Bosch Rexroth Corp., Linear Motion & Assembly Technologies Div.    Charlotte, NC 28273
Aug 13, 2010 Designed for eLINE profiled rail systems, Cam Roller Runner Blocks run at speeds up to 12 m/s and consist of aluminum body with corrosion-resistant cam rollers. Units replace standard plastic end caps with aluminum versions, have holes to allow venting, and use vacuum-compatible grease, enabling smooth, quiet travel in vacuum environments. Available in sizes 15 and 25, runner blocks offer choice of standard length with 4 cam rollers or shorter length with 2 cam rollers.

Renishaw, Inc.    Hoffman Estates, IL 60192
Aug 13, 2010 Providing true absolute positioning in linear/rotary models, RESOLUTE(TM) has single-track optical scale that eliminates misalignment and allows wide setup tolerances. Resolution of 1 nm at up to 100 m/s accommodates linear and angle encoding applications, and absolute position is acquired immediately upon switch-on and without battery backup. Product reads fine-pitch, 30 µm scale, resulting in noise levels with jitter less than 10 nm RMS. Sub-divisional error is ±40 nm.

Newport Electronics, Inc.    Santa Ana, CA 92704
Aug 13, 2010 With Model iSD-TC, users can monitor and record temperature of critical equipment and locations over Ethernet network or Internet via Web browser. Device can trigger alarm if temperature goes above or below user-determined set point, and alarms can be sent by email to single user or to group distribution list, including text messages to cell phones and PDAs. Supplied with removable 2 GB Flash Memory card, monitor enables user to store up to 7 years of readings taken at 10-sec intervals.

AMETEK Solidstate Controls    Columbus, OH 43085
Aug 13, 2010 Designed to measure temperatures from -4 to 2,912°F with ±1% accuracy, FTi-E Fixed Thermal Imaging System provides complete thermal view of process with display that responds immediately to changes, which can then be used to trigger alarms, automatically control process, or provide quality control information. Thermal imager, housed in NEMA 4, RF-shielded enclosure, can operate continuously without user intervention and can be controlled remotely via local touchscreen interface or PC.

AMETEK Solartron Metrology    Gastonia, NC 28054
Aug 13, 2010 Designed to test electrical properties of materials ranging from insulators to superconductors, ModuLab MTS combines time domain tests and AC tests together with wide range of modules, providing high voltage, high current, resolution, and sample/reference measurements. Core of system is MAT core module, which makes use of DSP technology to provide accurate experiment control, data acquisition, data averaging, and responsive safety and step limit detection.

SUYIN Connector GmbH    Pfarrkirchen 84347  Germany
Aug 13, 2010 Model 100016FB013M205ZL RJ45 jack measures 16.75 x 14.0 x 11.3 mm and integrates two status LEDs and shielding for protection against EMI. Able to withstand high removal forces, 8 position, 8 contact SMT jack has 2 THT solder tags that ensure effective ground connection while maintaining hold on board in conjunction with 5 THT LED solder contacts. Location of side connecting contacts and part of rear contacts beneath jack housing also keeps board layouts compact.

SUYIN Connector GmbH    Pfarrkirchen 84347  Germany
Aug 13, 2010 Model 020200MA005S538ZL, 5-pole vertical Mini USB jack B-type has 5 SMT contacts as well as 3 solder latches at sides providing total area of 15.6 mm². Measuring 9.9 x 3.9 x 7.3 mm, it is designed for mobile devices as well as industrial I/O solutions requiring compact design, high stability, and secure retention forces.

Aps Novastar LLC    Huntingdon Valley, PA 19006
Aug 13, 2010 Designed for short run, mixed technology applications, Models ESS310 and ESS500 handle max board size of 12 x 12 in. and 19.7 x 19.7 in., respectively, while providing single point, drag, mini-wave, or dip soldering. Machines feature 100% IR preheat, 33 lb solder capacity, and spray flux system. With warm up time of approximately 45 min, systems reach max temperature of 725°F and consume 0.8-1.7 cfm nitrogen, depending on nozzle and nozzle shroud.

Aps Novastar LLC    Huntingdon Valley, PA 19006
Aug 13, 2010 Featuring self-contained fluxing, preheating, and laminar solder wave modules, Model EWS-310 offers continuous width adjustment for boards up to 11.8 in. Machine has welded steel frame, on-board profiler, 200 lb solder pot capacity, and max conveyor speed of 98.4 ips. With warm-up time of approximately 60 minutes, Model EWS-310 provides max Preheat 1 temp of 302°F and max Preheat 2 temp of 392°F. It is compatible with both lead and lead-free processes.

Aps Novastar LLC    Huntingdon Valley, PA 19006
Aug 13, 2010 Complementing SMT placement applications with its operational speeds to 3,000 cph, benchtop LE40V employs Windows®-based GUI that enables board programming within minutes. It places range of components, including 0201s, LEDs, BGAs, 15 mil pitch QFPs, SMT connectors, and offers on-the-fly component centering using vision (Cognex®), laser technology (Cyberoptics®), or mechanical fingers. Self-contained system accepts boards to 13.5 x 22 in. and offers placement accuracy of ±0.001 in.

