Meggitt Sensing Systems (Endevco Corp.)    San Juan Capistrano, CA 92675
Dec 05, 2002 Hermetically sealed Model 752A offers IEEE P1451.4 Transducer Electronic Data Sheet (TEDS) capabilities and is available in 100 mV/g version and 1 V/g version. Able to withstand rough handling without sustaining internal damage, unit incorporates 10-32 top connector and hex mounting base utilizing 10-32 mounting stud. It can be powered by any signal analyzer with 2-10 mA constant current supply. Accelerometer includes PIEZITE® Type P-8 crystal element.

Artesyn Communication Products Inc.    Madison, WI 53717
Dec 05, 2002 Dual-output, non-isolated, point-of-load (POL) converter for DDR (double data rate) memory, DDR12, enables 2.5 V VDDQ supply for DDR logic and 1.25 V DDR termination voltage (VTT) to be derived from single module. Unit employs synchronous rectification techniques and has 85% conversion efficiency when operated at half-load or greater. The 2.5 V VDDQ output delivers up to 25 A, and 1.25 V VTT output delivers up to 8 A for use with DDR-SDRAM devices.

Emerson Process Management    Knoxville, TN 37932
Dec 05, 2002 Modular FieldQ incorporates Intelligent Position Tracking technology for final control applications using on/off and modulating valves. It delivers predictive, diagnostic data to enterprise about operating performance and health of device. Actuator break time, travel time, and cycle counter are also reported. FieldQ is compatible with several standard communications protocols, including AS-i bus, Profibus DP, and FOUNDATIONâ„¢ fieldbus.

GSI Lumonics    Northville, MI 48167
Dec 05, 2002 Models JK401 and JK501 Nd:YAG systems offer 400 and 500 W peak power, respectively. SuperModulationâ„¢ technology momentarily doubles output intensity and allows user to control weld penetration, heat effected zones, cooling rates, kerf quality, cornering speeds, and burnback. Fiber-optic beam delivery system has built-in process detection and intuitive, self-protecting diagnostics. Multiplexing options, time-shares, and energy-shares are available.

Smith & Loveless, Inc.    Lenexa, KS 66215 1234
Dec 05, 2002 With vacuum pump shelf, S-Conversion Formula X® allows municipalities and Wet Well Mounted Pump Station owners to upgrade while reusing existing rotating assemblies, vacuum pumps, and control panel. Retrofit package includes piping, control panel mounting system, man-way split cover access, and base. Product also includes float/transducer access port, enclosure ventilation system, and split easy-roll hood and track system.

TechniDrill Systems Inc.    Kent, OH 44240
Dec 05, 2002 Model 100CR utilizes counter-rotation of workpiece and cutting tool to attain accuracies up to .005 in. runout in 40 in. depth. Precise laser alignment enables unit to work within close tolerances. With effective drilling depths to 48 in., Product offers drilling ranges from .125–1.000 in. in diameter. System is equipped with programmable controls and coolant system with 5 micron filtration.

Hohl Machine & Conveyor Co., Inc.    Buffalo, NY 14213
Dec 05, 2002 Manufactured with heavy-duty, extruded-aluminum rail, Adapt(TM) Conveyors employ frame that can accommodate chain, power and free, tabletop, or belt conveyors in same rail. Units offer modular drives, take-ups, and pop-up transfers, and can be utilized with or without pallets for progressive, synchronous, or non-synchronous assembly line operations. T-slot rails allow for bolt-on mounting of supports, guides, electrical controls, and part positioners.

Bristol Equipment Co.    Yorkville, IL 60560
Dec 05, 2002 Machine-mounted, see-thru BristolGuard® provides personal safety barrier for workers who operate or watch debris-slinging processes. Polycarbonate panel is 9 in. high by 14 in. wide and helps meet OSHA regulations. Two-piece, steel mounting arm, offered in 20 and 31 in. lengths, holds shield securely in place and is jointed with 5 pivot points that allow virtually any desired shield placement. Vertical handgrip allows control of multi-directional movement.

Process Electronics Corp.    Gastonia, NC 28056
Dec 05, 2002 Monopolarizer uses combination of electronic devices to provide precise control of electric current used in plating process. It eliminates plating interruptions due to and solves passivation and peeling quality issues due to ripple current.

Emerson Process Management / Process Liquid Division / Uniloc Division    Irvine, CA 92606
Dec 05, 2002 Züllig dissolved oxygen system reduces cleaning and calibration frequency in harsh wastewater treatment environments. Solid-state, galvanic sensor has 2 insulated electrodes that are continuously polished by rotating, diamond grindstone. Self-cleaning process eliminates manual cleaning and replacing of membranes and replenishing of electrolyte solution.

