EXAIR Corporation
Cincinnati, OH 45249-1621
Jul 22, 2008 Powered by compressed air, E-Vac series is comprised of low-vacuum units up to 21 in. Hg for porous materials and high-vacuum units up to 27 in. Hg for non-porous materials. Vacuum pumps are available in various sizes and flows, and selection of suction cups is available for range of applications. Engineered to minimize air consumption and increase cycle speeds, series has in-line, single stage design that delivers consistent, steady vacuum without fluctuations.

Binks ITW Industrial Finishing
Glendale Heights, IL 60139
Jul 18, 2008 Suited for small and medium wood shops, Binks Comet 4/12(TM) pump is designed with air powered 12:1 two-ball piston pump that is capable of producing 0.4 gpm at 60 cycles/min. Created to apply water-borne and solvent-borne coatings, it can spray wood coatings at fluid outlet pressures from 300-1,200 psi. Available in wall-mount, cart-mount, or tripod-mount outfits, pump features balanced fluid section for steady, even coating flow and hard chrome coated SS pump rod.

Thomas Products Division
Sheboygan, WI 53081
Jul 17, 2008 Rated for max flow of 2.37 cfm, Series 660/680 WOB-L® pumps incorporate wetted aluminum parts treated for corrosion protection and single-phase AC motors of permanent split capacitor design. Oil-less pistons and cylinders, in addition to intake filters, ensure non-contaminated air flow, while SS valves, piston seals, hard-coated aluminum cylinders, and permanently lubricated bearings help extend product life. Pumps provide up to 28.5 in. Hg vacuum or 45 psi pressure.

Viking Pump Inc., A Unit Of IDEX Corp.
Cedar Falls, IA 50613 0008
Jul 17, 2008 Dimensionally interchangeable with Viking Heavy Duty Bracketed packed and sealed pumps, Universal Mag Drive Series facilitates upgrade process. Sealless offering features thrust-controlled design, allowing short-term run-dry capabilities and bi-directional pump operation for application flexibility. Offered in cast iron, steel, and stainless steel, products are suited for use with hazardous, hard-to-seal liquids and offer flow rates to 200 gpm with pressures to 200 psi.

Watson-Marlow Bredel Pumps
Wilmington, MA 01887
Jul 11, 2008 Suited for harsh processing applications, Model 520RE high-pressure chemical metering peristaltic pump offers flows of 55 gph at 30 psi to 7 gph at 100 psi. It covers range of applications including low shear feed for contamination-free transfer of acids, bases, and slurries found in chemical-based industries. With repeatability at 99.5%, self-priming pump can accommodate flow rates from 0.1 µL to 350 gpm, and can withstand pressures up to 232 psi.

Binks ITW Industrial Finishing
Glendale Heights, IL 60139
Jul 07, 2008 Designed for high-flow circulation systems requiring moderate pressure, Exel(TM) pump works with water-borne and solvent-borne fluids, catalyzed coatings, high solids coatings, abrasive materials, and moisture-sensitive materials. Available in three 4:5.1 all-stainless-steel models, it delivers up to 6.85 gpm at 60 cycles/min. Pump features maximum inlet and working pressure of 100 and 450 psi, respectively, and SS wetted fluid chambers with self-priming pistons.

Sauer-Danfoss
Ames, IA 50010
Jul 03, 2008 Utilizing integral electro-hydraulic servo piston assembly to controls rate and direction of hydraulic flow, Model H1 115/130cc is designed for high and medium power mobile machinery that demands steady, instant propulsion and precise control. Closed-circuit, variable displacement, axial piston pump supports next generation engines as industry moves toward Tier 4 emission controls. It is fully PLUS+1(TM) Compliant to interface with company's electronic machine control architecture.

Seepex Inc.
Enon, OH 45323
Jul 01, 2008 MD and BW pumps are available with drive that integrates single reduction gear reducer, 4-pole TEFC, inverter-rated ½ hp electric induction motor, and vector type variable frequency drive in NEMA 4 enclosure. Pump and drive combination, covering performance band of 0.08-4.7 gpm and pressures to 360 psi, operates from 1x120 Vac, 15 A circuits with 5-15p grounded plug. Drive has H-O-A switch with 10-turn potentiometer for manual control and will accept 4-20 mA process signal.

GIW Industries, Inc.
Grovetown, GA 30813
Jun 30, 2008 Along with proprietary impeller vane design and Solid/Fluid Flow Technology, LCC-R pump features double-wall construction with outer ductile-iron casing and inner molded-rubber liners. Thickened shrouds and vanes provide optimal wear resistance in heavier slurries, and impeller hub side clearing vanes are effective in clearing solids. Rubber-lined impeller is interchangeable with existing metal impellers. Hub side clearing vane and flat hub side designs are available.

GIW Industries, Inc.
Grovetown, GA 30813
Jun 30, 2008 Used in hard rock mining, MDX series has low specific speed that provides stable operations by harnessing variable flow conditions confronted in modern mills. Stable flow in combination with optimum head/quantity and efficiency curve ensures efficient mill operation. Also, optimal BEP ensures stable sump level over large flow variations, operational efficiency, and equipment life. Pumps also incorporates slurry diverter technology matched with adjustable suction liner design.