Bridgeport Magnetics    Bridgeport, CT 06608
Aug 13, 2010 Designed for power utilities and companies active in construction and power distribution, 8 kVA PhazeSaver can restore power to homes/businesses that lose partial service. It supplies temporary 120 or 208/240 V service until permanent repairs can be completed, allowing utility companies to avoid bridging or running shunts. Also, 240 V power can be supplied from single 120 V phase or from service with open neutral (and 2 good phases) on overhead 120/240 and underground 120/208 systems.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 13, 2010 Providing 12-cell measurement, Model MAX11068 employs capacitor-isolated SMBus-laddered communication bus, which allows up to 31 devices to be connected in series to monitor up to 372 cells. Analog front-end combines 12-channel voltage-measurement data-acquisition system with fault-tolerant switch bank input. Using 12-bit ADC to digitize cell voltages, MAX11068 delivers less than ±0.25% error over normal battery temperature ranges and ±20 mV error over full AEC-Q100 Type 2 temperature range.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 13, 2010 Available in 2 x 12 W, 2 x 20 W, and 1 x 40 W configurations, MAX98400 Series features anticlipping circuit that avoids clipping by automatically reducing amplifier's gain when supply voltage is insufficient to deliver desired output voltage. Thermal foldback prevents unwanted thermal shutdown events by reducing output signal when internal junction temperature exceeds +120°C. Specified over -40 to +85°C extended temperature range, devices are suited for TVs, notebooks, and desktop PCs.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 13, 2010 Supplied in 28-pin TQFN, MAX5971B single-port power-sourcing equipment (PSE) controller delivers up to 40 W/port for IEEE® 802.3af/at-compliant, high-power power-over-Ethernet (PoE+) applications. It integrates 0.5 X power MOSFET, sense resistor, and current monitor, and typical application circuit requires fewer than 8 external components. Operating from 32-60 V, IC provides 9-bit ADC and I²C interface as well as device discovery, classification, and DC/AC load-disconnect detection.

Radiometrix Ltd.    Watford Hertfordsh WD19 5EZ  United Kingdom
Aug 13, 2010 Acting as transparent serial cable to attached host, TXL2/RXL2 Modules provide preamble, synchronization, bit balancing, and error checking along with automatic noise squelching. Simplex, multi-channel OEM radio modems feature baud rate of 9,600 bps, transmit power of +10 dBm at 10 mW, and receiver sensitivity of -107 dBm for 1% BER. For multiple radio systems, TXL2/RXL2 can be set to 1 of 8 unique addresses and allow operation on 1 of 5 pre-set frequencies in 433 MHz band.

Smart Sonic Corp.    Van Nuys, CA 91405
Aug 13, 2010 Fully automatic and programmable, ErgoSonic facilitates front-loading of stencil at safe and comfortable height and does not require stencil basket. System is compatible with closed-looped cleaning chemistries, is completely self-contained, and does not require drain. Ultrasonic wash, rinse, and optional dry cycle is completed in minutes, and user never comes in contact with cleaning chemistries, vapors, or contaminated waste streams.

Smart Sonic Corp.    Van Nuys, CA 91405
Aug 13, 2010 Model 6000-LC, Large Capacity Stencil Cleaner is suitable for backplane, motherboard, and other large stencils up to 30 x 60 in., and can be modified to accommodate stencils as large as 40 x 72 in. Low-profile unit features adjustable loading height to simplify loading and unloading, as well as touchscreen programmable controller that stores multiple cleaning profiles. Model 6000-LC cleans any type of solder paste from any fine-pitch aperture.

Smart Sonic Corp.    Van Nuys, CA 91405
Aug 13, 2010 Available in ready-to-use spray bottles, 440-R SMT Detergent replaces hazardous solvents with safe, water soluble detergent that cleans effectively to optimize print production. RoHS-compliant product eliminates noxious odors and hazards associated with solvent cleaning. It is non-flammable, has no VOCs, and is safe on all metals and plastics.

Control Co.    Houston, TX 77258 8307
Aug 13, 2010 Constructed of ABS plastic, Traceable® Waterproof Type K Thermometer reads from -328 to +2,372°F and -200 to +1,300°C with respective resolutions of 0.1° and 1°. Microprocessor updates display 2.5 times per second, and 5/8 in. high digits can be read up to 10 ft away. Waterproof design stops dirt, dust, fume, and water ingress, and rubber boot for probe connector lets unit remain waterproof with thermocouple attached. Min/Max recall and set point differential features are standard.

Makita U.S.A., Inc.    La Mirada, CA 90638
Aug 13, 2010 Powered by 18 V LXT Li-Ion Battery Technology, Model BHR241 features variable speed motor that delivers 1-1,000 rpm and 0-4,000 bpm. Three-mode operation allows for rotation only, hammering with rotation, or hammering only. Providing 7/8 in. capacity in concrete and ½ in. capacity in steel, tool has chisel that rotates 360° with 40 locking positions, built-in clutch that minimizes gear damage by disengaging gears if bit binds, and Rapid Optimum Charging System that charges battery in 30 min.