Hayward Industrial Products Inc., Hayward Flow Control Systems    Clemmons, NC 27012
May 21, 2012 T-Series Webster thermoplastic pumps feature single, non-coupled motor/impeller shaft with proprietary PTFE shaft seal design. Vertical seal-less immersible pumps are available from 1/3 to 1½ HP with standard and wash-down motors and as 115/230 V and 208-230/460 V models. Features include CPVC pump head and impeller, 303 SS shaft material and extended shaft sleeve. Applications include chemical processing and transfer, metal plating, water treatment, and mining.

General Monitors    Lake Forest, CA 92630
May 07, 2012 Drawing combustible or toxic gases at 0.05-1 lpm from monitored areas to gas detector, Model SM100 can measure potentially hazardous gases in areas that are remote, inaccessible, or too cold, hot, or wet for direct monitoring. Unit supplies gas for up to 3 gas detectors, which is useful for monitoring multiple gases in single line. Featuring 316 SS construction, module operates from -4 to +131°F and comes in both DC configuration and aspirated model that is used with compressed air source.

KNF Neuberger, Inc.    Trenton, NJ 08691-1810
Apr 23, 2012 Effective against pressures up to 90 psig, KNF SIMDOS® 10 Series transfers neutral or corrosive liquids with flow rate of 1-100 mL/min and dose volumes from 1-1,000 mL. Pumps can transfer viscous media at full flowrate up to 150 centistokes. Equipped with touch-control knob for setup and operation, pumps can run dry without damage, are self-priming up to 9 ft of water, and available with variety of wetted materials, including corrosion-resistant PTFE/FFPM.

Edwards High Vacuum Int'l    Crawley East Susse RH10 9LW  United Kingdom
Apr 17, 2012 Able to work in dirty environments, STP-iXR1606 series features IP54 protection equivalent against dust and humidity. Rotary design optimizes throughput at elevated gas flow rates and maximizes gas flow. Promoting energy conservation, fully integrated controller incorporates power supply to reduce energy consumption at elevated gas flows. Additional features include I/O remote, RS232C, RS485, and STP-link standard communication ports, with Profibus and DeviceNet available as options.

Finish Thompson, Inc.    Erie, PA 16501
Apr 05, 2012 PFS and TTS stainless steel drum pumps are available with threaded discharge fittings as standard options. These 1 in. MNPT and 1 in. FNPT discharge fitting options will be welded onto 1 in. barbed fitting, allowing customers to use special hoses, swivel fittings, quick disconnects, etc. Additionally, plastic fittings are available for PFP and PFV Models.

Grindex AB    Haninge SE-136 25  Sweden
Apr 03, 2012 Micro, Mini, and Solid pumps are respectively capable of handling 4, 6, and 7 Lps and pumping up to 10, 16, and 12 m. Suited for use in harsh environments, pumps incorporate air valve that cools motor when pump runs dry, water cut that prevents leakage through power cable, and thermal contact that protects motor from overheating. Additional features include double mechanical shaft seals in oil bath and rubber strainer. Facilitating service, Mini and Solid pumps have external oil plugs.

Lee Products Ltd    Buckinghamshire SL9 9QE  United Kingdom
Mar 28, 2012 Consuming 2.5 W for either 12 or 24 V operation, LPL2 provides standard dispense volumes of 50 µL dispense per shot. Port head design allows both tubing connections and manifold mounting for design flexibility. Designers can test fluidic system using connections to soft 1/16 in. tubing, then manifold mount the pump using standard O-rings once system design has been finalized. Electrical interface features contoured end-cap, which provides secondary connector retention.

Fortrans Inc.    Wendell, NC 27591
Mar 28, 2012 Resting above water drawn from concrete plant's cleanest detention basin or final weir, diffusion and injection chamber mixes CO2 gas into flowing water. Gas bubbles convert to carbonic acid and lower pH value. Specifically, concrete-grade 5000 Series models are set to lower settled process water to 7.5 pH, for release from plant property, and total suspended solids (TSS) to 14-17 range. CO2 gas-charged cylinder houses diffuser material and exhibits up to 90% gas utilization rate.

NLB Corporation    Wixom, MI 48393 2824
Mar 27, 2012 Using simple conversion kit, 125 Series water jet pump units can be converted to any of eight operating pressures from 6,000 to 40,000 psi. Series features flow ranges of 4.4 to 32.5 gpm and choice of 125 or 145 hp diesel or electric engine. Unit's ultra-high pressures offer flexibility to do diverse jobs with a single water jet pump unit. Applications include contractor and industrial uses such as, surface preparation, pipe/tube cleaning, concrete hydrodemolition, and more.

Kurt Manufacturing    Minneapolis, MN 55421
Mar 27, 2012 Designed for use with hydraulic vises, cluster towers, and swing clamps, 5,000 psi Hydraulic Pump is driven by pneumatic motor and operates from 90-145 psi shop air using foot pedal. Unit maintains constant pressure when foot pedal is depressed regardless of system pressure, ensuring accurate and repeatable clamping pressure with every clamping cycle. Designed for single acting systems, pump features internal load limiting valve, air exhaust muffler, and air/oil filters.

