Magnetic Products, Inc.    Highland, MI 48357
Jun 10, 2011 Used to remove fine metal contaminants in dilute-phase pneumatic conveying, Pneumatic Line Magnets (PLM) have sanitary design in all product contact areas, quick-release clamps to facilitate opening/closing, 100% stainless steel product areas, and Rare Earth magnet material. Food-grade, closed-cell gasket provides permanent seal, while seam-welded, magnetic, stainless steel, raised pole design promotes tramp metal retention between cleaning.

MAG IAS, LLC    Erlanger, KY 41018
Jun 10, 2011 Designed for workpieces up to 2,700 mm dia, multi-axis Model VTC 2500H combines gear hobbing and milling with turning, drilling, threading, and contouring capabilities. Machine can turn blanks and subsequently cut gear teeth in one setup. It can also perform rough turning of outside diameter and gear cutting on inside diameter in one set up. Available with 36 or 46 kW power, 2 different heads can hob modules up to 24.0 mm or form-mill teeth up to 28.0 mm on parts with max face width of 600 mm.

Electro-Mech Components, Inc.    South El Monte, CA 91733 3689
Jun 10, 2011 Incorporating NVG Green-B light filters into Series 600 Quad Lamp/LED pushbutton switch series, Model SW44752 offers Night Vision Imaging System compatibility. Series 600 has ratings of 2.0 A resistive and 0.5 A inductive at 30 Vdc or 115 Vac. Requiring 2 lb of operating pressure, switches have minimum rated life of 100,000 actuations. Units are available with various lens cap, lens base, and lens filter materials, as well as multiple sockets that allow four T-1-¾ MFB based Green LEDs at 28 Vdc.

Mocon    Minneapolis, MN 55428
Jun 10, 2011 Targeting companies and laboratories dealing with food, GreenLight(TM) 930 provides aerobic plate count (APC) or total viable count (TVC) of food sample's microbial load using sensing assay or vial. Results, depending on bacterial load, can be obtained between minutes and 8 hr, and process is automated via 48-position carousel inserted into main unit. System feeds bacterial information to PC via dedicated software; pass/fail and multipoint modes are also available.

National Semiconductor Corp.    Santa Clara, CA 95051-0695
Jun 10, 2011 Supplied in 40-pin thermally enhanced LLP, LM3435 drives 3 common anode RGB high-brightness LEDs sequentially with one inductor. LEDs are powered one after another at 60 Hz and above to match operation requirements of liquid crystal on silicone (LCoS) or digital light processing (DLP) image devices. Along with I²C control interface, this switching-mode constant current regulator integrates all active components and accepts 2.7-5.5 V input.

Thomas & Betts Corp.    Memphis, TN 38125
Jun 10, 2011 With Catamount® Twist Tail® Cable Tie, users can bend and twist off tail after installation, leaving no sharp edges to scratch cables or hands. Available in white or UV-resistant black 6.6 nylon, cable tie provides 30 lb of minimum loop tensile strength, which is suitable for light-duty applications.

Magna-Power Electronics    Flemington, NJ 08822
Jun 10, 2011 Offering front panel control, metering, and calibration, 250 kW MT Series V Power Supply integrates harmonic neutralizer, which creates 12-pulse AC waveform, minimizing harmonic distortion. Neutralizer suppresses AC harmonics by multiplying number of input phases with autotransformers. In addition to RS-232 interface and programmable SCPI command set, power supply features current-fed power processing, which delivers additional power processing stages for protection under abusive loads.

Wilks Enterprise, Inc.    East Norwalk, CT 06855
Jun 10, 2011 InfraCal Ethanol Blend Analyzer lets terminal managers, distributors, fleet managers, and regulators measure percent ethanol in gasoline to ensure correct blend. Designed for use by non-technical personnel, portable unit can take on-site measurements in under 1 min at fuel terminals and service stations or perform tanker spot checks without waiting for off-site test results. Self-contained unit incorporates calibration program, direct readout display, and RS232 interface.

Electro Standards Laboratories    Cranston, RI 02921 3403
Jun 10, 2011 Model 9067 allows user to switch device connected to COMMON port between devices connected to ports A or B. Up to 8 switch modules can be housed in one Model 9025 Rack Chassis, and modules with various switch functions can be added to this system as requirements develop. Switch is manually operated from front panel, and all 8 pins of RJ45 interface are switched. Rated for 10/100Base-T networks up to CAT5, module incorporates sealed switch with self-wiping precious metal contacts.

BLM Group USA    Wixom, MI 48393
Jun 10, 2011 Tube cutting system TC720 operates as stand-alone unit or as part of automated tube processing line controlled by single CNC, integrating downstream functions such as deburring, washing, drying, and accumulating. Programming system automatically selects optimum parameters for job at hand, and complete changeover can be accomplished in less than 3 min with all settings centralized and to scale. Saw performs cutting of square and rectangular sections with slideway mounted cutting head.

