Lumex Inc.    Palatine, IL 60067
Jun 25, 2009 QuasarBrite Narrow Beam SMT LEDs are available in 4, 6, and 8 mm sizes with respective beam angle ranges of 12°-22°, 14°-24°, and 14°-28°. LED is mounted upside down and shines directly into internal parabolic reflector, providing high-intensity brightness (100 cd) in narrow beam of red, green, or blue light without external optics. Internal parabolic reflector also collimates light into beam, allowing high-intensity light to be produced by standard LED with 75 mW or less draw.

Sterling Instrument    New Hyde Park, NY 11042-5416
Jun 25, 2009 Consisting of 2 opposing disk halves with rare earth magnets, Series S50DCM and S50DCMM are available in 8 bore sizes from .1875-1.000 in. and 5-19 mm, respectively. Torque applied to one disk is transferred through air gap to other disk. Flat design enables angular misalignment up to 3° or parallel misalignment up to ¼ in. while still transmitting nearly full rotational torque. Made of 416 stainless steel, couplings have NdFeB, nickel-plated magnet and range from 1.72-2.86 in. O.D.

Henkel Corporation    Rocky Hill, CT 06067
Jun 25, 2009 Producing 15 releases per application, VOC and organic solvent free Frekote® Rel-Eaze(TM) can be applied at room temperature and cures at ambient temperatures within 30 sec. Low viscosity liquid can be sprayed on as thin coating using high-volume, low-pressure spray systems or wiped on with cotton cloth. When touch up is required, molding can continue immediately after touchup coat is applied. Product is available in 1 gal cans, 5 gal containers, and 55 gal drums.

LSI Computer Systems, Inc.    Melville, NY 11747
Jun 25, 2009 Designed to drive latching relay, LS6506R can be used in Wall Switch configuration (no Neutral) to enable full AC Mains cycle to be applied across any load. Also available, LS6507R drives triac in series with load and is suitable for use in lower-cost Wall Switch configuration for driving incandescent lamp loads. ICs can be used to manually or automatically switch loads on/off, and feature is offered where lights can be manually switched off and remain so while motion is detected.

Ondrives Ltd.    Chesterfield, Derbyshire S41 9RN  United Kingdom
Jun 25, 2009 Used in applications with vibrations and crushes, servo-insert couplings exhibit dampening attributes caused by spider element, available in different shore hardnesses, positioned between 2 hubs. Pluggable design facilitates accelerated assembly, and hub styles include shaft fixing with set screws, clamp hubs, or outer conical hubs. Offered with torque ranges from 1.2-940 Nm, non-wearing and maintenance-free couplings are resistant to environmental influences and temperatures.

ACI-ecotec GmbH & Co KG    Schwarzwald   Germany
Jun 25, 2009 Providing inline separation of mono- and polycrystalline solar wafers with thicknesses up to 120 µm, ecoSplit IXL features output capacity of 3,000 wafers/hr in continuous operation. System is equipped with 2 loading stations, onto which sawn wafers are placed in stacks of up to 250 pieces after pre-cleaning and manual inspection. Separation technology makes it possible to reduce breakage rates to 0.1%. After separation, wafers are fed to individually adapted transport units for cleaning.

Tractel, Inc., Griphoist Div.    Canton, MA 02021
Jun 25, 2009 Suited for Wind Industry, Derope emergency evacuation/controlled descent device offers descent speed and twin exit hubs that optimize efficiency and durability. Additional features include dual descent control pig tails, external cooling fins, integrated rope locking cleat, and completely sealed brake housing. Able to pass CSA ridge wet and cold testing procedures, product supports crank handle, ladder, and tripod bracket options.

Linear Technology Corp.    Milpitas, CA 95035
Jun 25, 2009 Designed for single-cell Li-Ion/Polymer batteries, Models LT3650-4.1 and LT3650-4.2 operate from 4.75-32 V and have 40 V absolute maximum rating. Model LT3650-4.1 offers 4.1 V battery float voltage, while Model LT3650-4.2 features 4.2 V final charge voltage. Once charging is terminated, devices automatically enter low current standby mode that reduces input supply current to 85 µA. Housed in 12-pin, 3 x 3 mm DFN package, both 1 MHz chargers operate from -40 to +85°C.

New Avionics Corp.    Fort Lauderdale, FL 33306
Jun 25, 2009 With adjustable ice sensitivity to less than 0.001 in., Ice*Meister(TM) Model 9734-HTR allows any controlling host to respond to earliest formation of ice and take remedial action in real-time. Pulsing 1.2 A at 24 Vdc, sensor's radiant heater heats sensor probe and melts away offending ice, while gravity alone removes icemelt. Temperatures of aluminum heater panels are limited to 50°C for personnel safety. Applications include webcams, radio towers, weather stations, and telescopes.

Helical Solutions Llc    Gorham, ME 04038
Jun 25, 2009 Model H35AL-2R is 2-flute, high-performance end mill that optimizes material removal rates in roughing and pocketing applications, maximizing room for chips. It features 35° helix angle and choice of 2 corner radii for each cutter size from 1/8-1 in. diameter. Crafted of certified premium submicron grain carbide, unit is designed for roughing and slotting applications and is available in stub and regular lengths. It is also available uncoated or with Zirconium Nitride coating.

