including 0.5-4.5 V ratiometric outputs proportional to rotation of thumbwheel, and switching outputs. Illumination is provided by 3 LEDs or 1 multifunction LED that will switch colors when function is activated. Operating from -13 to +175°F, IP67 rated thumbwheel can be incorporated into joystick, multifunctional handle for shifter, or control panel.

Atmel Corporation    San Jose, CA 95131
Nov 16, 2009 AT90SO series is built on secureAVR® 8-/16-bit rapid, low-power RISC architecture with 288 KB ROM, 128 KB EEPROM, and 12 KB RAM. All standard cryptography algorithms (AES, DES/TDES, RSA, ECC) are supported by embedded dedicated accelerators, which are compatible with Common Criteria EAL4+ and FIPS140-2 certifications. Supported interfaces and peripherals include ISO7816, hi-speed SPI, full-speed USB 2.0, I²C, and GPIO.

Basler Vision Technologies    Exton, PA 19341
Nov 16, 2009 Basler ace series industrial GbE cameras include CCD sensor as well as high-performance FPGA with automatic parameter adjustment functions and software trigger for high-speed triggering via GigE bus. Software SDK and viewer tool is included, which runs on Windows and Linux. Featuring C-mount adapter, cameras are available in 4 models in monochrome and color with resolutions from VGA to 2 megapixels. Power-over-Ethernet option is available.

Basler Vision Technologies    Exton, PA 19341
Nov 16, 2009 Based on KAI-2050 and KAI-2150 CCD sensors, aviator area scan cameras are available in 2 models that offer 1,600 x 1,200 pixels or 1,920 x 1,080 pixels, at 67 or 62 fps, respectively. They provide progressive scan readout and global shutter technology. Register-based type interface simplifies camera configuration and units also include C/C++ high-level API, based on pylon platform, which includes 100 code samples to simplify integration.

Delcam Plc    Birmingham Hampshir B10 0HJ  United Kingdom
Nov 16, 2009 DentMILL knowledge-based machining system simplifies programming for manufacture of dental bars, implant bridges, and customized abutments. It enables use of multithreading technology to minimize calculation times for users with multiprocessor computers. Based on PowerMILL CAM system, program accepts data from any dental design system or scanner capable of exporting data in STL format. It can also output machining toolpaths to any CNC machine.

Konica Minolta Business Solutions U.S.A., Inc    Ramsey, NJ 07446
Nov 16, 2009 Piezo on-demand KM1024 series inkjet print head features 1,024 nozzles and 72 mm wide head, maximizing productivity. Able to reproduce 360 x 360 dpi images in up to 8 grayscale levels, product can be used with solvent, oil, and UV inks. It incorporates low capacitance actuators to limit power consumption. Measuring 131 x 18 x 89 mm and weighing 140 g, Product enables compact design of head mount systems.

Pepperl + Fuchs, Inc.    Twinsburg, OH 44087 2245
Nov 16, 2009 Intended for plastic fiber optic cables, SU18 and SU19 Photoelectric Fiber Optic Sensors feature multiple detection modes, selectable timing functions, remote teach capability, and 4-in-1(TM) output. Latter automatically selects NPN light/dark on and PNP light/dark on output options from single sensor. While SU18 series is available in pushbutton or potentiometer adjustable versions, SU19 series offers 4-digit, percentage-of-light-received LED display and glass detection mode.

Matrox Graphics Inc.    Dorval Quebec H9P 2T4, CD   Canada
Nov 16, 2009 Capable of supporting 8 DisplayPort or DVI Single-Link outputs from one workstation, Matrox M9188 PCIe x16 Octal graphics card offers 2 GB memory, resolutions to 2,560 x 1,600 per output, and desktop management features. Support for stretched or independent desktop modes across all monitors facilitates efficient management. Also available, Matrox M9128 LP PCIe x16, DualHead DisplayPort graphics card can drive applications across 2 displays at resolutions to 2,560 x 1,600.

Aeroflex Laboratories    Plainview, NY 11803
Nov 16, 2009 Operated via touchscreen UI, 7000 Series Vector Analyzer Generator provides integrated approach to measurements for complex wireless standards. Modular, software-defined functionality provides flexible, future-proof platform for wireless technologies such as LTE, GSM/GPRS/EDGE, 3G/HSPA, and WLAN. As many as 2 signal generators can be integrated for intermodulation and other key tests, and operating frequency range is 1 MHz to 6 GHz, with 90 MHz bandwidth for generation and analysis.