Omega Engineering, Inc.    Stamford, CT 06907
Jun 10, 2011 Supplied with 5-point NIST traceable calibration, PXM409 Series Transducers and Transmitters are constructed of welded stainless steel and are suited for scientific or industrial applications requiring low thermal drift. CE compliant units are available in metric ranges of gauge, compound gauge, absolute, vacuum, and barometric pressure. Featuring standard G ¼ metric fitting, PXM409 Series is available with cable, DIN connector, or 4-pin M12 electrical terminations.

National Instruments Corp.    Austin, TX 78759-3504
Jun 10, 2011 Part of NI-XNET family of network interfaces, 9862 C Series high-speed CAN module includes hardware-accelerated messaging, onboard frame processing, and communication with 100% bus loads without dropped frames. Module allows engineers to develop in-vehicle networks as well as diagnostics, and perform device validation with synchronized DAQ. Software tools and APIs to accelerate development are included, and product can be incorporated into CompactDAQ and CompactRIO CAN platforms.

Waters Corp.    Milford, MA 01757
Jun 10, 2011 Intended for routine quantitative LC/MS/MS analysis, Xevo® TQD tandem quadrupole mass detector features universal ion source architecture. Laboratories can utilize ZSpray(TM) and access variety of ionization modes. Automated quantification workflow tools minimize variability between departments, laboratories, and operators. Also included, RADAR(TM) technology lets users monitor for matrix interferences, metabolites, impurities, and degradants in samples while quantifying target compounds.

Futurestate IT inc.    Toronto, ON M4P 1E2
Jun 10, 2011 AppRx(TM) Application Currency Management (ACM)(TM) platform let users assess, plan, and execute migration of applications for Windows® 7 or Server 2008 as well as determine if/how applications can be virtualized. Along with App-DNA Inc.'s AppTitude and additional supports for MS App-V and Citrix XenApp, solution provides centralized and streamlined application currency management for ongoing business as usual changes - service packs, security updates, and software upgrades- to IT environment.

General Dynamics C4 Systems    Scottsdale, AZ 85257
Jun 10, 2011 Equipped with Intel® Core(TM) i7 processor, Model GD8200 combines Wi-Fi 802.11, Bluetooth, and 4G mobile broadband technology to enable seamless roaming for uninterrupted connectivity. Sunlight-viewable DynaVue® II touch screen display delivers clarity and detail when viewing maps and videos, while anti-theft and user authentication technologies keep data safe and protected. Sealed against dust and water, IP65-rated unit withstands drops, shock, vibration, and extreme temperatures.

RIDGID    Elyria, OH 44035
Jun 10, 2011 Featuring capacity up to 1 5/8 in. OD, Model TC-40 cuts polyethylene, polypropylene, PEX, rubber hose, PVC, and CPVC. Unit features 75 W motor that drives pointed X-CEL® blade to provide square, precise cut in 4 seconds. Repeat cuts can quickly follow with use of push-button blade release. Forward and reverse blade operation is possible via single trigger on front of tool. Powered by detachable 12 V Li-ion battery, TC-40 can make up to 250 cuts/charge.

RIDGID    Elyria, OH 44035
Jun 10, 2011 Able to record still images and video with one touch from user, SeeSnake® CS-10 features video and image playback as well as auto-log recording method with automatic file compression. SeeSnake® HQ software, included, consists of PC-based program that allows images and video of inspection to be imported and stored on computer for sharing via various means. Also, monitor's 12.1 in. size and daylight readability promotes clear viewing and diagnosis of line blockages via SeeSnake cameras.

Linear Technology Corp.    Milpitas, CA 95035
Jun 10, 2011 To address high-density footprints of multimode 4G RRH (Remote Radio Head) MIMO receivers, LTC5569 offers 26.8 dBm IIP3 and operating frequency range of 300 MHz to 4 GHz. IC comes in 4 x 4 mm QFN package and can be configured to operate on any cellular band from 700 MHz to 2.7 GHz. It also features conversion gain of 2 dB and noise figure of 11.7 dB as well as inputs that can withstand strong in-band blocking interference signals without significantly degrading noise figure.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Jun 10, 2011 With Electromagnetic Professional 2011.07, users can analyze electrical performance of packages, connectors, antennas, and other RF components. Program includes Eigenmode solver, which finds resonant frequencies for cavity filters. Filter designers can visualize resulting electromagnetic fields at each resonant frequency and make adjustments to cavity structure to optimize performance. PC board designs can be imported from Cadence Allegro for signal integrity and EMI analyses.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Jun 10, 2011 Handling both MIG and flux-cored gas-shielded or self-shielded processes, POWER MIG® 180 Dual is designed for sheet metal welding, light-frame auto body work, and small shop applications. User can select 120 V input power for home and generator-driven environments or 208/230 V for shop applications or thicker material. Featuring feeder speed of 50-500 ipm, welder has 30-140 A output range operating on 120 V input power or 30-180 A output operating on 208/230 V.