Schurter, Inc.    Santa Rosa, CA 95403
Jun 25, 2009 Available in single- and double-pole versions, Model MSM LA offers point or ring illumination, actuator travel of greater than 5 mm, and switching voltages up to 125 Vdc/250 Vac. Unit comes in 19 and 22 mm mounting diameters, with red, green, or blue illumination, making it suited for application in dimly lit areas or to indicate On/Off status. Featuring IP67 protection rating from front, stainless steel vandalproof switch withstands temperatures from -40 to +85°C.

Northwest RF Corp.    Bensenville, IL 60106
Jun 25, 2009 Designed for welding thermoplastics such as PVC, EVA, PU, PETG, and polyolefins, Weldpro 4.0 Welder/Sealer offers infinitely adjustable power output from 0-4 kW that can be set in 4 independently adjusted stages for both power and duration. Modular system includes auto-tuning feature and arc suppression as standard. Typical applications include sealing clamshell/blister packages, tubing and perimeter tear-seals for medical bags, seam seals, and joining rolls of material.

Elma Electronic Inc.    Fremont, CA 94538
Jun 25, 2009 Available in vertical and horizontal orientations, high temperature Elma dual light guides can go through vapor-phase and reflow solder ovens without being damaged. They withstand solder heat levels at 260°C for 40 sec, or 200°C for 180 sec. Thermoplastic material provides optimal lumination on radiating surface and high mechanical strength. Lightpipes are RoHS compliant, and can be inserted on all standard insertion machines.

Label-Aire Inc.    Fullerton, CA 92833
Jun 25, 2009 Designed to support variety of pressure-sensitive applicators/printer applicators, rugged stands are built using 3 x 4 in. steel tubes, are covered with powder coat finish, and feature locking casters. Offered in T-, U-, H-, W-, Low-Boy, and H-Base Low-Boy configurations, all models are available with food grade casters, leveling feet, and stainless steel construction. Low-Boy stand models feature low clearance design with low clearance casters.

Daimer Industries Inc    Woburn, MA 01801
Jun 25, 2009 Suited for continuous cleaning of low-pile carpets, XTreme Power® XPH-9650 carpet cleaners feature 2 inline heating elements, dual 3-stage motors, air flow of 200 cfm, and water lift of 150 in. They come with 12 in dual-jet wand, 100 ft of solution hose, and 100 ft of vacuum hose, along with 17 gal solution tank and 15 gal recovery tank. Machines also include quick-drying technology and optional wands are available for upholstery/spot cleaning and stairs.

Electro Standards Laboratories    Cranston, RI 02921 3403
Jun 25, 2009 Available in rackmount configuration, Model 7435 allows sharing single port RJ45 interface device connected to COMMON port among 2 other devices connected to A and B ports for each of 16 channels. Port position of A and B can be configured manually by GUI or automatically via programming. Unit controls position of individual channels by sensing incoming data on ports A and B every millisec and switching them appropriately.

American Zettler, Inc.    Aliso Viejo, CA 92656 4115
Jun 25, 2009 Suited for use in industrial controls and appliances, AZ1641, AZ1651, and AZ1661 general purpose relays offer coils from 6-240 Vac and 6-220 Vdc. They come with optional LED indicator and can be used in building automation, system integrators, robotics, control boards, motion controls, I/O modules, and elevator controls.

Neutrik    Lakewood, NJ 08701
Jun 25, 2009 Providing dust and water resistant assembly for D-Shaped chassis connectors, SCDP gasket is designed for use with opticalCON DUO and QUAD fiber connectors and/or any Neutrik product using standard D-style cutout, including water resistant USB/FireWire and HDMI feedthroughs. Gasket is available in 6 different colors including black (SCDP-0), red (SCDP-2), yellow (SCDP-4), green (SCDP-5), blue (SCDP-6), and white (SCDP-9).

Wireworks Corp.    Hillside, NJ 07205
Jun 25, 2009 Simplifying set up by eliminating need to make individual connections directly to equipment and wall panels, AV2000 multi-pin connector system can accommodate audio, high definition video, data over Cat6 cabling, and control signals in single sophisticated hybrid connector. System utilizes 3 components; access point, umbilical and link, and can be integrated into any existing AV system. Applications include multi-media presentation rooms, corporate board rooms, and classrooms.

ITT Interconnect Solutions    Santa Ana, CA 92705
Jun 25, 2009 Offering contact counts of 1-600, Chip-on-Flex (CoF) connectors are available in rack and panel, circular and D-subminiature configurations. Filter design features one standard flex per layout and utilizes flexible circuit internal to connector, with chip capacitors surface-mounted on small pad adjacent to feed-thru contact. Tested to MIL-DTL-38999 Series III mechanical shock, vibration, and high altitude DWV specifications, connectors exceed 1,000 cycles of thermal shock per MIL-STD-1344.