Electro-Chemical Devices, Inc.    Yorba Linda, CA 92887
Nov 16, 2009 Featuring ISE technology, HYDRA C22 can be used to monitor ammonium nutrient load directly in aeration basin of wastewater treatment plant as well as environmental waters, lakes, streams, and wells. Device uses Ammonium Ion Electrode, Potassium Ion Electrode, and pH Electrode to measure ammonium and potassium in concentrations from 0.1-1,000 ppm, pH from 0-14, and temperature from 32-212°F. Housed in NEMA 4X enclosure with backlit LCD, analyzer can operate up to 200 m from sensor.

Centorr/Vacuum Industries, Inc.    Nashua, NH 03062
Nov 16, 2009 Featuring compact furnace layout with construction on structural steel base, MIM-Vac(TM) M is offered in 18 x 18 x 36 or 48 in. sizes to meet demands of metal injection molding (MIM) industry. Use of Molybdenum alloys in hot zone and retort offer creep resistance, high recrystallization temperatures, and long service life, while Sweepgas(TM) technology promotes consistent gas flow dynamics over all parts. Dry mechanical pumping system with T/P binder condensing trap is also featured.

HASCO Hasenclever GmbH + Co KG    Ludenscheid D-58513  Germany
Nov 16, 2009 Designed to control temperature in 2-128 zones, Model Z1240 utilizes PID control technology that is accurate to 1/10°C. Integrated diagnosis program detects wiring errors and thermocouple breaks, while fuses protect control from mains voltage at sensor inputs caused by short circuits. Through automatic comparison with last used output levels, deviations are displayed, informing operator of imminent malfunctions, corrosion, soiling, or possibility of heating failure.

HBM, Inc.    Marlborough, MA 01752 3014
Nov 16, 2009 Multi-purpose torque flange, T40, is available with rated torques of 200 and 500 Nom as well as 1, 2, 3, 5, and 10 kNom. Identical electrical configuration throughout series allows use in various applications without modification. Able to handle numerous torque measurement applications on test benches and in process monitoring, product is insensitive to parasitic loads and ensures secure, error-free measured value acquisition/transmission even under difficult ambient conditions.

austriamicrosystems AG    Premstatten   Austria
Nov 16, 2009 Operating from 1.2-3.6 V supply, AS1371 LDO can function at input voltages down to 1.2 V. It offers dropout voltages of 20 mV at 100 mA and 80 mV at 400 mA as well as 50 µA quiescent current at maximum load. Unit is available with preprogrammed output voltages between 0.6-3.3 V, programmable in 50 mV steps. Featuring -40 to +85°C operating temperature range, it also includes overtemperature/overcurrent protection, under-voltage lockout, and low battery detection.

Master Magnetics, Inc    Castle Rock, CO 80104
Nov 16, 2009 Available in 14 x 6.25 x 1.5 in. rectangle, 9.5 x 5.6 x 1.5 in. rectangle, and 6 x 1.25 in. round sizes, Magnetic Parts Trays are suited for any project involving assembly and disassembly with small metal parts. Trays feature corrosion-resistant stainless steel construction and permanent magnets covered with rubber footing to prevent scratching and damage to surfaces. They can be used horizontally, vertically, or even upside down.

Master Magnetics, Inc    Castle Rock, CO 80104
Nov 16, 2009 Available in screw-mount and magnetic-mount styles, 12 in. Magnetic Knife and Tool Holder holds up to 30 lb/in. Unit stores frequently used knives, utensils, and tools for quick access. Magnetic mount style bar attracts to any ferrous metal surface with permanent magnets, will not slip from mounted position, and is movable to other work areas.

Steinmeyer Inc.    Bedford, MA 01730
Nov 16, 2009 Available with 0.5-3 mm leads, 5 mm Miniature Ball Screws come in 4 nut styles. Single nut Series 1112 has connecting thread without wipers, while single nut Series 1412 has double flange and wipers on both ends, and Series 1214 consists of cylindrical nut without wipers. Using end-cap ball returns manufactured from plastic rather than metal tubes, single nut Series 2422 is virtually noiseless. Applications include micromanipulators, miniature robotics, and compact actuators.