Enerpac (Industrial Tools)    Milwaukee, WI 53201 3241
Mar 16, 2012 To meet wind turbine market requirements, ZUTP1500 provides high flow at low pressure for accelerated system fills as well as controlled flow at high pressure for safe and accurate operation. This 3-piston, 2-stage pump, featuring universal motor, facilitates operation of bolt tensioners and hydraulic nuts in remote locations. While low pressure flow rate is 230 in.³/min, and full pressure flow rate is 20 in.³/min., pump generates up to 21,750 psi without the use of hydraulic intensifier.

Blackhawk Technology    Santa Cruz, CA 95060
Mar 16, 2012 Designed to perform in several landfill applications, Edge Pneumatic Piston Pump(TM) maintains constant flow rates regardless of TDH. Model 101 pumps down to 281 ft, while Model 102 pumps at constant 5.0 U.S. gpm to beyond 160 ft. With drivers and controls located above wellhead to facilitate service, products can pump highly viscous, hot, and harsh chemical liquids and feature dry running capability. Both models pump to well bottom, with controlled draw down and no wasted head over pump.

Xylem Inc.    White Plains, NY 10604
Mar 15, 2012 Offering 12 and 24 V models, industrial motor-driven Flojet® LF Plus series uses reciprocating diaphragm technology and performs in harsh environments. Design reduces diaphragm cleaning time, and 360° quick connect swivel ports allow complete freedom of port orientation. Weighing 20 oz, pump supports operating pressures to 40 psi, offers self-priming capabilities up to 6 ft, and offer 1.0 gpm flow rate. Additional features moderate pressures from 0.2-0.3 gpm for backpack spraying.

Wilden Pump & Engineering Co.    Grand Terrace, CA 92313
Mar 12, 2012 With 2 in. flow path and threaded 2 in. horizontal fluid connections, PX800 Advanced(TM) Series is suited for liquid-transfer applications where product containment and high flow rates are required. Center-ported units feature bolted construction with 316 stainless steel wetted path, BSPT or NPT threaded inlet/discharge connections, and variety of elastomer options, including neoprene, Buna®-N, EPDM, PTFE, and Viton®. Pumps deliver flow rates up to 176 gpm at operating pressures up to 125 psig.

Robbins & Myers Energy Services Group    Willis, TX 77378
Mar 07, 2012 Featuring metal-to-metal rotor/stator technology, Moyno HTD660(TM) suits high-temperature applications. Stator does not include elastomer, design handles downhole temperatures to 660°F, and closely controlled tolerances between metal-to-metal rotor/stator clearance promote optimal performance. Producing minimal vibration, design can also handle hot oil encountered during thermal recovery methods.

KNF Neuberger, Inc.    Trenton, NJ 08691-1810
Feb 27, 2012 Operating without pump oil or maintenance, LABOPORT® Vacuum Pumps integrate corrosion-resistant PTFE wetted parts, multi-port FFPM valves, and PTFE-bonded diaphragms. Portable units can handle most aggressive vapors and can tolerate occasional condensate. Depending on model, diaphragm pumps achieve flow rates to 60 L/min and generate vacuum to 29.9 in. Hg. Units are suited for laboratory applications involving rotary evaporation, vacuum ovens, and gel drying.

MOUVEX    Auxerre   France
Feb 24, 2012 Featuring seal-free design to eliminate leaks and product contamination, Abaque Series handles anything from abrasive and aggressive fluids to shear-sensitive and viscous materials. Self-priming pumps can run in forward or reverse and offer suction-lift capabilities to 25.5 ft, as well as ability to run dry. Available in ductile iron and stainless steel construction, pumps come in 10 sizes with flow rates from .07-339 gpm and discharge pressure to 232 psi.

Varna Products    Cameron Park, CA 95682
Feb 23, 2012 Powered by 1/10 hp, 24 Vdc brushless motor with integral drive electronics, TG-300 Variable Speed Low Flow Pump is designed for smooth continuous flows from 0-5 gph with viscosity range of 30-600 cSt. Unit can be set with 0-5 V analog signal and is suitable for fluids compatible with aluminum, steel, Viton, and Teflon wetted materials. Applications range from metering, dosing, and bottling to medical and chemical uses.

Fluid Metering, Inc. (FMI)    Syosset, NY 11791
Feb 15, 2012 Available with isolation gland to provide fluid barrier between pumped process fluid and atmosphere, Miniature H Series Valveless Pump Heads provide maintenance-free dispensing of saline-based reagents, buffers and wash fluids, slurries, abrasive fluids, inks, and anaerobic fluids. Isolation gland is connected to barrier liquid or gas source via barbed fittings. Pumps can be configured with AC, DC, hazardous duty, pneumatic, and stepper drive options, as well as programmable dispensing systems.

KNF Neuberger, Inc.    Trenton, NJ 08691-1810
Feb 09, 2012 Designed to operate intermittently or continuously against pressure up to 87 psig, Type NF1.25 offers solution for dosing or transferring liquids or liquid-gas mixtures at flow rates up to 300 ml/min. OEMs can choose from variety of motors, including iron core DC, ironless core DC, or brushless DC versions. Using PP, PTFE, EPDM, and FFMP materials for components that come into contact with pumped medium, pumps offer chemical resistance and require virtually no maintenance.