CAT PUMPS
Minneapolis, MN 55449
Jun 25, 2008 Capable of delivering 10 gpm, 7CP6110BH103 and 7CP6110BH153 are 10 and 15 hp single-extended shaft motor-pumps, respectively, that operate at pressures to 1,460 and 2,000 psi. Products mount onto motor using bell housing and flexible coupling and are constructed with forged brass manifold and STG V-Packings. Dipstick is included for checking oil level. Applications include coolant flushing systems, dual gun prep units, and multi-gun truck wash systems.

Bosch Rexroth Corp., Industrial Hydraulics Div.
Bethlehem, PA 18017
Jun 17, 2008 With 6,500 bar nominal pressure and 9 nominal parameters that counteract reduced speed of diesel engine, A4VG variable pump with swashplate design lowers emissions for travel drives used in mobile equipment. Pump case provides manufacturers with ways to include sensors for monitoring swivel angle, high pressure, and rotational speed. Bowl-shaped design avoids high-pressure transitions at sealing points, while high-pressure ports help optimize arrangement of hydraulic lines.

Sta-Warm Electric Co.
Ravenna, OH 44266
Jun 12, 2008 With heating element wrapped around outer surface, Heated Transfer Pump provides uniform heat to inner portion of pump to prevent cooling of temperature-sensitive materials conveyed through gravity fed transfer lines. Unit has max operating temperature of 375°F and can transfer tar, wax, glue, and potting compounds. Pumps operate in 120, 240, or 480 V systems, have output of 1-50 gpm at 100 psi max, and are available in bronze, cast iron, or stainless steel.

EXAIR Corporation
Cincinnati, OH 45249-1621
Jun 10, 2008 Utilizing SS 2-way pump that is suited for use with most non-flammable liquids, Mini Reversible Drum Vac System can vacuum coolant, hydraulic oils, spills, sludge, tramp oil, and waste water; then pump it back out for disposal, storage, or reclamation. Compressed air powered unit has no moving parts such as motors or impellers to clog, freeze up, or wear out. With air consumption of 19 scfm at 80 psig, it features automatic safety shut-off valve to prevent overfilling.

KNF Neuberger, Inc.
Trenton, NJ 08691-1810
Jun 09, 2008 Featuring explosion-proof AC motors, KNF corrosion-resistant pumps are equipped for gas and liquid handling in potentially hazardous locations. Offering compliance with Class 1, Division 1, Groups C & D, and ATEX hazardous locations, they can achieve flows up to 7.8 scfm and vacuums up to 29.86 in. Hg, depending on model. They provide oil-free operation, run without wear-prone sliding seals, include quality precision ball bearings, and come in 3 head configurations.

Haight Pump, Div. Of Baker Manufacturing Company
Evansville, WI 53536
Jun 06, 2008 Employing minimal parts to promote extended MTBF, DIU series is built with ductile iron housings, steel shaft and pinion gears, and iron rotor with multiple bearing materials. Shaft sealing includes packing seals, lips seals, and multiple mechanical seal types, with elastomers to suit. Along with built-in shaft seal flexibility, pumps feature direct drive speeds to 1,800 rpm and close coupled design that eliminates misalignment and related failures.

Finish Thompson, Inc.
Erie, PA 16501
Jun 03, 2008 Molded from corrosion-resistant GF Polypropylene or CF PVDF, DB22 models offer broad hydraulic coverage with working pressure capabilities up to 90 psi, max flow rates reaching 220 gpm, and discharge heads to 200 ft. Run-dry capability, with carbon bushing, minimizes repairs and production downtime, and ductile iron motor adapter mounts to NEMA or IEC frame motors. Models are available with open/closed impellers and NPT/BSP threaded, flanged, or union connections.

Bosch Rexroth Corp., Industrial Hydraulics Div.
Bethlehem, PA 18017
May 27, 2008 Suited for assembly of compact power packs, B Series pumps feature 7 cc per revolution, while G Series pumps have displacement of up to 63 cc per revolution for applications in upper power classes. U and T Series pumps offer low noise emissions and vibrations, and satisfy demands for all displacements between 4 and 63 cc per revolution. Individual/combined multiple external gear pumps are suited for machines with operating pressure of 4,000 psi and cover speed range up to 6,000 rpm.

Bosch Rexroth Corp., Industrial Hydraulics Div.
Bethlehem, PA 18017
May 23, 2008 Designed for working hydraulics in open circuits, Rexroth A10VO Series 53 medium-duty axial piston variable pump (250/315 bar) features hydraulic-mechanical power control or electro-proportional differential pressure control. Power controller prevents overloading of combustion engine, while electro-proportional swivel angle adjustment allows precise flow control and electronic limit load control.

Bosch Rexroth Corp., Industrial Hydraulics Div.
Bethlehem, PA 18017
May 23, 2008 Available in sizes of 71-140 and with pressure of 4,000/5,000 psi, Series 32 A10VO has housing design that reduces noise levels by up to 3 dB, while offering resistance to suction-pressure dips and housing-pressure peaks. It includes improved controllers for upper medium-duty range and safeguard feature that protects against excessively high pressure settings. Current controller generation integrates sealing concept for leak protection and resistance to dirt and contamination.