JLG Industries, Inc.    McConnellsburg, PA 17233 9533
Dec 05, 2002 SkySaw™ integrates concrete wall saw system into aerial work platform and includes SkyCleaner™ pressure-washing system. Onboard hydraulic manipulator holds concrete saw and guides it along bolt-on track for precision cuts. Able to be operated by one worker, hydraulic pump powers saw, drill, and manipulator. Hydraulic hoses and water lines are located inside boom's power track. Adjustable system is capable of spraying at 1,000–3,500 psi. It includes two 150 gal water tanks.

Hoffer Flow Controls, Inc.    Elizabeth City, NC 27909 6726
Dec 05, 2002 Hose Series flowmeters are offered in sizes ¼ in. through 3 in. and provide accurate flow rate measurement of ±.5% of reading over linear flow range. Barbed end connections are for permanent installation and beaded connections are meant for test installation or applications which are expected to be moved around.

Zero-Max, Inc.    Plymouth, MN 55441 5509
Dec 05, 2002 Zero-Max Crown gear drives provide directional motion change in power transmission systems. Sealed from contaminants, products offer class 10, hardened spiral drive bevel gears permanently mounted to shafts with locking pins. Equipped with non-magnetic, stainless steel shafts, right angle drives are available in 2- and 3-way models with 1:1 and 2:1 speed ratios. Internal gears stay permanently aligned, lubricated, and free of outside dirt and debris.

French Technology Press Office, Inc.    Chicago, IL 60601
Dec 05, 2002 Equipped with integrated NC control that stores pre-recorded shapes, semi-automatic 132 NC enables operators to switch from product to product by selecting required program. Product changes can be made in less than 30 sec. Rolling process and NC control enable machine to produce up to 180 parts per hour in various shapes, including round, oval, square, and triangular. Up to 100 different programs can be memorized.

Positronic Industries, Inc.    Springfield, MO 65801 8247
Dec 05, 2002 Low profile Goldfish Series is offered in 2 package sizes with variety of contact sizes and configurations. Current ratings to 35 A per contact for size 12 contacts. Connectors are available with straight solder, right angle solder, and straight press PCB terminations. Sequential mating, selective loading, mounting brackets, and push-on fasteners are optional.

Samtec, Inc.    New Albany, IN 47151 1147
Dec 05, 2002 Power Mate™ IPBS Series .165 in. pitch socket mates with IPBT Series header for isolated connection in parallel or perpendicular board orientations. IPBD Series discrete wire socket mates to IPBT Series header for wire-to-board connection. Units transfer up to 15 A through each contact in board-to-board applications and up to 12 A in wire-to-board situations using 18 AWG wire. Pin counts range from 4–30 positions in dual row design.

Edwards Vacuum Technology    Wilmington, MA 01887
Dec 05, 2002 Aluminum gate and angle valves are suited for isolation of roughing lines and fore-lines in vacuum processes where high conductance is required. Gate valves (GVA) and angle valves (AVA) range in size from 2-24 in. and are offered with ASA flanges. When loss of power/pneumatic pressure occurs, valves close, isolating vacuum system. During servicing, valves remain in situ for removal of actuator assembly. Optional indicator displays open/closed position.

Reid Supply Co.    Muskegon, MI 49444
Dec 05, 2002 Available in various sizes with satin and mirror finishes, handles are NSF certified and meet Food Equipment Industry Standard. Applications include pharmaceutical, chemical, and marine industries.

Milacron Inc.    Cincinnati, OH 45206
Dec 05, 2002 Magna V vertical injection molding machines (IMMs), based on C-frame platform, measure 15 x 7 ft. Vertical IMMs are available in stationary, shuttle, or rotary table versions. With 3-sided access, units provide tandem variable volume and fixed-volume pump systems, infrared light curtain, and XTREEM PC-based, open-architecture control. Units have maximum daylight of 35 in. and accept molds up to 24 x 36 in. (2-station). They suit insert, over-molding, and multi-component applications.

Carpenter Technology Corporation    Wyomissing, PA 19610-1339
Dec 05, 2002 High-temperature alloys in strip form are used in making parts and components that require heat resistance in environments up to 2000°F. Strips range from 0.003–0.24 in. thick in widths from 3/8–13 1/2 in., depending on alloy. They are offered in tempered or annealed condition. Applications include aerospace fasteners, turbine blades, jet engine components, heat shields, mechanical seals, flexible bellows, stampings, and heat treating equipment.